Effect of Intercritical Annealing on Structure and Mechanical Properties of 10GN2MFA Grade Steel

2007 ◽  
Vol 567-568 ◽  
pp. 377-380
Author(s):  
Ladislav Kander ◽  
Karel Matocha ◽  
Ales Korcak
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Treatment Process ◽  
Intercritical Annealing ◽  
Notch Toughness ◽  
Heat Treatment Process ◽  
Conventional Heat Treatment ◽  
Stress Relieving ◽  
The Impact ◽  
Grade Steel

The effect of intercritical annealing of 10GN2MFA grade steel on mechanical properties and impact notch toughness is studied in this paper. This type of low alloy banitic steel is used for production of collector bodies of steam generators for nuclear power station of VVER type. This article is focused on optimalization of fundamental utility properties and heat treatment process of the steel under investigation to increase toughness and critical temperature of brittleness. An intecritical annealing has been chosen as a useful tool for such improvement. Mechanical properties and impact notch toughness values after the intercritical annealing and conventional heat treatment regimes are compared. Effect of simulation of stress relieving including minimum and maximum allowable heating regimes are studied too. Intercritical annealing was added to the conventional quality heat treatment process, between quenching (normalizing) and tempering. The application of intercritical annealing improved the impact toughness significantly, an increase in the upper shelf energy and a decrease in transition temperature of steel under investigation.

Mechanical Properties of SiC/Gr Reinforced Hybrid Aluminum Composites after Heat Treatment

2021 ◽  
Vol 1042 ◽  
pp. 111-115
Author(s):  
Dwi Rahmalina ◽  
Hendri Sukma ◽  
Abdul Rokhim ◽  
Amin Suhadi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Matrix Composite ◽  
Treatment Process ◽  
Solution Treatment ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composite ◽  
Heat Treatment Process ◽  
Matrix Composites ◽  
The Impact

Metal matrix composite has been developed to improve mechanical properties for the automotive component application. One crucial factor in achieving excellent mechanical properties is improving the properties of the aluminum matrix of composite by the heat treatment process. The mechanical properties of Al-Mg-Si matrix composites alloyed with Zn and reinforced with 5% SiC and 5%Gr particle were examined after the heat treatment process. The aluminum matrix is melted inside the crucible furnace at 850 °C and is added with SiC/Gr particle, followed by stirring at 7500 rpm to optimize the mixing of the composite. Then, the composite is poured into the preheated mold at 300 °C and then squeezed with 30 MPa of pressure. The heat treatment process consists of three steps; solution treatment, quenching, and artificial aging. The aging process is conducted with variation of temperature (140 °C, 180 °C and 200 °C) and holding time (2, 4, and 6 hours). The test results show that the mechanical properties of aluminum matrix composite tend to increase after the heat treatment process. The optimum mechanical properties are achieved at the aging temperature of 200 °C for 6 hours, with the hardness value of 60.3 HRA and the impact value of 0.112 Joule/mm2.

Development of Wear Resistant Cast Steel and Its Study on Mechanical Properties

2013 ◽  
Vol 712-715 ◽  
pp. 98-101
Author(s):  
Hong Bo Li ◽  
Jing Wang ◽  
Han Chi Cheng ◽  
Chun Jie Li ◽  
Xing Jun Su
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Impact Toughness ◽  
Treatment Process ◽  
Cast Steel ◽  
Heat Treatment Process ◽  
Temperature Quenching ◽  
Quenching Temperature ◽  
High Toughness ◽  
The Impact

This paper mainly through the experimental study on the heat treatment process and mechanical properties of cast steel 35CrMnSiMo.According to the effect of alloy elements in design of a high-toughness abrasion-resistant cast steel, Cr, Mn, Si, as the main alloy elements, supplemented by a small amount of Mo, the casting molding, for hardness and impact toughness test of mechanical properties of experimental steel. The results show that, the as-cast 35CrMnSiMo by 880 °C, quenching for 20min then, the same quenching temperature, quenching hardness of materials is far greater than the oil quenching hardness. Water quenching hardness up to 25% higher than the oil quenching hardness, The impact toughness of specimen is inversely proportional to the contrast relationship Hardness.

