IMPACT STRENGTH TEST ON ADDITION OF AGAVE SISALANA FIBER AND E-GLASS FIBER IN ACRYLIC RESIN DENTAL PLATE REPAIR

2021 ◽  
Vol 17 (1) ◽  
pp. 49-55
Author(s):  
Ni Kadek Sugianitri ◽  
◽  
Suhendra Suhendra ◽  
Keyword(s):  
Impact Strength ◽  
Glass Fiber ◽  
Acrylic Resin ◽  
Control Group ◽  
Denture Base ◽  
Denture Plate ◽  
Significant Difference ◽  
The Impact ◽  
Agave Sisalana ◽  
Fiber Addition

Introduction: Acrylic resin is the most common material for the denture base because the acrylic resin has good esthetics, ease of processing, reparability, and inexpensive. A disadvantage of acrylic resin is that it is easy to be cracked. One of the ways to resolve this problem is by adding agave sisalana fiber and E-glass fiber. The purpose of this study was to find out the effect of the addition of agave sisalana fiber and E-glass fiber on the impact strength of an acrylic resin denture plate reparation. Material and Method: The experiment involved twenty-seven plates of heat-cured acrylic with the dimensions of 55x 10 x 10 mm with the 26 x 5 x 4 mm for the cavity to measure, each measurement divided into three groups, with nine samples for each group. The first group was a control group (without fiber), the second group was a group with agave sisalana fiber addition, the third group was a group with e-glass fiber addition. All plates were soaked in distillation water for one day at 37o C. Plates were tested for impact strength using the Charpy method. All data obtained were analyzed with one-way ANOVA followed by LSD (Least Significant Difference) with p<0,05. Result and Discussion: The result showed that the influences of impact strength between without fiber with agave sisalana fiber and E-glass fiber addition on acrylic denture reparation. Acrylic denture reparation in both fibers with concentration 3,3%, agave sisalana fiber has the highest impact strength rather than e-glass fiber. Conclusion: The conclusion of this study is that there is an increase in impact strength with agave sisalana fiber and E-glass fiber addition on acrylic denture reparation and agave sisalana fiber has the highest impact strength.

scholarly journals PENGARUH PENAMBAHAN ZIRKONIUM OKSIDA DAN SERAT POLIPROPILEN TERHADAP KEKUATAN IMPAK DAN TRANSVERSAL BAHAN BASIS GIGI TIRUAN RESIN AKRILIK POLIMERISASI PANAS

2018 ◽  
Vol 12 (2) ◽  
pp. 177-182
Author(s):  
Eddy Dahar ◽  
Raudhatul Husna
Keyword(s):  
Polypropylene Fiber ◽  
Acrylic Resin ◽  
Mean Value ◽  
Zro2 Nanoparticles ◽  
Control Group ◽  
Denture Base ◽  
Transverse Strength ◽  
Significant Difference ◽  
The Mean ◽  
The Impact

Heat polymerized acrylic resin is the most common material used for making denture base because of it’s advantages. However, this material still hasn’t fulfill all the ideal requirements as a denture base. Some disadvantages that need to be fixed are low impact and transverse strength causing an easy base of fracture. Several attempts were made to improve the mechanical properties of heat polymerized acrylic resin materials by adding reinforcing materials. Zirconium oxide is one of chemical group that can be used as a reinforcing material and polypropylene fiber which is including in fiber reinforcing groups. This study aims to determine whether there is a difference in the effect of the addition of 5% ZrO2 nanoparticles and 2% chopped polypropylene fibers 6 mm in length on the impact and transverse strength of heat polymerized acrylic resin denture base material. The design of this study is a laboratory experimental and the number of samples in this study are 60 samples. The result of this study shows the mean value of the impact and transverse strength of heat polymerized acrylic resin with ZrO2 nanoparticles reinforced is greater than the control group and heat polymerized acrylic resin group with polypropylene fiber reinforced with significant difference, and the mean value of impact and transverse strength of heat polymerized acrylic resin with polypropylene fibers reinforced is greater than the control group with significant difference.

scholarly journals Enhancing the impact strength of acrylic resin base plate by adding non-dental E-glass fiber

