scholarly journals Characterisation of the Mural Paintings from the Misericordia Church of Odemira (Portugal)

2008 ◽  
Vol 587-588 ◽  
pp. 1019-1023
Author(s):  
Sara Valadas ◽  
Deolinda Tavares ◽  
João Coroado ◽  
António Santos Silva ◽  
Jorge Pedro ◽  
...  
Keyword(s):  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Thermogravimetric Analysis ◽  
Chemical Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Mural Paintings ◽  
Microchemical Analysis ◽  
Lime Mortars ◽  
Local Sources

Several mortars from mural paintings were collected from the Misericórdia Church of Odemira and analysed by using different techniques namely X-ray diffraction, thermogravimetric analysis with differential thermal analysis, SEM-EDX, optical microscopy, CHNS elemental analysis and chemical analysis. Microfragments of paint layers were collected and analysed by microchemical analysis. The results showed that the mortars are aerial lime mortars with siliceous aggregates and that the pigments used were mainly pigments from local sources (red and yellow ochre’s and malachite) and small blue.

Purification of Bentonite Clays from Cubati, PB, Brazil, for Diversified Applications

2014 ◽  
Vol 805 ◽  
pp. 486-491
Author(s):  
J.M.R. Figueirêdo ◽  
Juliana Melo Cartaxo ◽  
I.A. Silva ◽  
C.D. Silva ◽  
Gelmires Araújo Neves ◽  
...  
Keyword(s):  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Chemical Analysis ◽  
Laser Diffraction ◽  
The State ◽  
X Ray Diffraction ◽  
X Ray ◽  
Granulometric Analysis ◽  
Bentonite Clays

The State of Paraíba, Brazil, retains about 88.5% of all Brazilian bentonite, and much of this production comes from deposits in the District of Boa Vista, PB. Nevertheless, the deposits are almost depleted. Recently, new deposits were found, which will increases the reserves of the State, in the regions of Cubati and Pedra Lavrada, PB. The objective of this work is to characterize and develop purified clays, through sieving and hydrocycloning techniques, from those recently discovered bentonites for several applications. The characterization of the sample was done through granulometric analysis by laser diffraction, X-ray diffraction, chemical analysis by X-ray fluorescence, and thermogravimetric and differential thermal analysis. The results show that the samples are typical of bentonite clays, and that the purification solely by hydrocyclone presents the best results.

Sepiolite at a locality in the Keuper Marl of the Midlands

1956 ◽  
Vol 31 (235) ◽  
pp. 328-332 ◽  
Author(s):  
P. S. Keeling
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Chemical Analysis ◽  
Diffraction Data ◽  
Ferric Oxide ◽  
X Ray Diffraction ◽  
X Ray

SummarySepiolite has been identified in the Keuper Marl at a Midlands locality by X-ray diffraction data, electron microscopy, differential thermal analysis, and chemical analysis. It has been calculated that a sample representing 30 ft. thickness of clay may contain as much as 39 % sepiolite. Apart from sepiolite, the Keuper Marl in the area examined consists mainly of mica, quartz, calcite, and ferric oxide.

ADSORPTION OF CYCLOHEXANE AND BENZENE ON MIXED HYDROXIDES AND OXIDES OF MAGNESIUM AND ALUMINIUM

1966 ◽  
Vol 44 (8) ◽  
pp. 877-884 ◽  
Author(s):  
R. I. Razouk ◽  
Sh. Nashed ◽  
F. N. Antonious
Keyword(s):  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Thermogravimetric Analysis ◽  
Surface Area ◽  
Structural Changes ◽  
Mixed Oxides ◽  
X Ray Diffraction ◽  
Oxide Systems ◽  
X Ray ◽  
Characteristic Lines

Seven mixed hydroxides of magnesium and aluminium were prepared, and phase and structural changes accompanying their dehydration were investigated by differential thermal analysis, thermogravimetric analysis, and X-ray diffraction techniques. The differential thermal analysis curves possess 2 peaks corresponding to those of parent hydroxides together with a new peak, and the thermogravimetric analysis curves show slight inflections. X-ray diffraction patterns of the mixed hydroxides possess the characteristic lines of the parent hydroxides together with three to five new intense lines which might indicate the formation of a double hydroxide. When the mixed hydroxides are progressively heated they give rise to products possessing patterns which first become diffuse and ultimately pass mainly into the spinel pattern.Adsorption isotherms of cyclohexane and benzene were measured on the mixed hydroxides and their dehydration products. Specific surface areas calculated by the application of the Brunauer, Emmett, Teller (B.E.T.) equation are in general in good agreement for the two adsorbates. The surface area increases with rise of dehydration temperature to a maximum at 500–600 °C and then decreases with further rise in temperature. This behavior is common to crystalline oxide systems and may be ascribed to the intermingling of decomposition, re-crystallization, and sintering processes. Variations in the molecular ratio of the mixed oxides (as much as 20-fold), and in the method of preparation, do not much alter the surface area.

