Mechanical Properties of Concrete Incorporating Pre-Treated Wastes Sawdust

2021 ◽  
Vol 895 ◽  
pp. 147-156
Author(s):  
Esam Hewayde ◽  
Ziyad Kubba
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Calcium Hydroxide ◽  
The Other ◽  
Concrete Mixture ◽  
Fine Aggregate ◽  
Distilled Water ◽  
Concrete Mixtures ◽  
Slaked Lime ◽  
Pre Treatment

This paper investigates the effect of using wastes sawdust as a replacement of fine aggregate (sand) on mechanical properties naming compressive, tensile and flexural strengths of ordinary Portland concrete. The wastes sawdust was treated before incorporating it in concrete mixtures. Three different methods were used to pre-treat the sawdust including a) soaking the sawdust in distilled water at 50 oC, b) soaking the sawdust in Ca (OH)2 solution, and c) soaking the sawdust in Ca (OH)2 solution and using a set accelerator in the concrete mixture. In addition to the control mixture (having no sawdust), three more concrete mixtures were prepared to explore the effect of the three different methods of pre-treatment on the mechanical properties of concrete. Results showed that the compressive strength of the concrete incorporating wastes sawdust pre-treated with the calcium hydroxide solution (slaked lime) and having the accelerator was higher than that of the control mixture. The tensile and flexural strengths of the concrete mixture having waste sawdust pre-treated by Ca (OH)2 solution and having the accelerator were found to be very comparable to those of the control mixture. On the other hand, the compressive, tensile, and flexural strengths of the concrete mixture with sawdust pre-treated by Ca (OH)2 solution only were somehow comparable to those of concrete mixture having sawdust pre-treated by distilled water. While the compressive strength of the concrete mixtures incorporating sawdust pre-treated with either Ca (OH)2 solution or distilled water was less than that of the control mixture, both tensile and flexural strengths of the two treated concrete mixtures were approximately comparable to those of the control mixture.

Compressive Strength of Concrete from Lightweight Bubbles Aggregate

2015 ◽  
Vol 754-755 ◽  
pp. 348-353 ◽  
Author(s):  
Norlia Mohamad Ibrahim ◽  
Leong Qi Wen ◽  
Mustaqqim Abdul Rahim ◽  
Khairul Nizar Ismail ◽  
Roshazita Che Amat ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Compressive Strength ◽  
Natural Resources ◽  
Concrete Structure ◽  
Concrete Mixture ◽  
New Materials ◽  
Concrete Mixtures ◽  
Compressive Strength Of Concrete

Compressive strength of concrete is the major mechanical properties of concrete that need to be focused on. Poor compressive strength will lead to low susceptibility of concrete structure towards designated actions. Many researches have been conducted to enhance the compressive strength of concrete by incorporating new materials in the concrete mixture. The dependencies towards natural resources can be reduced. Therefore, this paper presents the results of an experimental study concerning the incorporation of artificial lightweight bubbles aggregate (LBA) into cementations mixture in order to produce comparable compressive strength but at a lower densities. Three concrete mixtures containing various percentages of LBA, (10% - 50% of LBA) and one mixture used normal aggregate (NA) were prepared and characterized. The compressive strength of LBA in concrete was identified to be ranged between 39 MPa and 54 MPa. Meanwhile, the densities vary between 2000 kg/m3 to 2300 kg/m3.

scholarly journals Comparison Mechanical Properties of Two Types of Light Weight Aggregate Concrete

2019 ◽  
Vol 5 (5) ◽  
pp. 1105-1118
Author(s):  
Hesham A. Numan ◽  
Mohammed Hazim Yaseen ◽  
Hussein A. M. S. Al-Juboori
Keyword(s):  
Compressive Strength ◽  
Abrasion Resistance ◽  
Coarse Aggregate ◽  
Lightweight Aggregate ◽  
Peak Level ◽  
Concrete Mixture ◽  
Fine Aggregate ◽  
Concrete Mixtures ◽  
Light Weight Aggregate ◽  
Reference Mixture

