Utilization of Color Metallography in Characterization of a Modified SAE 4118H Steel Submitted to Isothermal Treatments

2014 ◽  
Vol 805 ◽  
pp. 242-247
Author(s):  
Selauco Vurobi ◽  
Thiago Ferreira de Andrade ◽  
Osvaldo Mitsuyuki Cintho
Keyword(s):  
Constant Temperature ◽  
Volume Fraction ◽  
Treatment Temperature ◽  
Isothermal Treatment ◽  
Isothermal Decomposition ◽  
Bainitic Microstructure ◽  
Metallographic Preparation ◽  
Color Metallography

A modified SAE 4118H steel was subjected to isothermal treatments between 700 °C and 400 oC every 50 °C range, with the intention of evaluating the decomposition of austenite at constant temperature. It was varied time of stay in the isothermal treatment between 15 and 28800 seconds depending on the treatment temperature. After each isothermal treatment and standard metallographic preparation, the samples were etched with color metallography reagents for revealing the microstructure obtained. At temperatures of 700oC to 550°C the steel showed microstructure composed of ferrite and pearlite. Between 500oC and 400°C bainitic microstructure was quickly formed. The reduction of treatment temperature provided finer microstructures, which increased the hardness of steel. With the use of color metallography reagents, excellent contrast for determining the volume fraction of microstructural constituents formed isothermally was obtained, helping the study of isothermal decomposition of austenite.

scholarly journals Characterization of the Microstructure Evolution of Ni-Based Superalloy at Liquidus Temperature by Electromagnetic Field

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 748
Author(s):  
Zhongtang Gao ◽  
Jinqiang Tan ◽  
Wei Guo ◽  
Chuanwei Zhang ◽  
Wu Zhang
Keyword(s):  
Electromagnetic Field ◽  
Volume Fraction ◽  
Treatment Time ◽  
Treatment Temperature ◽  
Isothermal Treatment ◽  
Uniform Temperature ◽  
Melt Treatment ◽  
Average Grain Size ◽  
Equiaxed Grains

The effect of isothermal treatment temperatures and isothermal treatment time on the microstructure was studied. The results showed that the globular and equiaxed grains with the average grain size of 60 μm and the shape factor of circle of 0.95 can be obtained when the melt of Ni-Cr-W superalloy was subjected to the heat treatment of 10 min at 1400 °C. The quenching results showed the volume fraction of the eutectic phase was the largest and the volume fraction of primary γ phase was the smallest after the isothermal treatment of 1400 °C. The optimal melt treatment temperature and time were 1400 °C and 10 min, respectively. Moreover, the effect of electromagnetic field on the solidification was also investigated. It was demonstrated that applying electromagnetic field was beneficial to the uniform temperature, solute field and the high density of the secondary nuclei, which contributed to grain refinement.

Color Metallography and Electron Microscopy Techniques Applied to the Characterization of 413.0 Aluminum Alloys

2013 ◽  
Vol 19 (4) ◽  
pp. 1019-1026 ◽  
Author(s):  
George Vander Voort ◽  
Juan Asensio-Lozano ◽  
Beatriz Suárez-Peña
Keyword(s):  
Electron Microscopy ◽  
High Pressure ◽  
Volume Fraction ◽  
Microstructural Analysis ◽  
Polarized Light ◽  
Eutectic Si ◽  
Color Metallography ◽  
Microscopy Techniques ◽  
Optical Color

AbstractThe influence on alloy 413.0 of the refinement and modification of its microstructure was analyzed by means of several microscopy techniques, as well as the effect of the application of high pressure during solidification. For each treatment and solidification pressure condition employed, the most suitable microscopy techniques for identifying and characterizing the phases present were investigated. Color metallography and electron microscopy techniques were applied to the qualitative microstructural analysis. Volume fraction and grain size of the primary α-Al were characterized by quantitative metallographic techniques. The results show that the effect caused by applying high pressure during solidification of the alloy is more pronounced than that caused by modification and refinement of the microstructure when it solidifies at atmospheric pressure. Furthermore, it has been shown that, for Al–Si alloy characterization, when aiming to characterize the primary α-Al phase, optical color metallography observed under crossed polarized light plus a sensitive tint filter is the most suitable technique. When the goal is to characterize the eutectic Si, the use of optical color metallography or electron microscopy is equally valid. The characterization of iron-rich intermetallic compounds should preferably be performed by means of backscattered electron imaging.

scholarly journals Color-Metallographic Characterization of Alloyed White Cast Irons Ni-Hard Type

Metals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 728
Author(s):  
Milagrosa González Fernández de Castro ◽  
Yolanda Martín Álvarez ◽  
Juan José Moreno-Labella ◽  
Miguel Panizo-Laiz ◽  
Benito del Río
Keyword(s):  
Impact Resistance ◽  
Solidification Structure ◽  
Hard Alloys ◽  
Metallic Materials ◽  
Low Carbon ◽  
Cast Irons ◽  
The Family ◽  
Color Metallography ◽  
Hard Type

The Ni-hard alloys white-cast irons are generally used for high wear work. Among them, those with better impact resistance because of its low carbon content compared to the rest of the family, are studied in this paper. One experimental technique of characterizing the metallic materials is the microstructural study. Several metallographic attacks intended to reveal qualitatively each microconstituent that forms the alloy, as well as the segregation and solidification structure of casting, are studied in this article. The use of color metallography is fundamental in this case to distinguish clearly the microconstituents. The main objective of this paper is to propose a series of attacks that identify each one of the microconstituents present in the alloy that has not been reported up to date.