The Effect of H3BO3 Microaddition on Microstructure of Ni/MgO Sintered Compact by Co-Precipitation Method

2013 ◽  
Vol 750 ◽  
pp. 168-171
Author(s):  
Ning Ning Zhou ◽  
Dong Ying Ju ◽  
Wan Yu Ding
Keyword(s):  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Thermogravimetric Analysis ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Sintered Compact ◽  
X Ray ◽  
Sintered Powder ◽  
Co2 Flow ◽  
Co Precipitation

In the present work, Ni/MgO powder was prepared by co-precipitation in which CO restore NiO to elemental subtance Ni due to C2O42- was decompose to CO and CO2 at 700°C. As the process of the second sintering, H3BO3 was added into the sintered powder of 700°C and was grinded. Then the powder of H3BO3 added was sintered at 800°C，so that the powder was refined, obviously. Thermogravimetric analysis (TGA) and differential thermal analysis(DTA) was carried out in CO2 flow at 10°C/min. X-ray diffraction (XRD) was carried out on a X-ray diffractometer operated at 20KV and 40mA. The microstructures and morphologies were studied by EPMA and XPS.

scholarly journals The products of selenite hydrothermal treatment in lithium chloride solutions

2000 ◽  
Vol 65 (4) ◽  
pp. 265-274
Author(s):  
Slobodanka Marinkovic ◽  
Aleksandra Kostic-Pulek ◽  
Mirjana Djuricic
Keyword(s):  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Thermogravimetric Analysis ◽  
Microscopic Examination ◽  
Atmospheric Pressure ◽  
Calcium Sulphate ◽  
Infrared Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Calcium Sulphate Hemihydrate

Selenite was boiled in LiCl solutions of different concentrations (1 M, 2 M, 3 M, 4 M and 5M) at the respective boiling temperatures and atmospheric pressure. The products were subjected to X-ray diffraction analysis, qualitative infrared analysis, differential thermal analysis, thermogravimetric analysis and microscopic examination. The product obtained in the 1 M LiCl solution was the ?-form of calcium sulphate hemihydrate (?-CaSO4.0.5H2O). In more concentrated LiCl solutons, 2M and 3 M, the ?-form of calcium sulphate hemihydrate (?-CaSO4.0.5H2O) was formed. The product obtained in the 4MLiCl solution was also the ?-form of calcium sulphate hemihydrate, only mixed with the ?-form of calcium sulphate (?-CaSO4). Finally, in the 5 M LiCl solution the ?-form of calcium sulphate or ?-anhydrite was formed.

Identification and Thermal Stability of Copper(I) Sulfate

1972 ◽  
Vol 50 (23) ◽  
pp. 3872-3875 ◽  
Author(s):  
Kim Vo Van ◽  
Fathi Habashi
Keyword(s):  
Thermal Stability ◽  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Thermogravimetric Analysis ◽  
Diffraction Pattern ◽  
Chemical Processes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Thermal Stability Of

Anhydrous CU2SO4 was prepared and its X-ray diffraction pattern was established. Differential thermal analysis, thermogravimetric analysis, and X-ray diffraction methods were used to study the effect of heating in different atmospheres. The formation of CU2SO4 as an intermediate in chemical processes has been discussed.

PENINGKATAN LAJU DISOLUSI ACYCLOVIR DENGAN METODE SISTEM DISPERSI PADAT MENGGUNAKAN POLOXAMER 188

2016 ◽  
Vol 5 (1) ◽  
pp. 6
Author(s):  
Budi Setiawan ◽  
Erizal Zaini ◽  
Salman Umar
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Differential Thermal Analysis ◽  
Fourier Transform Infrared ◽  
X Ray Diffraction ◽  
Poloxamer 188 ◽  
X Ray ◽  
Scanning Electron

Sebuah penelitian tentang sistem dispersi padat dari asiklovir dengan poloxamer 188 telah dilakukan formulasi dengan pencampuran secara fisika dengan rasio 1 : 1, 1 : 3, 1 : 5 dan dispersi padat 1 : 1, 1 : 3, 1 : 5 dan penggilingan 1:1 sebagai pembanding. Dispersi padat dibuat menggunakan metode pencairan (fusi), yang digabung dengan poloxamer 188 pada hotplate kemudian asiklovir dimasukkan ke dalam hasil poloxamer 188 lalu di kocok hingga membentuk masa homogen. Semua formula yang terbentuk termasuk asiklovir poloxamer 188 murni dianalisis karakterisasinya dengan Differential Thermal Analysis (DTA), X-ray Diffraction, Scanning Electron Microscopy (SEM), dan Fourier Transform Infrared (FTIR), kemudian pengambilan dilakukan  (penentuan kadar) mengunakan spektrofotometer UV pada panjang gelombang 257,08 nm dan uji laju disolusi dengan aquadest bebas CO2 menggunakan metode dayung. Hasil pengambilan  (penentuan kadar) menunjukkan bahwa semua formula memenuhi persyaratan farmakope Amerika edisi 30 dan farmakope Indonesia edisi 4 yaitu 95-110%. Sedangkan hasil uji laju disolusi untuk campuran fisik 1: 1, dan dispersi padat 1: 1, dan penggilingan 1: 1 menunjukkan peningkatan yang nyata dibandingkan asiklovir murni. Hal ini juga dapat dilihat dari hasil perhitungan statistik  menggunakan analisis varian satu arah  SPSS 17.