This paper presents the behavior of concrete properties by replacing the conventional coarse aggregate used in the concrete mixture by two types of lightweight aggregate; Expanded Perlite Aggregate (EPA) and Volcanic Pumice (VP). To fulfill this aim; three laboratory tests were applied; density, compressive strength, and abrasion resistance, that conducted to extrapolate the range of the changes in the properties of concrete with existence those types of aggregate in the mixture. Also, the volumetric proportion adopted as a strategy for replacing the coarse aggregate by EPA or VP in the concrete mixture. Then, the volumetric proportion ranged from 10% to 50% with the variation step was 10%. Therefore, ten concrete mixtures are prepared and divided into two groups; each group contains five concrete mixes to represent the volumetric replacement (10-50)% of conventional coarse aggregate by EPA or VP. On the other hand, one extra mixture designed by using conventional aggregate (coarse and fine aggregate) without any inclusion of EPA or VP to be considered as a reference mixture. The obtained laboratory results of this study proved that the density, compressive strength, and abrasion resistance readings of concrete decreased at any volumetric proportion replacement of coarse aggregate by EPA or VP. The decrease in density and compressive strength of concrete readings amounted the peak level at 50% replacing of coarse aggregate by EPA, which were 38.19% and 77.37%, respectively than the reference mixture. Additionally, the compressive strength is an important factor affecting the abrasion resistance of concrete mixture, and loss of abrasion decreased as compressive strength increased.

scholarly journals INFLUENCE OF THE GRANITE SCREENINGS TO THE PROPERTIES OF THE CONCRETE PAVING BLOCKS

2012 ◽  
Vol 4 (3) ◽  
pp. 89-95
Author(s):  
Mindaugas Laurinavičius ◽  
Mindaugas Daukšys ◽  
Albertas Klovas
Keyword(s):  
Mechanical Properties ◽  
Frost Resistance ◽  
Physical And Mechanical Properties ◽  
Concrete Mixture ◽  
Fine Aggregate ◽  
Technological Properties ◽  
Research Results ◽  
Concrete Mixtures ◽  
Better Than ◽  
Durability Of Concrete

The research deals with the granite screenings as fine aggregate influence on the technological properties of concrete mixtures and on the physical and mechanical properties and durability of concrete paving. The following several compositions of concrete mixture for the production of environment arrangements are researched: fine aggregate using only 0/2 fraction sand (B1), 10% of 0/2 fraction sand replacing with 0/2 fraction granite screenings (B2) and using only granite screenings (B3). Concrete mixtures were prepared in the laboratory, and concrete paving blocks – in the factory. The technological properties of concrete mixtures and physical and mechanical properties of concrete paving blocks (made from the mentioned concrete mixtures) were determined; the durability of the products in the cycles of frost resistance was forecasted. The research results reveal that due to the properly selected ratio between sand and granite screenings in the fine aggregate, the characteristics of concrete paving blocks are better than using only sand as fine aggregate.

Study of Rheological Properties of Modified Concrete Mixtures at Vibration

2019 ◽  
Vol 968 ◽  
pp. 96-106
Author(s):  
Oleksandr Pshinko ◽  
Olena Hromova ◽  
Dmytro Rudenko
Keyword(s):  
Mechanical Properties ◽  
Rheological Properties ◽  
Physical Nature ◽  
Concrete Mixture ◽  
Practical Significance ◽  
Vibration Displacement ◽  
Concrete Mixtures ◽  
Variable Quantity ◽  
Vibration Compaction ◽  
Mechanism Of Interaction

Study of rheological properties of concrete mixtures based on modified cement systems in order to determine process parameters. Methodology. To study structural-mechanical properties of modified concrete mixtures of different consistency at their horizontal vibrating displacement an oscillatory viscometer was designed. Results. The optimization of the process of vibration displacement of concrete mixtures with the specification of parameters of vibration impacts taking into account structural-mechanical properties of the mixture is performed. It has been established that the viscosity of the modified cement system of the concrete mixture is a variable quantity, which depends on the parameters of the vibration impacts. Scientific novelty. The mechanism of interaction of the modified concrete mixture with the form and the table vibrator during its vibration compaction is determined. On the basis of this, a model of concrete laying process control is proposed, that allows to predict the ability to form a dense concrete structure. Practical significance. Disclosed physical nature of the process of vibrating displacement of modified concrete mixtures using the principles of physical-chemical mechanics of concrete allows reasonably choose the best options for vibration impacts.