Magnetic Characterization of SUS316L Deformed by High Pressure Torsion

2011 ◽  
Vol 239-242 ◽  
pp. 1300-1303
Author(s):  
Hong Cai Wang ◽  
Minoru Umemoto ◽  
Innocent Shuro ◽  
Yoshikazu Todaka ◽  
Ho Hung Kuo
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Stainless Steel ◽  
Phase Transformation ◽  
Austenitic Stainless Steel ◽  
Volume Fraction ◽  
High Pressure Torsion ◽  
Austenitic Matrix ◽  
Magnetic Characterization

SUS316L austenitic stainless steel was subjected to severe plastic deformation (SPD) by the method of high pressure torsion (HPT). From a fully austenitic matrix (γ), HPT resulted in phase transformation from g®a¢. The largest volume fraction of 70% a¢ was obtained at 0.2 revolutions per minute (rpm) while was limited to 3% at 5rpm. Pre-straining of g by HPT at 5rpm decreases the volume fraction of a¢ obtained by HPT at 0.2rpm. By HPT at 5rpm, a¢®g reverse transformation was observed for a¢ produced by HPT at 0.2rpm.

A Novel Processing Route for the Fabrication of Monolithic and Composite Silicon Nitride

1992 ◽  
Vol 287 ◽  
Author(s):  
R. V. Raman ◽  
S. V. Rele
Keyword(s):  
Volume Fraction ◽  
Hot Isostatic Pressing ◽  
Thermal Exposure ◽  
Processing Route ◽  
Promising Alternative ◽  
Α Phase ◽  
Key Issues ◽  
Novel Processing ◽  
Composite Silicon

ABSTRACTCurrent hot isostatic consolidation methodology used for the fabrication of complex-shaped Si3N4-based components requires the use of an expensive glass encapsulation technique and extended thermal exposure (in hours) of the specimen. An alternative consolidation approach involving the use of solid pressure transmitting media under high pressure, has enabled the consolidation of Si3N4 alloys without the need for glass encapsulation.Characterization of microstructures and mechanical properties of this (MOR, fracture toughness) material has been carried out and will be presented. It has been noted that in Si 3N4/8%Y2O3-4%Al2O3 composition, consolidated using this approach, a significantly larger volume fraction of α phase has been retained compared with typically observed conversion in α⇒ β in hot isostatically pressed material or sintered material.Key issues for addressing densification and microstructure control using this process are presented. This rapid consolidation approach appears to be a promising alternative to hot isostatic pressing for the fabrication of complex-shaped Si3N4 components.

Estimation of Interlayer Thickness in Inorganic Particulate-Filled Polymer Composites

2011 ◽  
Vol 24 (6) ◽  
pp. 777-788 ◽  
Author(s):  
J.Z. Liang
Keyword(s):  
Polymer Composites ◽  
Volume Fraction ◽  
Particle Diameter ◽  
Interfacial Structure ◽  
Interlayer Thickness ◽  
Filled Polymer ◽  
Mechanical And Physical Properties ◽  
The Relationship ◽  
Good Agreement

The structure of the interlayer between matrix and inclusions affect directly the mechanical and physical properties of inorganic particulate-filled polymer composites. The interlayer thickness is an important parameter for characterization of the interfacial structure. The effects of the interlayer between the filler particles and matrix on the mechanical properties of polymer composites were analyzed in this article. On the basis of a simplified model of interlayer, an expression for estimating the interlayer thickness ([Formula: see text]) was proposed. In addition, the relationship between the [Formula: see text] and the particle size and its concentration was discussed. The results showed that the calculations of the [Formula: see text] and thickness/particle diameter ratio ([Formula: see text]) increased nonlinearly with an increase of the volume fraction of the inclusions. Moreover, the predictions of [Formula: see text] and the relevant data reported in literature were compared, and good agreement was found between them.

METALLURGICAL AND CORROSION CHARACTERIZATION OF POST WELD HEAT TREATED DUPLEX STAINLESS STEEL (UNS S31803) JOINTS BY FRICTION WELDING PROCESS

2016 ◽  
Vol 23 (03) ◽  
pp. 1650013 ◽  
Author(s):  
MOHAMMED ASIF M. ◽  
KULKARNI ANUP SHRIKRISHNA ◽  
P. SATHIYA
Keyword(s):  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Friction Welding ◽  
Volume Fraction ◽  
Welding Process ◽  
Equilibrium Temperature ◽  
Weld Interface ◽  
Heat Treated ◽  
Weld Heat

The present study focuses on the metallurgical and corrosion characterization of post weld heat treated duplex stainless steel joints. After friction welding, it was confirmed that there is an increase in ferrite content at weld interface due to dynamic recrystallization. This caused the weldments prone to pitting corrosion attack. Hence the post weld heat treatments were performed at three temperatures 1080[Formula: see text]C, 1150[Formula: see text]C and 1200[Formula: see text]C with 15[Formula: see text]min of aging time. This was followed by water and oil quenching. The volume fraction of ferrite to austenite ratio was balanced and highest pit nucleation resistance were achieved after PWHT at 1080[Formula: see text]C followed by water quench and at 1150[Formula: see text]C followed by oil quench. This had happened exactly at parameter set containing heating pressure (HP):40 heating time (HT):4 upsetting pressure (UP):80 upsetting time (UP):2 (experiment no. 5). Dual phase presence and absence of precipitates were conformed through TEM which follow Kurdjumov–Sachs relationship. PREN of ferrite was decreasing with increase in temperature and that of austenite increased. The equilibrium temperature for water quenching was around 1100[Formula: see text]C and that for oil quenching was around 1140[Formula: see text]C. The pit depths were found to be in the range of 100[Formula: see text]nm and width of 1.5–2[Formula: see text][Formula: see text]m.

Sign in / Sign up

Export Citation Format

Share Document