scholarly journals Synthesis by Thermal Oxidation and Gas Sensing Properties of Fe2O3 Nanorods

2021 ◽  
Vol 31.2 (149) ◽  
pp. 84-88
Keyword(s):  
Thermal Oxidation ◽  
Gas Sensing ◽  
High Sensitivity ◽  
Measuring System ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Properties ◽  
Oxide Nanorods ◽  
Gas Sensing Properties ◽  
Sensitivity And Selectivity

Iron oxide nanorods were synthesized by thermal oxidation of iron foil in the air at 300-500 oC. The scanning electron microscopy (SEM) and X-ray diffraction (XRD) were used to investigate the crystal structures and morphologies properties of the Fe2O3 nanorods. The gas sensing properties of the Fe2O3 nanorods were investigated using a static-gas measuring system in a range of 300-500 oC with the target gases of C2H5OH, CH3COCH3, LPG, and NH3. The results show that Fe2O3 nanorods possess high sensitivity and selectivity toward CH3COCH3. The highest response of 19 was recorded with 1000 ppm CH3COCH3 at the operating temperature of 400 oC.

Polyaniline/SnO2 Nanocomposite Sensor for NO2 Gas Sensing at Low Operating Temperature

2015 ◽  
Vol 14 (04) ◽  
pp. 1550011 ◽  
Author(s):  
A. Sharma ◽  
M. Tomar ◽  
V. Gupta ◽  
A. Badola ◽  
N. Goswami
Keyword(s):  
Thin Films ◽  
Gas Sensing ◽  
High Sensitivity ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Chemical Route ◽  
Sensing Properties ◽  
Response Recovery ◽  
Transmission Electron ◽  
Gas Sensing Properties

In this paper gas sensing properties of 0.5–3% polyaniline (PAni) doped SnO 2 thin films sensors prepared by chemical route have been studied towards the trace level detection of NO 2 gas. The structural, optical and surface morphological properties of the PAni doped SnO 2 thin films were investigated by performing X-ray diffraction (XRD), Transmission electron microscopy (TEM) and Raman spectroscopy measurements. A good correlation has been identified between the microstructural and gas sensing properties of these prepared sensors. Out of these films, 1% PAni doped SnO 2 sensor showed high sensitivity towards NO 2 gas along with a sensitivity of 3.01 × 102 at 40°C for 10 ppm of gas. On exposure to NO 2 gas, resistance of all sensors increased to a large extent, even greater than three orders of magnitude. These changes in resistance upon removal of NO 2 gas are found to be reversible in nature and the prepared composite film sensors showed good sensitivity with relatively faster response/recovery speeds.

Au-sensitized WO3 nanoparticles synthesized and their enhanced acetone sensing properties

2018 ◽  
Vol 11 (04) ◽  
pp. 1850071 ◽  
Author(s):  
Dongping Xue ◽  
Zhanying Zhang
Keyword(s):  
Recovery Time ◽  
Gas Sensing ◽  
Test Results ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Properties ◽  
Response Recovery ◽  
Two Samples ◽  
Gas Sensing Properties ◽  
Scanning Electron

Au-sensitized WO3 nanoparticles have been synthesized by a facile two-step hydrothermal method. The structures, morphologies and surface compositions of the materials were characterized by X-ray diffraction (XRD), energy dispersive spectroscopy (EDS) and scanning electron microscopy (SEM). The test results show that we have prepared higher purity Au-sensitized WO3 nanoparticles. The gas-sensing properties of pure and Au-sensitized WO3 nanoparticles on acetone vapor were further investigated. The results obtained show that the response-recovery time of the two samples prepared is relatively short compared to that reported in the current literature. The Au-sensitized WO3 nanoparticles are significantly more sensitive and selective than the pure WO3 nanoparticles. This may be mainly attributed to the synergy between Au and WO3. It is expected that the Au-sensitized WO3 nanoparticles thus prepared can also be used for research in other fields.

Synthesis and Gas Sensing Properties of SnO2-CuO Nanocomposites

2013 ◽  
Vol 645 ◽  
pp. 129-132 ◽  
Author(s):  
Jantasom Khanidtha ◽  
Suttinart Noothongkaew ◽  
Supakorn Pukird
Keyword(s):  
Room Temperature ◽  
Gas Sensing ◽  
Precipitation Method ◽  
Monoclinic Structure ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Sensing Properties ◽  
Gas Sensing Properties ◽  
Co Precipitation

SnO2-CuO nanocomposites have been synthesized with the simple co-precipitation method for gas sensing properties. Sn and CuO powder were the starting materials. The synthesized products were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that SnO2-CuO nanocomposites have a tetragonal and monoclinic structure, respectively. SEM images verify that the some microballs are up to 10 µm and nanorods have a diameter range from 10-100 nm, while length ranges a few micrometers. The nanocomposite products were highly sensitivity to CO2gas at room temperature.

