scholarly journals Damage sensing and mechanical properties of a laminate composite material containing MWCNTs during low-velocity impact

2020 ◽  
Vol 10 (4) ◽  
pp. 147-164
Author(s):  
Mohammed Al-Bahrani ◽  
Mohammed Ridh H. Alhakeem ◽  
Alistair Cree
Keyword(s):  
Composite Material ◽  
Impact Energy ◽  
Electrical Resistance ◽  
Impact Load ◽  
Fibre Composite ◽  
Low Velocity Impact ◽  
High Concentration ◽  
Low Velocity ◽  
Velocity Impact ◽  
Conductivity Property

In this work, we present a new criterion, unlike other attempts, to evaluate and quantify the degree of damage of composite material when it subjected to a sudden impact load. Our criterion exploits the high intrinsic electrical conductivity property of the Multi-walled carbon nanotubes (MWCNTs) after dispersing different concentrations of them (0, 0.5, 1.0, 1.5 and 2.0 %) in the epoxy matrix of a glass fibre composite. Following this goal, the low-velocity impact and flexural after impact (FAI) tests on the MWCNTs-glass epoxy (i.e. MWCNTs-GF) nanocomposite were evaluated. At the same time, the changes in its electrical resistance were measured. The results showed that the properties of the self-sensing composites were significantly affected by impact energy. The damage after impact causes an increase in the electrical resistance of the MWCNTs-GF nanocomposite and increases with increased impact energy. In addition, the samples containing a high concentration of MWCNTs showed lower damage sensitivity under all impact energies levels as compared with the samples contain a lower MWCNTs concentration. Therefore, the results presented in this work have shown that it is possible to associate the change in electrical resistance of the MWCNTs-GF nanocomposite with the degree of damages caused by impact load.

scholarly journals The Study of Impact Behaviour of Two Types of Glass Fibre Reinforced Polymer (GFRP) Subjected to Low Velocity Impact

2014 ◽  
Vol 1044-1045 ◽  
pp. 153-157 ◽  
Author(s):  
N. Razali ◽  
M.T.H. Sultan ◽  
Y. Aminanda
Keyword(s):  
Composite Material ◽  
Impact Energy ◽  
Glass Fibre ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
Reinforced Polymer ◽  
Glass Fibre Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Glass Fibre Reinforced

The aim of this work is to study the behaviour of two types of composite material when subjected to impacts at different energy levels under low velocity impact events. The composite material used in this study was Glass Fibre Reinforced Polymer (GFRP) which was C-type/600 g/m2 and E-type/600 g/m2. This material was fabricated to produce laminated plate specimens with a dimension of 100 mm 150 mm. Each specimen had 10 layers of GFRP woven roving plies. The low velocity impact test was performed using an IM10 Drop Weight Impact Tester with a 10 mm hemispherical striker cap. The impact energy was set to 14, 28, 42 and 56 joules with velocity ranging from 1.73 m/s to 3.52 m/s. The relationships of impact energy with impact force, displacement and energy absorbed are presented. The comparison and behaviour between the two types of GFRP are discussed.

scholarly journals Low-Velocity Impact Resistance of Al/Gf/PP Laminates with Different Interface Performance

Polymers ◽  
2021 ◽  
Vol 13 (24) ◽  
pp. 4416
Author(s):  
Yanyan Lin ◽  
Huaguan Li ◽  
Zhongwei Zhang ◽  
Jie Tao
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Impact Load ◽  
Rear Surface ◽  
Impact Resistance ◽  
Nitrogen Plasma ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
The Impact

The weak interface performance between metal and composite (IPMC) makes the composite materials susceptible to impact load. Aluminum/glass fiber/polypropylene (Al/Gf/PP) laminates were manufactured with the aluminum alloy sheets modified by nitrogen plasma surface treatment and the phosphoric acid anodizing method, respectively. FEM models of Al/Gf/PP laminates under low-velocity impact were established in ABAQUS/Explicit based on the generated data including the model I and II interlaminar fracture toughness. Low-velocity impact tests were performed to investigate the impact resistance of Al/Gf/PP laminates including load traces, failure mechanism, and energy absorption. The results showed that delamination was the main failure mode of two kinds of laminates under the impact energy of 20 J and 30 J. When the impact energy was between 40 J and 50 J, there were metal cracks on the rear surface of the plasma pretreated specimens, which possessed higher energy absorption and impact resistance, although the integrity of the laminates could not be preserved. Since the residual compressive stress was generated during the cooling process, the laminates were more susceptible to stretching rather than delamination. For impact energy (60 J) causing the through-the-thickness crack of two kinds of laminates, plasma pretreated specimens exhibited higher SEA values close to 9 Jm2/kg due to better IPMC. Combined with the FEM simulation results, the interface played a role in stress transmission and specimens with better IPMC enabled the laminates to absorb more energy.

