scholarly journals Improving Oil Recovery Efficiency in Niger Delta Reservoirs Using Corn Starch as a Local Polymer

2021 ◽  
Vol 04 (11) ◽  
Author(s):  
Imad Biboye Eseimokumoh ◽  
Keyword(s):  
Oil Recovery ◽  
Niger Delta ◽  
Adsorption Mechanism ◽  
Corn Starch ◽  
Molecular Size ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Residual Oil ◽  
Adsorption Effect ◽  
Recovery Method

Polymer flooding is a chemical enhanced oil recovery method that improves the recovery of oil by controlling the mobility of water to oil phase. It uses polymer solutions to increase the viscosity of the displacing water thereby decreasing water/oil mobility ratio (Speight, 2013). The volumetric and displacement sweep efficiencies are positively affected by polymer flooding. The viscosity of the aqueous phase is increased due to the molecular size and structure of the polymer used. The main objective of this research was to study the ability of cornstarch (local polymer) to recover additional oil after conventional water flooding. The objective was successfully achieved by injecting four different unconsolidated samples (sand pack) with cornstarch solution at varying concentration of 500ppm, 1000ppm, 3000ppm, and 9000ppm. From the results of the experiment conducted, it was deduced that Cornstarch has the ability to recover an additional volume of oil about half the volume of oil recovered during conventional water flooding (i.e. if 50% of oil initially in place was recovered during water flooding, cornstarch can recover an additional 25% of the residual oil after water flooding). Also, higher concentrations of cornstarch reduce the recovery factor due to polymer adsorption on the rock surfaces which alters the rock wettability. To reduce the adsorption effect of Cornstarch, it is recommended that the concentration of Cornstarch be measured after the flooding experiments for a better understanding of the adsorption mechanism of cornstarch.

scholarly journals SURFACTANT-POLYMER FLOODING PERFORMANCE IN HETEROGENEOUS TWO-LAYERED POROUS MEDIA

2011 ◽  
Vol 12 (1) ◽  
pp. 31-38 ◽  
Author(s):  
Muhammad Taufiq Fathaddin ◽  
Asri Nugrahanti ◽  
Putri Nurizatulshira Buang ◽  
Khaled Abdalla Elraies
Keyword(s):  
Porous Media ◽  
Oil Recovery ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Residual Oil ◽  
Oil Saturation ◽  
Reservoir Heterogeneity ◽  
Residual Oil Saturation ◽  
Layered Porous Media ◽  
Multiple Porosity

In this paper, simulation study was conducted to investigate the effect of spatial heterogeneity of multiple porosity fields on oil recovery, residual oil and microemulsion saturation. The generated porosity fields were applied into UTCHEM for simulating surfactant-polymer flooding in heterogeneous two-layered porous media. From the analysis, surfactant-polymer flooding was more sensitive than water flooding to the spatial distribution of multiple porosity fields. Residual oil saturation in upper and lower layers after water and polymer flooding was about the same with the reservoir heterogeneity. On the other hand, residual oil saturation in the two layers after surfactant-polymer flooding became more unequal as surfactant concentration increased. Surfactant-polymer flooding had higher oil recovery than water and polymer flooding within the range studied. The variation of oil recovery due to the reservoir heterogeneity was under 9.2%.

scholarly journals Differences of microscopic seepage mechanisms of water flooding and polymer flooding and prediction models of final oil recovery for conglomerate reservoir

2019 ◽  
Vol 74 ◽  
pp. 13
Author(s):  
Fengqi Tan ◽  
Changfu Xu ◽  
Yuliang Zhang ◽  
Gang Luo ◽  
Yukun Chen ◽  
...  
Keyword(s):  
Pore Structure ◽  
Polymer Solution ◽  
Oil Recovery ◽  
Particle Surface ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Residual Oil ◽  
Displacement Efficiency ◽  
Oil Saturation ◽  
Oil Displacement Efficiency