2021 ◽  
Vol 6 (2) ◽  
pp. 106
Author(s):  
Mara Gustina ◽  
Widjijono Widjijono ◽  
Endang Wahyuningtyas
Keyword(s):  
Impact Strength ◽  
Glass Fiber ◽  
Fiber Orientation ◽  
Base Plate ◽  
Acrylic Resin ◽  
Impact Testing ◽  
Control Group ◽  
Anova Test ◽  
The Impact ◽  
One Way Anova

Non-dental glass fiber is one of the materials that can be used to increase the impact strength of a acrylic resin base plate, containing a similar composition to that of dental e-glass fiber. Orientation and positions of fiber affect the reinforcement effectiveness. This research aimed to examine the effect of the orientation of non-dental glass fiber in the compression position on the impact strength of an acrylic resin base plate. The research was conducted on 16 acrylic resin plates with fiber (65 mm x 10 mm x 2.5 mm) addition. The samples were divided into 4 groups (combination of different woven orientation unidirectional, bidirectional woven in the compression position, and control). The material used in this study was heat-cured acrylic resin QC-20 brand, non-dental glass fiber (without any brand). Impact strength was tested using an impact testing machine. The data obtained were analyzed using one-way ANOVA test and LSD (p<0.05). In this research the impact strength of the base plate with the addition of fiber increased 8.54 ± 2.21; 13.21 ± 2.34; 16.81 ± 2.80 kJ/m2 compared to that of the control group, i.e. 4.98 ± 1.05 kJ/m2. One-way ANOVA test showed a significant effect (p<0.05) of the fiber orientation variations on the compression position. This research concluded that the addition of nondental e-glass fiber (composed of SiO252.56-56.88%), diameter 17.12–20.03 µm) in the compression zone increases theimpact strength of acrylic resin base plate. Fibers with unidirectional orientationprovides the highest increase in the impact strength of acrylic resin base plate.

scholarly journals TiO2-Nanofillers Effects on Some Properties of Highly- Impact Resin Using Different Processing Techniques

2018 ◽  
Vol 12 (1) ◽  
pp. 202-212 ◽  
Author(s):  
Hawraa Khalid Aziz
Keyword(s):  
Thermal Conductivity ◽  
Impact Strength ◽  
Color Stability ◽  
Acrylic Resin ◽  
Water Bath ◽  
Control Group ◽  
Significance Level ◽  
Significant Difference ◽  
And Control ◽  
The Impact

Background: The criteria of conventional curing of polymethyl methacrylate do not match the standard properties of the denture base materials. Objectives: This research was conducted to investigate the addition of TiO2 nano practical on impact strength, thermal conductivity and color stability of acrylic resin cured by microwave in comparison to the conventional cured of heat-polymerized acrylic resin. Materials and Methods: 120 specimens made of high impact acrylic resin were divided into two main groups according to the type of curing (water bath, microwave), then each group was subdivided into two groups according to the addition of 3% TiO2 nano-fillers and control group (without the addition of TiO2 0%). Each group was subdivided according to the type of test into 3 groups with 10 specimens for each group. Data were statistically analyzed using Student t-test to detect the significant differences between tested and control groups at significance level (P<0.05). Results: According to curing type methods, the results showed that there was a significant decrease in impact strength of microwaved cured resin, but there was no significant difference in the thermal conductivity and color stability of resin. In addition, by using nanofiller, there was a significant increase in the impact strength and color stability with the addition of 3% TiO2 nanofillers, but no significant difference was found in the thermal conductivity of the acrylic resin. Conclusion: The microwave curing of acrylic resin had no change in the color stability and thermal conductivity in comparison to the water bath, but the impact strength was decreased. The addition of 3% TiO2 improved the impact and the color stability, but the thermal conductivity did not change.

scholarly journals The effect of nanoparticles TiO2 on the flexural strength of acrylic resin denture plate

2018 ◽  
Vol 30 (1) ◽  
pp. 35 ◽  
Author(s):  
Edwin Tandra ◽  
Endang Wahyuningtyas ◽  
Erwan Sugiatno
Keyword(s):  
Flexural Strength ◽  
Testing Machine ◽  
Base Material ◽  
Acrylic Resin ◽  
Control Group ◽  
Denture Base ◽  
Denture Plate ◽  
Significant Difference ◽  
Strength Difference ◽  
The One