Preparation and Gas Sensing Properties of Hierarchical Flower-Shaped Bi2WO6

2016 ◽  
Vol 69 (1) ◽  
pp. 107 ◽  
Author(s):  
Jingkun Xiao ◽  
Chengwen Song ◽  
Wei Dong ◽  
Yanyan Yin ◽  
Chen Li
Keyword(s):  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Fast Response ◽  
X Ray Diffraction ◽  
Fast Recovery ◽  
X Ray ◽  
Sensing Properties ◽  
Sensing System ◽  
Gas Sensing Properties ◽  
20 Nm

Hierarchical flower-shaped Bi2WO6 was obtained by a simple hydrothermal method. Morphology and structure of the Bi2WO6 were characterised by single electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and N2 adsorption techniques. Gas sensing properties of the Bi2WO6 sensor were investigated by a static gas-sensing system. The results show the as-synthesised flower-shaped product is pure orthorhombic Bi2WO6, which is composed of nanosheets with ~10–20 nm in thickness and hundreds of nanometres in planar size. At this optimal operating temperature of 300°C, the Bi2WO6 sensor exhibits ultra-fast response (1-2 s) and fast recovery time (6–12 s) towards ethanol detection, and high selectivity to other gases such as methanol, benzene, dichloromethane, and hexane.

The Characterization and Gas Sensing Properties of Polythiophene Coated V2O5 Nanotubes

2010 ◽  
Vol 654-656 ◽  
pp. 1154-1157 ◽  
Author(s):  
Yu Lu ◽  
Wei Jin ◽  
Wen Chen
Keyword(s):  
Electron Microscopy ◽  
Gas Sensing ◽  
In Situ Polymerization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Properties ◽  
Transmission Electron ◽  
Gas Sensing Properties ◽  
Higher Sensitivity

Polythiophene (PTP) coated V2O5 nanotubes were prepared by an in-situ polymerization of thiophene monomers in the presence of prepared V2O5 nanotubes. The nanotubes were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), which proved the polymerization of thiophene monomer and the strong interaction between polythiophene and V2O5 nanotubes (VONTs). The gas sensing properties of PTP coated V2O5 nanotubes were studied at room temperature, which was found that PTP coated V2O5 nanotubes could detect ethanol with much higher sensitivity than pure VONTs. The sensing mechanism of PTP coated V2O5 nanotubes to ethanol is presumed to be the synergetic interaction between polythiophene (PTP) and V2O5 nanotubes.

Simple Synthesis of Mesoporous SnO2 Microspheres and their Gas Sensing Properties

2014 ◽  
Vol 1044-1045 ◽  
pp. 96-99
Author(s):  
Zhi Peng Sun ◽  
Yi Lu
Keyword(s):  
Electron Microscope ◽  
Gas Sensing ◽  
Resorcinol Formaldehyde ◽  
X Ray ◽  
Sensing Properties ◽  
Transmission Electron ◽  
Gas Sensing Properties ◽  
Sensitivity And Selectivity ◽  
20 Nm ◽  
Tin Tetrachloride

In this work, uniform mesoporous SnO2microspheres have been prepared via a facile and scalable method using tin tetrachloride pentahydrate (SnCl4·5H2O) and resorcinol-formaldehyde gel (RF gel) as starting materials. Furthermore, the structure and morphology of the as-prepared product were characterized by scanning electron microscope (SEM), Transmission electron microscope (TEM) and X-ray diffractometer (XRD). The results revealed that as-synthesized microspheres were around 500 nm in size and composed of large amount of SnO2nanoparticles with diameters of 10-20 nm. Gas sensors based on mesoporous SnO2microspheres were fabricated, and their gas sensing properties were tested for response to methane, butane, H2and CO gas. The sensor exhibited better sensitivity and selectivity to H2vapors at 300 °C than that of the conventional SnO2materials. The enhancement in gas sensing properties was attributed to their unique nanostructures.