scholarly journals The Potential for Natural Stones from Northeastern Brazil to Be Used in Civil Construction

Minerals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 440
Author(s):  
Fabiana Pereira da Costa ◽  
Jucielle Veras Fernandes ◽  
Luiz Ronaldo Lisboa de Melo ◽  
Alisson Mendes Rodrigues ◽  
Romualdo Rodrigues Menezes ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Chemical Resistance ◽  
Mechanical Analysis ◽  
Northeastern Brazil ◽  
X Ray Diffraction ◽  
X Ray ◽  
Chemical Agents ◽  
Natural Stones

Natural stones (limestones, granites, and marble) from mines located in northeastern Brazil were investigated to discover their potential for use in civil construction. The natural stones were characterized by chemical analysis, X-ray diffraction, differential thermal analysis, and optical microscopy. The physical-mechanical properties (apparent density, porosity, water absorption, compressive and flexural strength, impact, and abrasion) and chemical resistance properties were also evaluated. The results of the physical-mechanical analysis indicated that the natural stones investigated have the potential to be used in different environments (interior, exterior), taking into account factors such as people’s circulation and exposure to chemical agents.

The Roman Ceramics of Salobrena (Granada-Spain) and their Raw Materials

1992 ◽  
Vol 267 ◽  
Author(s):  
Ana M De Andres ◽  
Isabel MuÑOZ
Keyword(s):  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Raw Materials ◽  
Third Century ◽  
Western Coast ◽  
X Ray Diffraction ◽  
X Ray ◽  
The Third ◽  
Good Number ◽  
Scanning Electron

ABSTRACTNineteen roman ceramic sherds found near Salobreña (Granada, Spain), in the western coast of the Mediterranean Sea, as well as different ceramic clays from the surroundingsare studied. Both clays and ceramic sherds are characterizad by X-ray diffraction and spectrometry, differential thermal analysis, and scanning electron and optical microscopies. A good number of the ceramic pieces, among which some “Terrae Sigillatae”, have a composition similar to that of the local clays and, thus, have been probably manufactured at Salobreña. Only a few of them have a foreign origin. For most of them, the firing temperature was about 800-850 °C, although some have been produced at 900-1000 °C, and some others at 1000-1100 °C. It is concluded that Salobreña appearsto have been an important settlement just in the third century of the Christian era.

scholarly journals Silica-Kaolin Mix Effect on Evaporative Pattern Castings Surface Roughness

2016 ◽  
Vol 16 (3) ◽  
pp. 83-88 ◽  
Author(s):  
B.V. Omidiji ◽  
R.H. Khan ◽  
M.S. Abolarin
Keyword(s):  
Thermal Analysis ◽  
Surface Roughness ◽  
Differential Thermal Analysis ◽  
Ratio Method ◽  
Gating System ◽  
X Ray Diffraction ◽  
Pouring Temperature ◽  
Material Loss ◽  
Refractory Coating ◽  
X Ray

Abstract The influence of the refractory coating which is a mixture of silica flour and kaolin on the surface roughness of the plate castings produced using evaporative patterns had been considered in this work. The kaolin was used as a binder and ratio method was employed to form basis for the factorial design of experiment which led to nine runs of experiments. Methyl alcohol at 99% concentration was used as the carrier for the transfer of the coating to the surface of the patterns. Pouring temperature was observed as a process parameter alongside the mix ratios of the coating. Attempts were made to characterize the refractory coating by using two methods; differential thermal analysis (DTA) and X-ray diffraction. Attempt was also made to characterize the casting material. Gating system design was done for the plate casting to determine the correct proportions of the gating parameters in order to construct the gating system properly to avoid turbulence during pouring of liquid metal. A digital profilometer was used to take the measurements of the surface roughness. It was observed that the mix ratio 90% silica flour-10% kaolin produced the lowest value of the surface roughness of the plate castings and had the lowest material loss in the DTA test. The pouring temperature of 650°C produced best casting.

Sign in / Sign up

Export Citation Format

Share Document