The special sedimentary environments of conglomerate reservoir lead to pore structure characteristics of complex modal, and the reservoir seepage system is mainly in the “sparse reticular-non reticular” flow pattern. As a result, the study on microscopic seepage mechanism of water flooding and polymer flooding and their differences becomes the complex part and key to enhance oil recovery. In this paper, the actual core samples from conglomerate reservoir in Karamay oilfield are selected as research objects to explore microscopic seepage mechanisms of water flooding and polymer flooding for hydrophilic rock as well as lipophilic rock by applying the Computed Tomography (CT) scanning technology. After that, the final oil recovery models of conglomerate reservoir are established in two displacement methods based on the influence analysis of oil displacement efficiency. Experimental results show that the seepage mechanisms of water flooding and polymer flooding for hydrophilic rock are all mainly “crawling” displacement along the rock surface while the weak lipophilic rocks are all mainly “inrushing” displacement along pore central. Due to the different seepage mechanisms among the water flooding and the polymer flooding, the residual oil remains in hydrophilic rock after water flooding process is mainly distributed in fine throats and pore interchange. These residual oil are cut into small droplets under the influence of polymer solution with stronger shearing drag effect. Then, those small droplets pass well through narrow throats and move forward along with the polymer solution flow, which makes enhancing oil recovery to be possible. The residual oil in weak lipophilic rock after water flooding mainly distributed on the rock particle surface and formed oil film and fine pore-throat. The polymer solution with stronger shear stress makes these oil films to carry away from particle surface in two ways such as bridge connection and forming oil silk. Because of the essential attributes differences between polymer solution and injection water solution, the impact of Complex Modal Pore Structure (CMPS) on the polymer solution displacement and seepage is much smaller than on water flooding solution. Therefore, for the two types of conglomerate rocks with different wettability, the pore structure is the main controlling factor of water flooding efficiency, while reservoir properties oil saturation, and other factors have smaller influence on flooding efficiency although the polymer flooding efficiency has a good correlation with remaining oil saturation after water flooding. Based on the analysis on oil displacement efficiency factors, the parameters of water flooding index and remaining oil saturation after water flooding are used to establish respectively calculation models of oil recovery in water flooding stage and polymer flooding stage for conglomerate reservoir. These models are able to calculate the oil recovery values of this area controlled by single well control, and further to determine the oil recovery of whole reservoir in different displacement stages by leveraging interpolation simulation methods, thereby providing more accurate geological parameters for the fine design of displacement oil program.

scholarly journals A Pore-Scale Investigation of Residual Oil Distributions and Enhanced Oil Recovery Methods

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3732 ◽  
Author(s):  
Yaohao Guo ◽  
Lei Zhang ◽  
Guangpu Zhu ◽  
Jun Yao ◽  
Hai Sun ◽  
...  
Keyword(s):  
Porous Media ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Scale Model ◽  
Pore Scale ◽  
Residual Oil ◽  
Sweep Efficiency ◽  
Significant Difference

Water flooding is an economic method commonly used in secondary recovery, but a large quantity of crude oil is still trapped in reservoirs after water flooding. A deep understanding of the distribution of residual oil is essential for the subsequent development of water flooding. In this study, a pore-scale model is developed to study the formation process and distribution characteristics of residual oil. The Navier–Stokes equation coupled with a phase field method is employed to describe the flooding process and track the interface of fluids. The results show a significant difference in residual oil distribution at different wetting conditions. The difference is also reflected in the oil recovery and water cut curves. Much more oil is displaced in water-wet porous media than oil-wet porous media after water breakthrough. Furthermore, enhanced oil recovery (EOR) mechanisms of both surfactant and polymer flooding are studied, and the effect of operation times for different EOR methods are analyzed. The surfactant flooding not only improves oil displacement efficiency, but also increases microscale sweep efficiency by reducing the entry pressure of micropores. Polymer weakens the effect of capillary force by increasing the viscous force, which leads to an improvement in sweep efficiency. The injection time of the surfactant has an important impact on the field development due to the formation of predominant pathway, but the EOR effect of polymer flooding does not have a similar correlation with the operation times. Results from this study can provide theoretical guidance for the appropriate design of EOR methods such as the application of surfactant and polymer flooding.

Experimental Study of Polymer Flooding in Fractured Systems Using Five-Spot Glass Micromodel: The Role of Fracture Geometrical Properties

2012 ◽  
Vol 30 (5) ◽  
pp. 689-705 ◽  
Author(s):  
Behbood Abedi ◽  
Mohammad Hossein Ghazanfari ◽  
Riyaz Kharrat
Keyword(s):  
Oil Recovery ◽  
Polymer Flooding ◽  
Recovery Factor ◽  
Reservoir Rock ◽  
Water Flooding ◽  
Recovery Method ◽  
Geometrical Properties ◽  
Fracture Orientation ◽  
Glass Micromodel