Introduction: Acrylic resin is still the most commonly used denture base material due to its ideal properties. However, acrylic resin denture fractures are still considered a major unsolved problem thus the addition of nanoparticles as filler was performed to increase its mechanical properties. The purpose of this study was to discovered the effect of nanoparticles TiO2 on the flexural strength of acrylic resin denture plate. Method: This study used 27 heat-cured acrylic resin specimens sized 65 x 10 x 2.5 mm. The samples were divided into three concentration groups (n = 9), the control group; 1% of nanoparticles TiO2; and 3% of nanoparticles TiO2. The flexural strength was tested using the Universal Testing Machine. All data were analysed using the one-way ANOVA test with 95% confidence level then continued with the Least Significant Difference (LSD) test. Results: There were significant flexural strength differences in different concentration of nanoparticles TiO2. The highest flexural strength value was found in the 1% of nanoparticles TiO2 group (106.99 ± 6.09 MPa), whilst the lowest flexural strength value was found in the 3% of nanoparticles TiO2 group (91.64 ± 5.38 MPa). Significant flexural strength difference was found between the control group and the 1% of nanoparticles TiO2 group, and also between the 1% of nanoparticles TiO2 group with the 3% of nanoparticles TiO2 group (p < 0.05). Conclusion: From this study can be concluded that concentration of 1% of nanoparticles TiO2 was able to increase the flexural strength of acrylic resin denture plate.

ENHANCEMENT OF DENTURE-BASED MATERIAL PMMA BY INCORPORATION OF SILANIZED HALLOYSITE NANOTUBES

2021 ◽  
Vol 74 (9) ◽  
pp. 2293-2296
Author(s):  
Rafah Habib Abdul Amir
Keyword(s):  
Impact Strength ◽  
Base Material ◽  
Hardness Test ◽  
Acrylic Resin ◽  
Halloysite Nanotubes ◽  
Control Group ◽  
Transverse Strength ◽  
Comparison Results ◽  
Significant Difference ◽  
The Impact

The aim: This study evaluates the effect of adding silanized halloysite nanotubes to the polymethylmethacrylate (PMMA) resin on its hardness, impact strength, transverse strength. Materials and methods: Three groups of acrylic resin were prepared, one group without HNTs, was used as a control group (A). The other two groups contained 0.3% (B), 0.6% wt of silanized halloysite nanotubes (C). For each one, hardness, impact strength and transverse strength were measured. One-way ANOVA and Tukey’s test were used for comparison. Results: Regarding to the impact test, there was no significant difference between 0.3% concentration and the pure (control) group while 0.6% concentration had significant decrease compared to the pure group and so between the 0.3% group 0.6% group. For the hardness test, the 0.3% group had no significant difference with the pure group and a significant difference between group 0.6% group and the pure group while there was a no significant decrease between the 0.3% and 0.6% group with the higher hardness mean in the 0.3% compared to 0.6% group. For the transverse strength, both 0.3% wt concentration and 0.6% concentration showed significant difference compared to the pure group and also between each other with the lowest impact strength in 0.6% group followed by 0.3% group with the highest transverse strength in the pure group. Conclusions: The silanation of halloysite nanotubes reduces the mechanical properties of the heat-cured acrylic denture base material. The more concentration of silanazed halloysite nanotubes is added, the more weakening occurs in the acrylic material relating to the hardness, transverse strength and impact strength.

IMMERSION OF HEAT POLYMERIZED ACRYLIC RESIN DENTAL BASE IN ARAK BALI AGAINST SURFACE ROUGHNESS

2021 ◽  
Vol 17 (1) ◽  
pp. 22-26
Author(s):  
Kadek Ayu Wirayuni ◽  
◽  
I Made Hendri Dwi Saputra ◽  
Keyword(s):  
Surface Roughness ◽  
Acrylic Resin ◽  
Control Group ◽  
Surface Strength ◽  
Denture Base ◽  
A Value ◽  
Removable Denture ◽  
Significant Difference ◽  
Post Test ◽  
Oral Tissue

Introduction: The denture base is the part of the removable denture that is supported by good adaptation to the underlying oral tissue. Most of the denture bases are made of acrylic or polymethyl methacrylate resin, better known as PMMA. However, the acrylic resin also has disadvantages such as easily broken and absorbs liquids both water and chemicals. The chemical absorption like alcohol, ethanol, and some drinks that contain acidic materials will chemically be induced with acrylic resin and settle in the pores of the acrylic resin. The chemical damage or defect creates roughness on the surface of the acrylic resin which can cause cracking or crazing and a decrease in surface strength and hardness. Materials and Methods: The method used in this research was a laboratory experimental design with a post-test-only control group using 12 samples consisting of 2 different types of samples by measuring the surface roughness of the acrylic resin after immersing the sample with a predetermined time. Results and Discussions: One-way ANOVA test results showed a significant difference in surface roughness after the samples immersion with a value of p = 0.006 (p <0.05). Conclusions: Based on this research, can be concluded that there is an increase in the surface roughness of the heated polymerized acrylic resin for 3 hours and 4 hours of immersion. The longer the heated polymerized acrylic resin is soaked in arak hence the level of surface roughness increases.

