Wear Resistance Improvement by Nanostructured Surface Layer Produced by Burnishing

2018 ◽  
Vol 917 ◽  
pp. 231-235 ◽  
Author(s):  
Hirotaka Kato ◽  
Hiroto Ueki ◽  
Keitaro Yamamoto ◽  
Kazufumi Yasunaga
Keyword(s):  
Wear Resistance ◽  
Surface Layer ◽  
Carbon Steel ◽  
Rotating Disk ◽  
Dry Sliding Wear ◽  
Wear Properties ◽  
Surface Layers ◽  
Wear Rates ◽  
Strain And Strain Rate ◽  
Burnishing Process

Burnishing, which is one of the most powerful processes for microstructural evolution, was performed by a cemented carbide ball (6 mm in diameter) that was loaded and fed on the flat surface of a rotating disk specimen of carbon steel using a lathe machine. The effects of burnishing process parameters such as force and rotation speed on the surface roughness, microstructure and hardness were investigated. In addition the dry sliding wear properties of the burnished surface layers were studied using a ball-on-disk friction method. It was found that the burnished surface was much smoother than as-turned surface (before burnishing) owing to the plastic flow of the surface asperities through the rubbing motion of the burnishing ball. Nanostructure in the 30 - 50 nm grain size range was formed in the burnished sub-surface layer, and the hardness significantly increased due to the grain refinement. The nanocrystalline microstructure was observed at high burnishing forces and speeds owing to the high strain and strain rate of the friction-induced plastic deformation. Moreover the burnishing process reduced the specific wear rates by a factor of six. Thus we concluded that the wear resistance of carbon steel can be significantly improved by burnishing due to the smooth surface and nanostructured sub-surface layers.

Dry Sliding Wear of Lu2O3 Sialon Ceramics

2006 ◽  
Vol 317-318 ◽  
pp. 351-354
Author(s):  
Mark I. Jones ◽  
Kiyoshi Hirao ◽  
Hideki Hyuga ◽  
Yukihiko Yamauchi
Keyword(s):  
Wear Resistance ◽  
Composite Materials ◽  
Wear Mechanism ◽  
Wear Behaviour ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Wear Properties ◽  
Experimental Conditions ◽  
Wear Rates ◽  
Order Of Magnitude

The effects of microstructure and composition on the wear properties of Lu sialon ceramics have been studied under dry sliding conditions through block-on-ring wear tests. Microstructural and compositional effects on wear behaviour were studied by producing both equiaxed and elongated α sialons through the incorporation of additional oxides to promote extended liquid formation and grain growth, and by producing α / β composite materials with elongated β grains. The wear response of the materials is discussed in terms of the dominant wear mechanism under different experimental conditions. Under higher loads, where fracture dominates, materials with improved mechanical properties show better wear resistance and both the composite materials and the elongated α sialons showed lower wear rates than the equiaxed materials due to the elongated grain microstructures. Under low normal loads, fracture does not occur and the dominant wear mechanism is thought to be tribochemically assisted wear. Under these conditions, the equiaxed materials had better wear resistance than the composites, and the Lu-α sialon showed an order of magnitude lower wear rate than an equivalent Y-α sialon, thought to be due to better oxidation resistance and improved refractory nature afforded through the use of the smaller radius cation. The elongated Lu-α sialons under these low load conditions showed wear resistance that was to some extent dependent on the composition of the additional liquid phase, with high SiO2 contents leading to higher wear rates.

The Influence of Yttrium Rich Intermetallic Phases and Heat Treatment on the Microstructure, Hardness and Wear Properties of Al-15%Mg2Si Composite

2011 ◽  
Vol 471-472 ◽  
pp. 1165-1170 ◽  
Author(s):  
H.R. Jafari Nodooshan ◽  
M. Emamy ◽  
N. Nemati ◽  
A. Bahrami
Keyword(s):  
Heat Treatment ◽  
Wear Resistance ◽  
Wear Behavior ◽  
Hardness Measurement ◽  
Intermetallic Phases ◽  
Track Length ◽  
Dry Sliding Wear ◽  
Wear Properties ◽  
Wear Rates ◽  
Before And After