scholarly journals Impact Response and Damage Characteristics of Carbon Fiber Reinforced Aluminum Laminates Under Low Velocity Impact Loading

2020 ◽  
Vol 9 (4) ◽  
pp. 1831-1837
Keyword(s):  
Impact Energy ◽  
Impact Load ◽  
Three Dimensional ◽  
Low Velocity Impact ◽  
Fe Model ◽  
Low Velocity ◽  
Fiber Layer ◽  
Cross Sectional ◽  
Velocity Impact ◽  
The Impact

CARALL hybrid material has been extensively used in the aircraft structure due to their competitive impact strength. Low velocity impact test is utilized to evaluate the impact and damage properties for such material. It is also employed to observe complex damage mechanisms. A numerical modelling is an alternative way for impact assessment. This paper investigates the impact and damage properties under low velocity impact using numerical modeling and experimental work. A three-dimensional (3D) finite element (FE) model was devolved and validated with two studies from the literature. This model was meshed with solid elements. It was subjected to 2.4 m/s impact velocity and to 10 J impact energy. Absorbed energy, penetration, impact load and damage morphology were obtained. The impact energy was efficiently absorbed by the material. Both aluminum alloy layers underwent plastic deformation whereas the fiber layer failed. A macroscopic cross-sectional morphology was presented using the FE model. An agreement between the numerical and the experiment results were achieved and discussed.

scholarly journals Effect of Weaving Type on Damage Behaviour of Carbon/Epoxy Laminate under Low Velocity Impact Loading

2017 ◽  
Vol 61 (2) ◽  
pp. 140 ◽  
Author(s):  
Djilali Beida Maamar ◽  
Ramdane Zenasni
Keyword(s):  
Finite Element ◽  
Composite Material ◽  
Impact Load ◽  
Low Velocity Impact ◽  
The Finite Element Method ◽  
Low Velocity ◽  
Velocity Impact ◽  
Rigid Body Model ◽  
The Matrix ◽  
Finite Element Package

The main purpose of the present investigation was to determine the damages generated by the low velocity impact by mean of the finite element method. The commercial transient finite element package LS-dyna used to model the effect of slug impactor induced damage in composite material subjected to low velocity impact. Four types of weaving were considered; serge (2/2), serge (0/30/-30/0), serge (0/45-45/0) and taffeta. The Texgen package was used to build the laminate pattern weaves. The composite material was subjected to stainless steel slug impactor in the transverse direction dropping the composite laminate at the center with a velocity about of 15m/s. The analysis was carried out using the model 001-ELASTIC for matrix, 002-ORTHOTROPIC_ELASTIC for fibersand a rigid body model MAT20 for the slug impactor. The contact automatic single surface has been used between the yarns and the automatic_surface_to_surface between the matrix and the impactor and the contact automatic_surface_to_surface_tiebreak between the matrix and yarns and the contact automatic_surface_to_surface_tiebreak between layers.The impact load, energy, displacements were reported as function of impact time. The delamination area was represented at the layer interfaces for each material.

Response and failure modes of biaxial warp-knitted flexible composite subject to low-velocity impact

2021 ◽  
pp. 152808372110154
Author(s):  
Ziyu Zhao ◽  
Tianming Liu ◽  
Pibo Ma
Keyword(s):  
Impact Energy ◽  
Linear Density ◽  
Failure Modes ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Minor Effect ◽  
Low Velocity ◽  
Velocity Impact ◽  
Flexible Composites ◽  
The Impact

In this paper, biaxial warp-knitted fabrics were produced with different high tenacity polyester linear density and inserted yarns density. The low-velocity impact property of flexible composites made of polyurethane as matrix and biaxial warp-knitted fabric as reinforcement has been investigated. The effect of impactor shape and initial impact energy on the impact response of flexible composite is tested. The results show that the initial impact energy have minor effect on the impact response of the biaxial warp-knitted flexible composites. The impact resistance of flexible composite specimen increases with the increase of high tenacity polyester linear density and inserted yarns density. The damage morphology of flexible composite materials is completely different under different impactor shapes. The findings have theoretical and practical significance for the applications of biaxial warp-knitted flexible composite.