Evaluation of Tissue Reaction to Some Denture-base Materials: An Animal Study

2008 ◽  
Vol 9 (4) ◽  
pp. 67-74 ◽  
Author(s):  
Behnaz Ebadian ◽  
Mohammad Razavi ◽  
Solmaz Soleimanpour ◽  
Ramin Mosharraf
Keyword(s):  
Animal Study ◽  
Weight Ratio ◽  
Acrylic Resin ◽  
Tissue Reaction ◽  
Control Group ◽  
Denture Base ◽  
Base Materials ◽  
Heat Cure ◽  
Two Samples ◽  
Significant Difference

Abstract Aim Controversy continues regarding the biocompatibility of denture base materials. One method to evaluate the biocompatibility of materials is in an animal study. Using dogs as subjects, the purpose of this study was to evaluate the vestibular tissue reaction to cobalt chromium (Co-Cr), heat cure acrylic resin, and acrylic resin mixed with aluminum oxide (Al2O3) compared with a control group using the histopathologic method. Methods and Materials Twelve disk shape samples (2 mm × 8 mm) in four groups of Co-Cr, acrylic resin, acrylic resin mixed with a 20% weight ratio of Al2O3, and a control group (Teflon) were fabricated. In one stage surgery two samples of each material (8 samples) was implanted in the buccal vestibule of each dog (n=6), subcutaneously. At 45 and 90-day intervals, half of the samples were excised along with peripheral tissue to assess the presence of inflammation by grading on a scale from 0 to 3 and the presence of a fibrotic capsule using histological observations. Data were analyzed using the Kruskal-Wallis, Mann-Whitney, and Tau b Kendal tests. Results Tissue reaction between Co-Cr and the control group was significant (P=0.02), but it was not significant between other groups. There was no significant difference between the 45 and 90-day postinsertion samples. The formation of fibrotic capsule groups was significant (P=0.01). It was significant between the Co-Cr and acrylic resin groups (P=0.01) and the acrylic resin and control groups (P=0.01). Conclusion The Co-Cr group was more toxic than the other groups. The inflammation increased during time. The inflammation in two acrylic groups was greater than the control and less than the Co-Cr group. The formation of fibrotic capsule, except in the acrylic resin with Al2O3 group, increased over time. Clinical Significance Co-Cr alloys are toxic and can produce damage to living tissue. Heat cure acrylic resin materials have less toxicity, and their use is safer than Co-Cr alloys. Citation Ebadian B, Razavi M, Soleimanpour S, Mosharraf R. Evaluation of Tissue Reaction to Some Denture-base Materials: An Animal Study. J Contemp Dent Pract 2008 May; (9)4:067-074.

scholarly journals The effect of polyamide microparticles addition on some mechanical prop-erties of light-cured acrylic resin

2019 ◽  
Vol 10 (2) ◽  
pp. 1464-1469
Author(s):  
Adnan R. Al Assal ◽  
Abdalbaset A Fatalla ◽  
Mohammed Moudhaffar ◽  
Ghasak H Jani
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Base Material ◽  
Acrylic Resin ◽  
Strength Test ◽  
Control Group ◽  
Denture Base ◽  
Mean Values ◽  
Transverse Strength ◽  
Transverse Tensile

The general upgrading of polymer denture base material and research continuously looking for ideal restorative dental material with better properties, adequate esthetic properties, less expensive and easier to handle material to develop photo polymerization dental materials. This study was conducted to evaluate the effect of addition polyamide on mechanical microparticle properties light cure denture base material. One hindered sixty specimens from light-cured acrylic resin (Aurora). The divided mainly into four groups according to test used (Transverse strength test, impact strength test, hardness test and tensile strength test) with 40 specimens for each group. The results show an increase in Transverse strength, impact strength, hardness and tensile strength in all experimental group when compared to control group the highest mean values for all tests included in the study appeared in group B 1% polyamide. The addition of polyamide microparticle improves transverse, tensile, impact strength and hardness properties of denture base material.