Gas Sensing Properties of ZnO Thin Film/Si Heterojunction to Alcohols

2011 ◽  
Vol 687 ◽  
pp. 798-802
Author(s):  
Xiao Yan Zhou ◽  
Ming Ma ◽  
Qing Zhong Xue
Keyword(s):  
Gas Sensing ◽  
Rf Magnetron Sputtering ◽  
Volume Effect ◽  
X Ray Diffraction ◽  
Zno Film ◽  
X Ray ◽  
Sensing Properties ◽  
Current Voltage ◽  
Gas Sensing Properties ◽  
Chain Lengths

The polycrystalline zinc oxide (ZnO) film was deposited on p-Si substrate by radio-frequency (RF) magnetron sputtering. The structure and morphology of the ZnO thin films are characterized by X-ray diffraction (XRD), the energy dispersive analysis of X-ray (EDX) and scanning electron microscope (SEM). The gas sensing properties of the ZnO/Si heterojunctions for alcohols with different chain lengths were investigated at room temperature. It is found that the current-voltage (I-V) characteristics of the ZnO/Si heterojunctions are sensitive to isopropanol, ethanol and methanol gas. We discussed a possible gas sensing mechanism of ZnO/Si heterojunction. The sensitivity of the ZnO/Si heterojunctions to the gases decreases from isopropanol to methanol and to ethanol at the same concentration. It can be explained by the volume effect and electron donating effect.

Synthesis of H-In2O3 and C-In2O3 by Different Methods and Gas Sensing Properties

2011 ◽  
Vol 284-286 ◽  
pp. 1006-1009
Author(s):  
Bin Wang ◽  
Fu Bo Gu ◽  
Dong Mei Han ◽  
Guang Sheng Guo
Keyword(s):  
Gas Sensing ◽  
Diffraction Field ◽  
Solvothermal Process ◽  
X Ray Diffraction ◽  
Reaction Conditions ◽  
X Ray ◽  
Sensing Properties ◽  
Gas Sensing Properties ◽  
One Step ◽  
Scanning Electron

In(OH)3 and InOOH were prepared through a simple hydrothermal method at different volume ratios of En and H2O. C-In2O3 and H-In2O3 were obtained by annealing these two precursors at 400°C in air, respectively. One-step In2O3 was also synthesized via solvothermal process using DEG as solvents. The effects of reaction conditions on phase structures and morphologies were studied. The gas sensing properties of the obtained materials toward ethanol were measured and X-ray diffraction, field-emission scanning electron microscope and PL were used to characterize the as-obtained products.

Schottky diodes based on 2D materials for environmental gas monitoring: a review on emerging trends, recent developments and future perspectives

2021 ◽  
Author(s):  
Minu Mathew ◽  
Chandra Sekhar Rout
Keyword(s):  
Gas Sensing ◽  
2D Materials ◽  
Schottky Diodes ◽  
High Sensitivity ◽  
Future Perspectives ◽  
Working Temperature ◽  
Emerging Trends ◽  
Gas Sensing Properties ◽  
Recent Developments ◽  
Sensitivity And Selectivity

This review details the fundamentals, working principles and recent developments of Schottky junctions based on 2D materials to emphasize their improved gas sensing properties including low working temperature, high sensitivity, and selectivity.

scholarly journals Preparation of Nanostructured SnO2-NiO Composite Semiconductor for Gas Sensor Applications

2021 ◽  
pp. 391-403
Author(s):  
S. Kumar ◽  
P. Gowthaman ◽  
J. Deenathayalan
Keyword(s):  
Gas Sensor ◽  
Composite Nanofibers ◽  
Volume Fraction ◽  
Gas Sensing ◽  
Precipitation Method ◽  
Response Sensitivity ◽  
X Ray ◽  
Sensing Properties ◽  
Working Temperature ◽  
Gas Sensing Properties

Electro spinning technology combined with chemical precipitation method and high-temperature calcination was used to prepare SnO2-NiO composite semiconductor nanofibers with different Sn content. Scanning electron microscope (SEM), X-ray diffractometer (XRD) and energy dispersive X-ray spectrometer (EDS) were used to characterize the morphology, structure and content of various elements of the sample. Using ethanol as the target gas, the gas sensing properties of SnO2-NiO nanofibers and the influence of Sn content on the gas sensing properties of composite nanofibers were explored. The research results show that SnO2-NiO composite nanofibers have a three-dimensional network structure, and the SnO2 composite can significantly enhance the gas sensitivity of NiO nanofibers. With increase of SnO2 content, the response sensitivity of composite fibers to ethanol gas increases, and the response sensitivity of composite nanofibers with the highest response to ethanol gas with a volume fraction of 100×10-6 at the optimal working temperature of 160℃ are13.4;It is 8.38 times the maximum response sensitivity of NiO nanofibers. Compared with the common ethanol gas sensor MQ-3 on the market, SnO2-NiO composite nanofibers have a lower optimal working temperature and higher response sensitivity, which has certain practical application value

Sign in / Sign up

Export Citation Format

Share Document