scholarly journals THE INFLUENCE OF GRANITE SIFTINGS ON THE PROPERTIES OF CLEAVED SURFACE EXTERIOR CONCRETE BRICKS

2010 ◽  
Vol 2 (6) ◽  
pp. 43-49 ◽  
Author(s):  
Mindaugas Tumosa ◽  
Mindaugas Daukšys ◽  
Ernestas Ivanauskas
Keyword(s):  
Mechanical Properties ◽  
Concrete Mixture ◽  
Fine Aggregate ◽  
Technological Properties ◽  
Product Durability

Research deals with granite siftings as fine aggregate possibilities to be used for manufacturing cleaved surface exterior concrete bricks. The article describes the influence of granite siftings on the technological properties of concrete mixture and on the physical mechanical properties of cleaved surface exterior concrete bricks formed using these mixtures and forecasts product durability. The following several compositions of concrete mixture for producing exterior concrete bricks are composed: using only 0/4 fraction sand (B1) as a fine aggregate, using only 0/2 fraction granite siftings (B2), and 50% of 0/4 fraction sand replacing with 0/2 fraction granite siftings (B3) depending on the volume. The products were formed in metal moulds; at a later stage, they were cleaved in half. The technological properties of concrete mixture and the physical mechanical properties of cleaved surface exterior concrete bricks formed using the above introduced mixtures were tested forecasting product durability. The results of the conducted research reveal that due to the properly selected ratio between sand and granite siftings in the fine aggregate, granite siftings may be used for manufacturing cleaved surface exterior concrete bricks.

Investigation of the mechanical properties of concrete containing recycled aggregate and scrap crumb rubber and polypropylene fibers

2020 ◽  
pp. 147776062097750
Author(s):  
Moein Khoshroo ◽  
Ali Akbar Shirzadi Javid ◽  
Nima Rajabi Bakhshandeh ◽  
Mohamad Shalchiyan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Polypropylene Fiber ◽  
Crumb Rubber ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Fine Aggregate ◽  
Mixture Ratio ◽  
Coarse Aggregates

In this study, the effect of using crumb rubber and recycled aggregates on the mechanical properties of concrete has been evaluated as areplacement of fine and coarse aggregates In order to add the admixtures and evaluate their combined effect, 20 different types of concrete mixture ratio were prepared. The results indicated that in those samples containing crumb rubber and recycled aggregates the compressive strength is reduced and adding fiber up to 0.1%. to these concrete samples can improve the compressive strength Also, the tensile strength of the samples mixed with crumb rubber and recycled aggregates were decreased, and with the addition of propylene fiber up to 0.4%. the tensile strength slightly increased Moreover by adding the crumb rubber to the samples the elasticity modulus was reduced but by adding fiber to samples about 0.1% and 0.2.% the modulus of elasticity of concrete in all samples were increased. According to the results, it can be said that using the combination of 5% of crumb rubber as a replacement of fine aggregate, and the combination of 35% of recycled aggregates as a replacement of coarse aggregate, and also by adding 0.1% polypropylene fiber in volumetric percentage of concrete along with adding 7% of micro silica as a replacement of cement led to the best effect on the mechanical properties of concrete.

Recycling of Waste Limestone as Fine Aggregate for Conventional and Green Concretes

2018 ◽  
Vol 928 ◽  
pp. 257-262 ◽  
Author(s):  
Trong Phuoc Huynh ◽  
Chao Lung Hwang ◽  
Si Huy Ngo
Keyword(s):  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Concrete Mixture ◽  
Engineering Properties ◽  
Fine Aggregate ◽  
Normal Concrete ◽  
Design Algorithm ◽  
Green Concrete ◽  
Concrete Mixtures

This paper presents the results of the experimental works to investigate the use of waste limestone from water treatment industry as fine aggregate in green concrete. Two concrete mixtures with a constant water-to-binder ratio of 0.3 were prepared for this investigation, in which, the normal concrete mixture was designed following the guidelines of ACI 211 standard, while the green concrete mixture was designed using densified mixture design algorithm (DMDA) technology. For comparison, both types of concrete samples were subjected to the same test program, including fresh properties, compressive strength, strength efficiency of cement, drying shrinkage, electrical surface resistivity, ultrasonic pulse velocity, and thermal conductivity. Test results indicate that both concrete mixtures showed the excellent workability due to the round-shape of waste limestone aggregate and the use of superplasticizer. In addition, the green concrete mixture exhibited a better performance in terms of engineering properties and durability in comparison with the normal concrete mixture. The results of the present study further support the recycling and reuse of waste limestone as fine aggregate in the production of green concrete.