scholarly journals ADDITION OF RICE HUSK NANOCELLULOSE TO THE IMPACT STRENGTH OF RESIN BASE HEAT CURED

2021 ◽  
Vol 4 (3) ◽  
pp. 119
Author(s):  
Muhammad Aditya Ramadhan Hasran ◽  
Dian Noviyanti Agus Imam ◽  
Bambang Sunendar
Keyword(s):  
Impact Strength ◽  
Mechanical Strength ◽  
Rice Husk ◽  
Acrylic Resin ◽  
Control Group ◽  
P Value ◽  
Test Results ◽  
Nano Cellulose ◽  
Reinforcing Material ◽  
The Impact

Background: One of the materials for denture bases is heat-cured acrylic resin (PMMA). This material still lacks impact strength as a mechanical strength property. The addition of reinforcing material is known to increase the mechanical strength of PMMA. One of the reinforcing materials added to PMMA is nano cellulose from rice husks, one of the wastes from agricultural products. Purpose: This study aims to determine rice husk nano cellulose's addition to the PMMA denture base's impact strength. Method:  The research sample consisted of six groups, each group consisting of 8 samples selected by simple random. The PI, P2, P3, P4, P5, and K groups were PMMA with 1%, 2%, 3%, 4%, 5% nano cellulose, and without nano cellulose. Result: Mean impact strength test results were 41.50 x 10-3 ± 3.891 J / mm2 for P1, 44.13 x 10-3 ± 3,980 J / mm2 for P2, 45.63 x 10-3 ± 4,438 J / mm2 for P3, 46.87 x 10-3 ± 4,824 J / mm2 for P4, 49.12 x 10-3 ± 4.016 J / mm2 for P5 and 36.25 x 10-3 ± 1.982 J / mm2 for K. One way Anova test results with p-value of 0.000 indicates differences in the six groups (p<0.05). Conclusion: This study concludes that the impact strength value of PMMA with the addition of rice husk nano cellulose has increased compared to the control group without the addition of rice husk nano cellulose.

scholarly journals Influence of Concentrations of Methacrylate and Acrylate Monomers on the Properties of Fiber Reinforced Polymethyl Methacrylate Denture Base Materials

2018 ◽  
Vol 26 (2) ◽  
pp. 329-350 ◽  
Author(s):  
Faik Tugut ◽  
Mehmet Turgut ◽  
Dursun Saraydin
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Testing Machine ◽  
Weight Ratio ◽  
Acrylic Resin ◽  
Bending Test ◽  
Control Group ◽  
Test Machine ◽  
Fiber Reinforced ◽  
Significant Difference

Abstract The study aimed to evaluate the effects of adding different concentrations of 2 hydroxyethyl methacrylate (HEMA), 2-hydroxyethyl acrylate (HEA), ethyl methacrylate (EA) and isobutyl methacrylate (IBMA) monomers on the structural, thermal and mechanical properties of a fiber reinforced heat-polymerized acrylic resin. For each test, 126 acrylic resin specimens were fabricated and divided into 6 groups with 7 specimens each. One group was the control group, the other one is a fiber reinforced group and others were the test groups, which were formed according to the different concentrations of monomers. 6 mm length, and the weight ratio of 3% short glass fibers are added to acrylic powder polymerized by heating. The 2%, 5%, 10%, at 20 % ratios of different comonomers added to a monomer of MMA are composed of copolymer structures. Flexural strength was assessed with a three-point bending test using a universal testing machine. Impact strength testing was conducted using an impact test machine by the Charpy method. The analysis of the connection between acrylic resin and fiber by SEM and structural changes in the acrylic resin was investigated by FTIR spectroscopy. Data analyses using analysis of Kruskal-Wallis and Mann-Whitney U tests (α=0.05) significant difference tests showed that adding 2%, 5% HEMA and IBMA monomers significantly increased the flexural and impact strength compared to the control, only fiber and others group (P< 0.05). It is observed that the process of adding low concentration of HEMA and IBMA monomers improved certain mechanical properties of fiber reinforced with polymethylmethacrylate.

Sign in / Sign up

Export Citation Format

Share Document