Relationship of Microstructure and Mechanical Properties in Er-Containing Aluminum Alloy

2015 ◽  
Vol 1120-1121 ◽  
pp. 1109-1114
Author(s):  
Xin Lei ◽  
Hui Huang ◽  
S.P. Wen
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
Treatment Process ◽  
Mg Alloys ◽  
The Other ◽  
Heat Treatment Process ◽  
Comprehensive Performance ◽  
Relationship Of ◽  
Al Mg Alloys

This study investigated the mechanical properties and microstructures of Er-containing Al–Mg alloys. The research found that the H114-T sheet of Er-containing Al–Mg alloys showed a relative good comprehensive performance in mechanical properties. With the special rolling and heat treatment process, this H114-T sheet showed different morphology of microstructures with the other sheets in Er-containing Al–Mg alloys. Grains in H114-T sheet performed irregular shape polygon, a number of subgrains appeared in grains, the amount of dislocations in grains decreased. H114-T sheet possessed a lot of Copper texture, this may be one of important factors influenced the mechanical properties.

Study of Cu Addition on Precipitation Behaviors and Mechanical Properties in AA6082 Al-Mg-Si Alloy

2007 ◽  
Vol 546-549 ◽  
pp. 825-828 ◽  
Author(s):  
Man Jin ◽  
Jing Li ◽  
Guang Jie Shao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Thermal Stability ◽  
Treatment Process ◽  
Mechanical Tests ◽  
Age Hardening ◽  
Heat Treatment Process ◽  
Softening Process

The precipitation behaviors and microstructures of nano-precipitates in AA6082 Al-Mg-Si alloy with and without Cu additions during heat treatment process were studied using hardness measurements, TEM, mechanical tests and 3DAP. Meanwhile, the softening process of 6082 alloys with Cu and without Cu, isothermally conditioned at 250°C, has also been investigated. It was found that the rate of age hardening, mechanical properties and thermal stability are higher for the Cu-containing alloy. The TEM and 3DAP observations showed that Q’ precipitates were existed after aged at 170°C for 8h in the alloy with Cu addition. Comparing the hardness, mechanical properties and thermal stability curves, it was concluded that the Q’ precipitates play a major role in improving the age hardening kinetics and properties of 6082 alloy with Cu addition.

Effect of Heat Treatment Process on Mechanical Properties and Microstructure of S280

2021 ◽  
Vol 1035 ◽  
pp. 344-349
Author(s):  
Ye Qin Zhang ◽  
Ping Zhong ◽  
Huan Feng Li ◽  
Wen Qiang Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Treatment Process ◽  
Lath Martensite ◽  
Solution Temperature ◽  
Heat Treatment Process ◽  
Strengthening Phase ◽  
Optimal Heat Treatment ◽  
Precipitate Strengthening ◽  
Temperature Heating

The effect of solution temperature and aging temperature on mechanical properties and microstructure of the new ultrahigh strength stainless steel S280 was investigated by heat treatment process experiment. The results showed that the optimal heat treatment process was as follows: heating to 1080 °C，holding for a hour, and quenching in oil; cooling to -73 °C, holding for 2 hour, and warming in air to room temperature; heating to 540~550 °C, holding for 4 hour, and cooling in air. Choosing this heat treatment process, the steel can get good coordination between strength and toughness. Analyzed by HREM, the steel had desirable microstructures, which were fine lath martensite matrix with high density dislocation and finely dispersed precipitate strengthening phase, and film-like reversed austenite precipitated from the boundary of martensite.

scholarly journals Heat Treatment Effect on Mechanical Properties of 3D Printed Polymers

2019 ◽  
Vol 264 ◽  
pp. 02001 ◽  
Author(s):  
Eduardo de Avila ◽  
Jaeseok Eo ◽  
Jihye Kim ◽  
Namsoo P. Kim
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Treatment Effect ◽  
Biomedical Applications ◽  
Treatment Process ◽  
Heat Treatment Process ◽  
Post Heat Treatment ◽  
Intraocular Surgery ◽  
Osteoinductive Potential ◽  
3D Printed

PMMA, PC, and PEEK are thermoplastic polymers that possess favorable properties for biomedical applications. These polymers have been used in fields of maxillo-facial, orthopedic, intraocular surgery, and bio-implant, due to their excellent mechanical properties, osteoinductive potential, and antimicrobial capabilities. In this study, the effect of heat treatment on the mechanical properties of 3D printed polymers was characterized. By modifying printing temperature and post heat treatment process, the mechanical properties were specifically tailored for different applications, correlating with the properties of the implants that are commonly made using molding processes.