This study was undertaken to investigate the effect of different concentrations of Yttrium (0.1, 0.3, 0.5, 1.0 wt.%) and heat treatment on the microstructure, hardness and wear resistance of an in-situ cast composite (Al-15%Mg2Si ). The microstructural study of the composite before and after solution and ageing showed both primary and secondary Mg2Si phases in all specimens and intermetallics containing Y (Al2Y) were visible after Solution at 520 °C for 4 hours. Hardness measurement demonstrates that the addition of Y increases the hardness gradually but a reduction in the hardness of heat treated specimen’s occurs with the addition of Y ( 0.5%Y).Wear tests were performed using a pin on disk apparatus. The MMCs were rubbed against a carbon steel pin under a load of 10 and 20 N at a sliding velocity of 0.1 ms−1; track length of 1500 m. The degree of improvement in dry sliding wear resistance brought about by Y addition is strongly dependent on the formation of Yttrium rich intermetallic phases as well as heat treatment influence and the wear behavior determined through the precise measurement of weight loss of the samples and wear rates. Worn surfaces were analyzed by scanning electron microscopy (SEM).

Influence of Multiwall Carbon Nanotube on mechanical and wear properties of Copper – Iron composite

2020 ◽  
Vol 17 (1) ◽  
pp. 7570-7576 ◽  
Author(s):  
H. Sh. Hammood ◽  
S. S. Irhayyim ◽  
A. Y. Awad ◽  
H. A. Abdulhadi
Keyword(s):  
Carbon Nanotubes ◽  
Volume Fraction ◽  
Hybrid Composites ◽  
Hydraulic Press ◽  
Dry Sliding Wear ◽  
Multiwall Carbon Nanotube ◽  
Wear Properties ◽  
Sem Images ◽  
Wear Rates ◽  
Multiwall Carbon

Multiwall Carbon nanotubes (MWCNTs) are frequently attractive due to their novel physical and chemical characteristics, as well as their larger aspect ratio and higher conductivity. Therefore, MWCNTs can allow tremendous possibilities for the improvement of the necessarily unique composite materials system. The present work deals with the fabrication of Cu-Fe/CNTs hybrid composites manufactured by powder metallurgy techniques. Copper powder with 10 vol. % of iron powder and different volume fractions of Multi-Wall Carbon Nanotubes (MWCNTs) were mixed to get hybrid composites. The hybrid composites were fabricated by adding 0.3, 0.6, 0.9, and 1.2 vol.% of MWCNTs to Cu- 10% Fe mixture using a mechanical mixer. The samples were compressed under a load of 700 MPa using a hydraulic press to compact the samples. Sintering was done at 900°C for 2 h at 5ºC/min heating rate. The microscopic structure was studied using a Scanning Electron Microscope (SEM). The effect of CNTs on the mechanical and wear properties, such as micro-hardness, dry sliding wear, density, and porosity were studied in detail. The wear tests were carried out at a fixed time of 20 minutes while the applied loads were varied (5, 10, 15, and 20 N). SEM images revealed that CNTs were uniformly distributed with relative agglomeration within the Cu/Fe matrix. The results showed that the hardness, density, and wear rates decreased while the percentage of porosity increased with increasing the CNT volume fraction. Furthermore, the wear rate for all the CNTs contents increased with the applied load.

Process optimization using grey relational analysis in dry sliding wear behavior on SiC/B4C/Talc reinforced Al 6061 hybrid metal matrix composite

2021 ◽  
Vol 118 (6) ◽  
pp. 614
Author(s):  
Chellamuthu Ramesh Kumar ◽  
Subramanian Baskar ◽  
Ganesan Ramesh ◽  
Pathinettampadian Gurusamy ◽  
Thirupathy Maridurai
Keyword(s):  
Wear Resistance ◽  
Metal Matrix ◽  
Wear Behavior ◽  
Base Alloy ◽  
Specific Weight ◽  
Dry Sliding Wear ◽  
Wear Properties ◽  
Weight Percentage ◽  
Casting Technique ◽  
Grey Relational