Water flooding is being widely used in the petroleum industry and has been considered as a simple inexpensive secondary recovery method. But in fractured formations, existence of fracture system in reservoir rock induces an adverse effect on oil recovery by water flooding. Polymer flooding has been successfully applied as an alternative enhanced oil recovery method in fractured formations. But, the role of fracture geometrical properties on macroscopic efficiency of polymer flooding is not yet well-understood, especially in fractured five-spot systems. In this work five-spot glass micromodel, because of micro-visibility, ease of multiple experimentations and also presence of the unexplored issues, was used to experimentally investigate the influence of fracture geometrical characteristics such as fracture orientation, fracture spacing, fracture overlap and etc on the macroscopic efficiency of polymer flooding. The tests were performed on the fractured models which are initially saturated with the crude oil at fixed flow rate conditions and in a horizontally mounting. The results revealed that the macroscopic efficiency of polymer flooding depends on fracture geometrical properties. Fracture orientation showed more imposing effect than other fracture geometrical properties, and fracture with 45 degree inclination to the mean flow direction, gives greatest oil recovery factor. Large spacing fractures give more recovery than small spacing ones and in case of overlapping, fractures with less overlapping help polymer to better propagate which could be related to their greater effective fracture length. This pre-called effect could be responsible to show how continuity and width to length ratio of fractures affect recovery factor, less fracture discontinuity as well as more length to width ratio of fracture give more swept zone. Also, increasing number of fractures decreases oil recovery factor. The results of this work can be helpful to better understanding the role of fracture geometrical properties on macroscopic efficiency of polymer flooding in five-spot fractured systems.

scholarly journals The Key Parameter Effect Analysis Of Polymer Flooding On Oil Recovery Using Reservoir Simulation

2019 ◽  
Vol 4 (1) ◽  
pp. 49
Author(s):  
Tomi Erfando ◽  
Novia Rita ◽  
Romal Ramadhan
Keyword(s):  
Oil Recovery ◽  
Reservoir Simulation ◽  
Polymer Concentration ◽  
Polymer Flooding ◽  
Recovery Factor ◽  
Water Flooding ◽  
Base Case ◽  
Driving Mechanism ◽  
Geological Condition ◽  
Recovery Method

As time goes by, there will be decreasing of production rates of a field along with decreasing pressure. This led to the necessity for further efforts to increase oil production. Therefore, pressure support is required to improve the recovery factor. Supportable pressure that can be used can be either water flooding and polymer flooding. This study aims to compare recovery factor to scenarios carried out, such as polymer flooding with different concentrations modeled in the same reservoir model to see the most favorable scenario. The method used in this research is reservoir simulation method with Computer Modeling Group (CMG) STARS simulator. The study was carried out by observing at the pressure, injection rate, and polymer concentration on increasing field recovery factor. This study used cartesian grid with the assumption of homogeneous reservoir, there are no faults or other geological condition in the reservoir, and driving mechanism is only solution gas drive. This reservoir, oil type is light oil with API gravity 40.3˚API and layer of conglomerate rock. The simulation result performed with various scenarios provides a good result. Where the conditions case base case field recovery factor of 6.7%, and after water flooding produced 25.5% of oil, whereas with tertiary recovery method is polymer flooding was carried out with four concentrations of 640 ppm, 1,500 ppm, 3,000 ppm, and 4,000 ppm obtained optimum values at 4,000 ppm polymer concentration with recovery factor 28.9%, SOR reduction final value 0,5255, polymer adsorption of 818,700 ppm, reservoir final pressure 1,707 psi, and an increase in water viscosity to 0.94 cP.

Experimental Investigation of Microscopic/Macroscopic Efficiency of Polymer Flooding in Fractured Heavy Oil Five-Spot Systems

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Mohammad Hossein Sedaghat ◽  
Mohammad Hossein Ghazanfari ◽  
Mohammad Parvazdavani ◽  
Saeid Morshedi
Keyword(s):  
Experimental Investigation ◽  
Oil Recovery ◽  
Polymer Concentration ◽  
Synthetic Polymers ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Recovery Efficiency ◽  
Recovery Method ◽  
Geometrical Properties ◽  
Glass Type