scholarly journals Prediction Models for the Mechanical Properties of Self-Compacting Concrete with Recycled Rubber and Silica Fume

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1821 ◽  
Author(s):  
Robert Bušić ◽  
Mirta Benšić ◽  
Ivana Miličević ◽  
Kristina Strukar
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Silica Fume ◽  
Prediction Models ◽  
Crumb Rubber ◽  
Fine Aggregate ◽  
Rubberized Concrete ◽  
Self Compacting Concrete ◽  
Recycled Rubber ◽  
European Standards

The paper aims to investigate the influence of waste tire rubber and silica fume on the fresh and hardened properties of self-compacting concrete (SCC) and to design multivariate regression models for the prediction of the mechanical properties of self-compacting rubberized concrete (SCRC). For this purpose, 21 concrete mixtures were designed. Crumb rubber derived from end-of-life tires (grain size 0.5–3.5 mm) was replaced fine aggregate by 0%, 5%, 10%, 15%, 20%, 25%, and 30% of total aggregate volume. Silica fume was replaced cement by 0%, 5%, and 10% of the total cement mass. The optimal replacement level of both materials was investigated in relation to the values of the fresh properties and mechanical properties of self-compacting concrete. Tests on fresh and hardened self-compacting concrete were performed according to the relevant European standards. Furthermore, models for predicting the values of the compressive strength, modulus of elasticity, and flexural strength of SCRC were designed and verified with the experimental results of 12 other studies. According to the obtained results, mixtures with up to 15% of recycled rubber and 5% of silica fume, with 28 days compressive strength above 30 MPa, were found to be optimal mixtures for the potential future investigation of reinforced self-compacting rubberized concrete structural elements.

scholarly journals THE DEPENDENCE OF THE PHYSICAL MECHANICAL PROPERTIES OF EXPANDED-CLAY LIGHTWEIGHT CONCRETE ON THE COMPOSITION

2010 ◽  
Vol 2 (6) ◽  
pp. 50-55
Author(s):  
Marija Vaičienė ◽  
Jurgita Malaiškienė
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Chemical Composition ◽  
Water Absorption ◽  
Lightweight Concrete ◽  
Physical And Mechanical Properties ◽  
Concrete Mixture ◽  
Active Filler ◽  
Binder Material ◽  
Substitute Materials

Binder material is the most expensive raw component of concrete; thus, scientists are looking for cheaper substitute materials. This paper shows that when manufacturing, a part of the binder material of expanded-clay lightweight concrete can be replaced with active filler. The conducted studies show that technogenic – catalyst waste could act as similar filler. The study also includes the dependence of the physical and mechanical properties of expanded-clay lightweight concrete on the concrete mixture and the chemical composition of the samples obtained. Different formation and composition mixtures of expanded-clay lightweight concrete were chosen to determine the properties of physical-mechanical properties such as density, water absorption and compressive strength.

scholarly journals MECHANICAL AND CHEMICAL ACTIVATION OF BLAST FURNACE SLAG AND ITS INFLUENCE ON THE MECHANICAL PROPERTIES OF THE RESULTING CEMENT PASTE

2021 ◽  
Vol 30 ◽  
pp. 30-35
Author(s):  
Jan Horych ◽  
Pavel Tesárek ◽  
Zdeněk Prošek
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Water Glass ◽  
High Speed ◽  
Chemical Activation ◽  
Waste Materials ◽  
Slaked Lime ◽  
Furnace Slag

The usage of waste materials is a very important global topic. The large amount of waste everywhere in the world needs to be processed or disposed. Landfilling is not an option anymore, because of European legislation and restrictions. A lot of studies are trying to develop new options or possibilities of using waste materials. This research is trying to find a way to process blast furnace slag. A high-speed mill was used for the mechanical activation. Chemical activation was used as the next step of activation. There are many materials that could be used, but in this study we used slaked lime and water-glass. Slaked lime had a positive effect on mechanical properties. Samples had higher compressive strength but the effect was limited only for 5 wt. %. Another used material was water-glass, but in this case, there was a significant negative effect. Compressive strength and flexural strength were significantly reduced.

Sign in / Sign up

Export Citation Format

Share Document