In this research, investigations were carried out on Al6061 base alloy with the changing weight percentage of silicon carbide (SiC) and boron carbide (B4C) with keeping the amount of talc constant. The main objective of this present study was to improve the wear resistance of aluminum alloy using SiC/B4C/talc ceramic particles using stir-casting technique and how the eco-friendly talc content influencing the solid lubricity during the abrasion process. The experiments were conducted via orthogonal array of L27 using Taguchi’s method. The optimum value along with the coefficient of friction was obtained on the basis of grey relational equations and ANOVA, which helped in analysis of most influential input parameters such as applied load, sliding speed, sliding distance and percentage of reinforcement. Conformation tests were performed for the purpose of validation of the experimental results. The specimens were analyzed using scanning electron microscope (SEM) with EDX for micro structural studies. The SiC, B4C and talc presence in the composite helped to improve the mechanical properties, according to the results. The presence of solid lubricant talc as reinforcement to the aluminum hybrid composite reduced the wear properties and decreased the co-efficient friction. These wear resistance improved aluminum metal matrix composites could be used in automobile, defense and domestic applications where high strength and wear resistance required with lesser specific weight.

scholarly journals Effect of Necklace-Type Distribution of SiC Particles on Dry Sliding Wear Behavior of As-Cast AZ91D/SiCp Composites

Crystals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 296 ◽  
Author(s):  
Chao Sun ◽  
Nannan Lu ◽  
Huan Liu ◽  
Xiaojun Wang ◽  
Xiaoshi Hu ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Interface Bonding ◽  
Type Distribution ◽  
Wear Rates ◽  
Sic Particles ◽  
The Matrix

In this study, the dry sliding wear behaviors of SiC particle reinforced AZ91D matrix composites fabricated by stirring casting method were systematically investigated. The SiC particles in as-cast composites exhibited typical necklace-type distribution, which caused the weak interface bonding between SiC particles and matrix in particle-segregated zones. During dry sliding at higher applied loads, SiC particles were easy to debond from the matrix, which accelerated the wear rates of the composites. While at the lower load of 10 N, the presence of SiC particles improved the wear resistance. Moreover, the necklace-type distribution became more evident with the decrease of particle sizes and the increase of SiC volume fractions. Larger particles had better interface bonding with the matrix, which could delay the transition of wear mechanism from oxidation to delamination. Therefore, composites reinforced by larger SiC particles exhibited higher wear resistance. Similarly, owing to more weak interfaces in the composites with high content of SiC particles, more severe delamination occurred and the wear resistance of the composites was impaired.

Wear Properties of Y-TZP Ceramics Dispersed with Second Phase Particles

2008 ◽  
Vol 368-372 ◽  
pp. 744-747
Author(s):  
Xiao Ping Liang ◽  
Shao Bo Xin ◽  
Xiao Hui Wang ◽  
Zheng Fang Yang
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
Mass Fraction ◽  
Normal Load ◽  
Roller Bearing ◽  
Second Phase ◽  
Wear Properties ◽  
Wear Rates ◽  
Second Phase Particles ◽  
Better Than

The wear properties of ADZ (alumina dispersed in Y-TZP) and MDZ (mullite dispersed in Y-TZP) were investigated by using a ring-on-block tribometer. The results showed that for Y-TZP ceramic, the addition of alumina phase (with 10-20% in mass fraction) leads to an improved wear resistance. With the increase of the normal load, the wear rates of ADZ ceramics increase. Under low and medium normal load (100N and 300N), the wear resistance is controlled by the hardness of ceramics, and under high normal load (500N) the fracture toughness is obviously contributed to the wear resistance of the ceramics. For MDZ ceramic, the wear resistance of 15MDZ (15wt% mullite dispersed in Y-TZP) is better than that of 20 MDZ (20wt% mullite) under the normal load from 100 N to 500 N. The mechanical properties of 15MDZ are worse than that of Y-TZP ceramic, but the wear resistance is enhanced due to the action of “needle roller bearing” of the fractured rod-like mullite particles.

Improving the Wear Resistance of Aluminum Fly Ash Composites by Multipass Friction Stir Processing

2015 ◽  
Vol 642 ◽  
pp. 55-59 ◽  
Author(s):  
Shueiwan Henry Juang ◽  
Liang Jing Fan ◽  
Hsu Shuo Chang
Keyword(s):  
Wear Resistance ◽  
Fly Ash ◽  
Friction Stir Processing ◽  
Sliding Wear ◽  
Normal Load ◽  
Aluminum Matrix ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Wear Rates ◽  
Friction Stir