This paper concerns on experimental investigation of biopolymer/polymer flooding in fractured five-spot systems. In this study, a series of polymer injection processes were performed on five-spot glass type micromodels saturated with heavy crude oil. Seven fractured glass type micromodels were used to illustrate the effects of polymer type/concentration on oil recovery efficiency in presence of fractures with different geometrical properties (i.e., fractures orientation, length and number of fractures). Four synthetic polymers as well as a biopolymer at different levels of concentration were tested. Also a micromodel constituted from dead-end pores with various geometrical properties was designed to investigate microscopic displacement mechanisms during polymer/water flooding. The results showed that polymer flooding is more efficient by using hydrolyzed synthetic polymers with high molecular weight as well as locating injection well in a proper position respect to the fracture geometrical properties. In addition, by monitoring of microscopic efficiency, pulling, stripping, and oil thread flow mechanisms were detected and discussed. The results showed that flow rate, fluid type, polymer concentration, and geometrical properties of pores influence the efficiency of mentioned mechanisms. Furthermore, it was detected that polymer's velocity profile play a significant role on oil recovery efficiency by influencing both macroscopic and microscopic mechanisms. This study demonstrates different physical and chemical conditions that affect the efficiency of this enhanced oil recovery method.

scholarly journals Experimental Study on Medium Viscosity Oil Displacement Using Viscoelastic Polymer

Geofluids ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Huiying Zhong ◽  
Qiuyuan Zang ◽  
Hongjun Yin ◽  
Huifen Xia
Keyword(s):  
Oil Recovery ◽  
Polymer Flooding ◽  
Water Soluble ◽  
Water Flooding ◽  
Bohai Bay ◽  
Residual Oil ◽  
Displacement Efficiency ◽  
Sweep Efficiency ◽  
Oil Displacement ◽  
Medium Viscosity

With the growing demand for oil energy and a decrease in the recoverable reserves of conventional oil, the development of viscous oil, bitumen, and shale oil is playing an important role in the oil industry. Bohai Bay in China is an offshore oilfield that was developed through polymer flooding process. This study investigated the pore-scale displacement of medium viscosity oil by hydrophobically associating water-soluble polymers and purely viscous glycerin solutions. The role and contribution of elasticity on medium oil recovery were revealed and determined. Comparing the residual oil distribution after polymer flooding with that after glycerin flooding at a dead end, the results showed that the residual oil interface exhibited an asymmetrical “U” shape owing to the elasticity behavior of the polymer. This phenomenon revealed the key of elasticity enhancing oil recovery. Comparing the results of polymer flooding with that of glycerin flooding at different water flooding sweep efficiency levels, it was shown that the ratio of elastic contribution on the oil displacement efficiency increased as the water flooding sweep efficiency decreased. Additionally, the experiments on polymers, glycerin solutions, and brines displacement medium viscosity oil based on a constant pressure gradient at the core scale were carried out. The results indicated that the elasticity of the polymer can further reduce the saturation of medium viscosity oil with the same number of capillaries. In this study, the elasticity effect on the medium viscosity oil interface and the elasticity contribution on the medium viscosity oil were specified and clarified. The results of this study are promising with regard to the design and optimum polymers applied in an oilfield and to an improvement in the recovery of medium viscosity oil.

Evaluating Efficiency of Surfactant-Polymer Flooding with Single Well Chemical Tracer Tests at Kholmogorskoye Field

2021 ◽  
Author(s):  
Mikhail Bondar ◽  
Andrey Osipov ◽  
Andrey Groman ◽  
Igor Koltsov ◽  
Georgy Shcherbakov ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Promising Result ◽  
Tracer Tests ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Residual Oil ◽  
Core Flooding ◽  
Oil Saturation ◽  
Chemical Eor ◽  
Single Well

Abstract EOR technologies in general and surfactant-polymer flooding (SP) in particular is considered as a tertiary method for redevelopment of mature oil fields in Western Siberia, with potential to increase oil recovery to 60-70% OOIP. The selection of effective surfactant blend and a polymer for SP flooding a complex and multi-stage process. The selected SP compositions were tested at Kholmogorskoye oilfield in September-December 2020. Two single well tests with partitioning chemical tracers (SWCTT) and the injectivity test were performed. The surfactant and the polymer for chemical EOR were selecting during laboratory studies. Thermal stability, phase behavior, interfacial tension and rheology of SP formulation were investigated, then a prospective chemical design was developed. Filtration experiments were carried out for optimization of slugs and concentrations. Then SWCTT was used to evaluated residual oil saturation after water flooding and after implementation of chemical EOR in the near wellbore areas. The difference between the obtained values is a measure of the efficiency of surfactant-polymer flooding. Pandemic restriction shifted SWCTT to the period when temperature dropped below zero and suitable for winter conditions equipment was required. Two SWCTT were conducted with same surfactant, but different design of slugs in order to prove technical and economic models of SP-flooding. Long-term polymer injectivity was accessed at the third well. Oil saturation of sandstone reservoir after the injection of a surfactant-polymer solution was reduced about 10% points which is around one third of the residual oil after water flooding. Results were compared with other available data such as well logging, lab core flooding experiments, and hydrodynamic simulation. Modeling of SWCTT is ongoing, current interpretation confirms the increase the oil recovery factor after SP-flooding up to 20-25%, which is a promising result. Temperature model of the bottom hole zone was created and verified. The model predicts that temperature of those zones essentially below that average in the reservoir, which is important for interpretation of tracer test and surfactant efficiency. The tested surfactant showed an acceptable efficiency at under-optimum conditions, which is favorable for application of the SP formulation for neighboring field and layers with different reservoir temperatures, but similar water composition. In general, the results of the conducted field tests correlate with the results of the core experiments for the selected surfactant