THE NEW HEAT TREATMENT TECHNOLOGY OF A356 ALUMINIUM ALLOY PREPARED BY PTC

2009 ◽  
Vol 23 (06n07) ◽  
pp. 906-913 ◽  
Author(s):  
LIANYONG ZHANG ◽  
YANHUA JIANG ◽  
ZHUANG MA ◽  
WENKUI WANG
Keyword(s):  
Electron Microscopy ◽  
Phase Transition ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Treatment Process ◽  
A356 Alloy ◽  
Heat Treatment Process ◽  
X Rays ◽  
Treatment Technology ◽  
Conventional Heat Treatment

Phase Transition Cooling (PTC), using the absorbed latent heat during the melting of phase transition cooling medium to cool and solidify alloys in the process of casting, is a new casting technology. Specimens of A356 casting aluminum alloy were prepared by this method in the paper. The new heat treatment process (cast and then aging directly without solid solution) of A356 alloy was performed. For comparison, the conventional T6 heat treatment (solution and then aging treatment) was performed too. The mechanical properties of A356 alloy with different heat treatments were measured by tensile strength testing methods and microstructures of the alloy with different heat treatment process were investigated by optical microscopy (OM), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), X-rays diffraction (XRD) and transmission electron microscopy (TEM) too. The results show that ultimate tensile strength (UTS) of A356 alloy with the new heat treatment process is much higher than that with conventional heat treatment while the elongations with the two heat treatment processes are very close. This is due to the grain refinement obtained after PTC processing.

The influence of heat treatment process on mechanical properties of surface treated volcanic ash particles/polyphenylene sulfide composites

2016 ◽  
Vol 39 (5) ◽  
pp. 1604-1611 ◽  
Author(s):  
Mustafa Özgür Bora ◽  
Onur Çoban ◽  
Togayhan Kutluk ◽  
Sinan Fidan ◽  
Tamer Sinmazçe˙lk
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Volcanic Ash ◽  
Treatment Process ◽  
Polyphenylene Sulfide ◽  
Heat Treatment Process

Numerical Simulation of the H-Beam during Cooling Process

2013 ◽  
Vol 310 ◽  
pp. 145-149 ◽  
Author(s):  
Jian Liu ◽  
Fu Zeng Hou ◽  
Xiao Guang Yu
Keyword(s):  
Mechanical Properties ◽  
Numerical Simulation ◽  
Heat Treatment ◽  
Theoretical Basis ◽  
Treatment Process ◽  
Residual Austenite ◽  
Heat Treatment Process ◽  
Cooling Process ◽  
Controlled Cooling ◽  
H Beam

In order to improve the comprehensive mechanical properties of the steel, the heat treatment software COSMAP is used to simulate the rolling and controlled cooling of H-beam. The numerical simulation shows that the mechanical properties of controlled cooling can be obviously improved, when the cooling rate is controlled at 10°C/s around. Strength and hardness can be improved under the condition of ductility and toughness ensured. Meanwhile the amount of residual austenite can be reduced significantly. It provides a theoretical basis for further optimization of the heat treatment process.

Machine Design for Multiscale Nitinol Annealment Process and End Product Performance Analysis

2020 ◽  
Author(s):  
Amanda Skalitzky ◽  
Stuart Coats ◽  
Ramsis Farag ◽  
Austin Gurley ◽  
David Beale
Keyword(s):  
Heat Treatment ◽  
Treatment Process ◽  
Heat Treating ◽  
Experimental Results ◽  
Heat Treatment Process ◽  
Scanning Calorimetry ◽  
Niti Wire ◽  
Annealing Temperatures ◽  
Conventional Heat Treatment ◽  
Post Production

Abstract The functional properties of Nitinol (NiTi) are set by composition, production process, and post-production heat treatment and cold working. Post-production heat treating is dependent on two main parameters: anneal temperature and aging time. Most heat-treating processes performed by researchers generally consist of simple temperature soaks at specified aging times. However, there are drawbacks to this method. More complex heat treatments can result in performance improvements, but they are difficult to implement and often proprietary to manufacturers and therefore not widely used by researchers. By designing a Continuously-Fed heat treatment System (CFS), this work demystifies this complex heat-treatment process by rapidly heat-treating NiTi wire samples across a range of annealing temperatures, soak times, and tensions with little human intervention. This automated process ensures samples are created in a consistent manner and results in a much more consistent end-product when compared to conventional heat-treating methods. Using the CFS, a gamut of samples with varying annealing temperatures (400–550°C) and aging times (1–3 minutes) were created with 0.25mm diameter high-temperature actuator wire initially in the ‘as-drawn’ condition. Differential Scanning Calorimetry (DSC) analysis was performed to determine how the transition temperature(s) change with the various heat-treating parameters and the mechanical properties of the wire were determined utilizing a tensile test. The experimental results demonstrate the benefits of the CFS and are compared to those of a more conventional heat treatment process. Experimental results show that high-performance Nitinol actuator behavior can consistently be achieved using the CFS. Optimal heat treatment processes can be determined quickly experimentally.

Sign in / Sign up

Export Citation Format

Share Document