Effect of SiO2 Nanoparticles on the Mechanical and Low Velocity Impact Properties of Epoxy/Glass Composites

2016 ◽  
Vol 838 ◽  
pp. 29-35
Author(s):  
Michał Landowski ◽  
Krystyna Imielińska
Keyword(s):  
Flexural Strength ◽  
Energy Absorption ◽  
Impact Energy ◽  
Epoxy Matrix ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Nanoparticle Suspension ◽  
Impact Properties ◽  
Velocity Impact ◽  
The Impact

Flexural strength and low velocity impact properties were investigated in terms of possibile improvements due to epoxy matrix modification by SiO2 nanoparticles (1%, 2%, 3%, 5%, 7%wt.) in glass/epoxy laminates formed using hand lay-up method. The matrix resin was Hexion L285 (DGEBA) with Nanopox A410 - SiO2 (20 nm) nanoparticle suspension in the base epoxy resin (DGEBA) supplied by Evonic. Modification of epoxy matrix by variable concentrations of nanoSiO2 does not offer significant improvements in the flexural strength σg, Young’s modulus E and interlaminar shear strength for 1% 3% and 5% nanoSiO2 and for 7% a slight drop (up to ca. 15-20%) was found. Low energy (1J) impact resistance of nanocomposites represented by peak load in dynamic impact characteristics was not changed for nanocompoosites compared to the unmodified material. However at higher impact energy (3J) nanoparticles appear to slightly improve the impact energy absorption for 3% and 5%. The absence or minor improvements in the mechanical behaviour of nanocomposites is due to the failure mechanisms associated with hand layup fabrication technique: (i.e. rapid crack propagation across the extensive resin pockets and numerous pores and voids) which dominate the nanoparticle-dependent crack energy absorption mechanisms (microvoids formation and deformation).

scholarly journals Mechanical Characterization and Impact Damage Assessment of Hybrid Three-Dimensional Five-Directional Composites

Polymers ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1395 ◽  
Author(s):  
Liwei Wu ◽  
Wei Wang ◽  
Qian Jiang ◽  
Chunjie Xiang ◽  
Ching-Wen Lou
Keyword(s):  
Carbon Fiber ◽  
Impact Load ◽  
Hybrid Composites ◽  
Impact Damage ◽  
Three Dimensional ◽  
Low Velocity Impact ◽  
Aramid Fibers ◽  
Braided Composites ◽  
Low Velocity ◽  
Velocity Impact

The effects of braided architecture and co-braided hybrid structure on low-velocity response of carbon-aramid hybrid three-dimensional five-directional (3D5d) braided composites were experimentally investigated in this study. Low-velocity impact was conducted on two types of hybridization and one pure carbon fiber braided reinforced composites under three velocities. Damage morphologies after low-velocity impact were detected by microscopy and ultrasonic nondestructive testing. Interior damages of composites were highly dependent on yarn type and alignment. Impact damage tolerance was introduced to evaluate the ductility of hybrid composites. Maximum impact load and toughness changed with impact velocity and constituent materials of the composites. The composite with aramid fiber as axial yarn and carbon fiber as braiding yarn showed the best impact resistance due to the synergistic effect of both materials. Wavelet transform was applied in frequency and time domain analyses to reflect the failure mode and mechanism of hybrid 3D5d braided composites. Aramid fibers were used either as axial yarns or braiding yarns, aiding in the effective decrease in the level of initial damage. In particular, when used as axial yarns, aramid fibers effectively mitigate the level of damage during damage evolution.

scholarly journals Low-Velocity Impact Load Testing of RC Beams Strengthened in Flexure with Bonded FRP Sheets

2020 ◽  
Vol 24 (5) ◽  
pp. 04020036 ◽  
Author(s):  
Norimitsu Kishi ◽  
Masato Komuro ◽  
Tomoki Kawarai ◽  
Hiroshi Mikami
Keyword(s):  
Impact Load ◽  
Low Velocity Impact ◽  
Rc Beams ◽  
Load Testing ◽  
Low Velocity ◽  
Velocity Impact
Sign in / Sign up

Export Citation Format

Share Document