scholarly journals Experimental investigation of the displacement flow mechanism and oil recovery in primary polymer flood operations

2021 ◽  
Vol 3 (5) ◽  
Author(s):  
Ruissein Mahon ◽  
Gbenga Oluyemi ◽  
Babs Oyeneyin ◽  
Yakubu Balogun
Keyword(s):  
Relative Permeability ◽  
Oil Recovery ◽  
Polymer Flooding ◽  
Mobility Control ◽  
List Type ◽  
Motor Oil ◽  
Flow Mechanism ◽  
Fractional Flow ◽  
Recovery Method ◽  
Polymer Flood

Abstract Polymer flooding is a mature chemical enhanced oil recovery method employed in oilfields at pilot testing and field scales. Although results from these applications empirically demonstrate the higher displacement efficiency of polymer flooding over waterflooding operations, the fact remains that not all the oil will be recovered. Thus, continued research attention is needed to further understand the displacement flow mechanism of the immiscible process and the rock–fluid interaction propagated by the multiphase flow during polymer flooding operations. In this study, displacement sequence experiments were conducted to investigate the viscosifying effect of polymer solutions on oil recovery in sandpack systems. The history matching technique was employed to estimate relative permeability, fractional flow and saturation profile through the implementation of a Corey-type function. Experimental results showed that in the case of the motor oil being the displaced fluid, the XG 2500 ppm polymer achieved a 47.0% increase in oil recovery compared with the waterflood case, while the XG 1000 ppm polymer achieved a 38.6% increase in oil recovery compared with the waterflood case. Testing with the motor oil being the displaced fluid, the viscosity ratio was 136 for the waterflood case, 18 for the polymer flood case with XG 1000 ppm polymer and 9 for the polymer flood case with XG 2500 ppm polymer. Findings also revealed that for the waterflood cases, the porous media exhibited oil-wet characteristics, while the polymer flood cases demonstrated water-wet characteristics. This paper provides theoretical support for the application of polymer to improve oil recovery by providing insights into the mechanism behind oil displacement. Graphic abstract Highlights The difference in shape of relative permeability curves are indicative of the effect of mobility control of each polymer concentration. The water-oil systems exhibited oil-wet characteristics, while the polymer-oil systems demonstrated water-wet characteristics. A large contrast in displacing and displaced fluid viscosities led to viscous fingering and early water breakthrough.

An Easy Calculation Method on Sweep Efficiency of Chemical Flooding

2013 ◽  
Vol 275-277 ◽  
pp. 496-501
Author(s):  
Fu Qing Yuan ◽  
Zhen Quan Li
Keyword(s):  
Oil Recovery ◽  
Orthogonal Design ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Solution Viscosity ◽  
Chemical Flooding ◽  
Oil Viscosity ◽  
Sweep Efficiency ◽  
Easy Calculation ◽  
Polymer Compound

According to the geological parameters of Shengli Oilfield, sweep efficiency of chemical flooding was analyzed according to injection volume, injection-production parameters of polymer flooding or surfactant-polymer compound flooding. The orthogonal design method was employed to select the important factors influencing on expanding sweep efficiency by chemical flooding. Numerical simulation method was utilized to analyze oil recovery and sweep efficiency of different flooding methods, such as water flooding, polymer flooding and surfactant-polymer compound flooding. Finally, two easy calculation models were established to calculate the expanding degree of sweep efficiency by polymer flooding or SP compound flooding than water flooding. The models were presented as the relationships between geological parameters, such as effective thickness, oil viscosity, porosity and permeability, and fluid parameters, such as polymer-solution viscosity and oil-water interfacial tension. The precision of the two models was high enough to predict sweep efficiency of polymer flooding or SP compound flooding.

Sign in / Sign up

Export Citation Format

Share Document