In this study, the multi-pass friction stir processing (MP-FSP) technique was performed on ADC6 aluminum alloy + 5 wt% fly ash composite (A5FC) castings to increase their surface area. The dry sliding wear behaviors of the ADC6 alloy, A5FCs, and MP-FSPed A5FCs were evaluated. Dry sliding wear tests were performed using a ring-on-washer machine at a constant rotation speed of 100 rpm for 60 min, and the normal load was 10, 20, 30, and 40 N. The results showed that the MP-FSPed A5FCs had the lowest wear rates in the load range from 10 to 40 N, and adhesive wear was the major wear mechanism in these tests. The increased wear resistance was mainly due to grain refinement and elimination of casting defects after subjecting the ash composite to MP-FSP. The microstructure of the MP-FSPed A5FCs reveals that the sizes of the added raw fly ash particles decreased from micro-to nanoscale levels, and the nanoscale fly ash was uniformly dispersed in the aluminum matrix.

scholarly journals Effect of Nanobainite Content on the Dry Sliding Wear Behavior of an Al-Alloyed High Carbon Steel with Nanobainitic Microstructure

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1618 ◽  
Author(s):  
Zhaohuan Song ◽  
Songhao Zhao ◽  
Tao Jiang ◽  
Junjie Sun ◽  
Yingjun Wang ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Carbon Steel ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Normal Load ◽  
High Carbon Steel ◽  
Peak Hardness ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
High Carbon

In this work, a multiphase microstructure consisting of nanobainte, martensite, undissolved spherical carbide, and retained blocky austenite has been prepared in an Al-alloyed high carbon steel. The effect of the amount of nanobainite on the dry sliding wear behavior of the steel is studied using a pin-on-disc tester with loads ranging from 25–75 N. The results show that, there is no significant differences in specific wear rate (SWR) for samples with various amounts of nanobainite when the normal load is 25 N. While, the SWR firstly decreases and then increases with increasing the amount of nanobainite, and the optimum wear resistance is obtained for samples with 60 vol.% nanobainite, when the applied load increases to 50 and 75 N. The improved wear resistance is attributed to the peak hardness increment resulted from the transformation of retained austenite to martensite, work hardening, along with amorphization and nanocrystallization of the worn surface. In addition, the highest toughness of the samples with 60 vol.% nanobainite is also proven to play a positive role in resisting sliding wear. EDS (energy dispersion spectrum) and XRD (X-ray diffraction) examinations reveal that the predominant failure mechanism is oxidative wear.

Tribological Behaviors of Polymer Based Composites under Alkaline Conditions

2012 ◽  
Vol 510 ◽  
pp. 563-568
Author(s):  
Yan Ji Zhu ◽  
Hui Juan Qian ◽  
Gui Ying Wang ◽  
Huai Yuan Wang
Keyword(s):  
Wear Resistance ◽  
Frame Structure ◽  
Alkaline Condition ◽  
Wear Properties ◽  
Friction Coefficients ◽  
Wear Rates ◽  
Transfer Films ◽  
Peek Composite ◽  
Alkaline Conditions ◽  
Ptfe Composites

In this paper, polyetheretherketone (PEEK) and polytetrafluoroethylene (PTFE) based composites reinforced with various amounts of potassium titanate whiskers (PTWs) or short carbon fibers (CF) were designed and fabricated respectively. The friction and wear properties of PEEK and PTFE based composites sliding under rigorous alkaline were comparatively investigated. Also, the morphologies of the worn and counterpart surfaces were studied by scanning electron microscopy (SEM). Because of the stable tunnel crystal structure and frame structure micro-reinforcement capacity, PTWs show outstanding performances in increasing the wear resistance and reducing the friction coefficients of both PEEK and PTFE based composites under alkaline. However, CF leads to the degradation of wear resistance and the increase of friction coefficient of PEEK based composites under alkaline. Furrows and abrasive wear were the main mechanisms for CF/PTFE/PEEK and CF/PTFE composites sliding in alkali. The results show that PTW/PTFE composites exhibit higher wear resistance under lower load, while PTW/PTFE/PEEK composite is more suitable for higher load under alkaline condition. Owing to the primary cooling and boundary lubricating effects of alkali, the wear rates and friction coefficients of PTFE composites and PTW/PTFE/PEEK composites decreased obviously, though the transfer films onto the counterpart steel surface were hindered considerably.

Sign in / Sign up

Export Citation Format

Share Document