scholarly journals A Low-Power, High-Gain Amplifier with Rail-to-Rail Operating Capability: Applications to Biomedical Signal Processing

2021 ◽  
Vol 58 (1) ◽  
pp. 71-76
Author(s):  
Hassan Faraji Baghtash ◽  
Rasoul Pakdel
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Process Variations ◽  
High Gain ◽  
Biomedical Signal Processing ◽  
Noise Power ◽  
Well Performance ◽  
Subthreshold Region ◽  
Rail To Rail ◽  
Unity Gain

low-voltage, low-power, rail-to-rail, two-stage trans-conductance amplifier is presented. The structure exploits body-driven transistors, configured in folded-cascode structure. To reduce the power consumption, the transistors are biased in the subthreshold region. The Specter RF simulation results which are conducted in TSMC 180nm CMOS standard process proves the well-performance of the proposed structure. The performance of the proposed structure against process variations is checked through process corners and Monte Carlo simulations. The results prove the robustness of the proposed amplifier against process uncertainties. Some important specifications of the design derived from circuit simulations are 93.36 dB small-signal gain, 14.4 PV2/Hz input referred noise power, 26.5 kHz unity gain frequency, 20 V/ms slew rate. The proposed structure draws 260 nW power from 0.5 V power supply and is loaded with a 15 pF loading capacitor. The input common mode range of structure is from 0 to 0.5 V.

Analysis and design of ultra-low-voltage low-power rail-to-rail VCO-based comparator in subthreshold region

2019 ◽  
Vol 84 ◽  
pp. 106-114 ◽  
Author(s):  
Saeideh Kabirpour ◽  
Mohsen Jalali
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Subthreshold Region ◽  
Analysis And Design ◽  
Rail To Rail

COMPOSITE TRANSISTOR CELL USING DYNAMIC BODY BIAS FOR HIGH GAIN AND LOW-VOLTAGE APPLICATIONS

2014 ◽  
Vol 23 (08) ◽  
pp. 1450108 ◽  
Author(s):  
VANDANA NIRANJAN ◽  
ASHWANI KUMAR ◽  
SHAIL BALA JAIN
Keyword(s):  
Low Power ◽  
Large Scale ◽  
Low Voltage ◽  
Supply Voltage ◽  
High Gain ◽  
Signal Frequency ◽  
Output Impedance ◽  
Self Cascode ◽  
Intrinsic Gain ◽  
Body Bias

In this work, a new composite transistor cell using dynamic body bias technique is proposed. This cell is based on self cascode topology. The key attractive feature of the proposed cell is that body effect is utilized to realize asymmetric threshold voltage self cascode structure. The proposed cell has nearly four times higher output impedance than its conventional version. Dynamic body bias technique increases the intrinsic gain of the proposed cell by 11.17 dB. Analytical formulation for output impedance and intrinsic gain parameters of the proposed cell has been derived using small signal analysis. The proposed cell can operate at low power supply voltage of 1 V and consumes merely 43.1 nW. PSpice simulation results using 180 nm CMOS technology from Taiwan Semiconductor Manufacturing Company (TSMC) are included to prove the unique results. The proposed cell could constitute an efficient analog Very Large Scale Integration (VLSI) cell library in the design of high gain analog integrated circuits and is particularly interesting for biomedical and instrumentation applications requiring low-voltage low-power operation capability where the processing signal frequency is very low.

scholarly journals A 0.3 V Rail-to-Rail Ultra-Low-Power OTA with Improved Bandwidth and Slew Rate

2021 ◽  
Vol 11 (2) ◽  
pp. 19
Author(s):  
Francesco Centurelli ◽  
Riccardo Della Sala ◽  
Pietro Monsurrò ◽  
Giuseppe Scotti ◽  
Alessandro Trifiletti
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Process ◽  
Slew Rate ◽  
Large Signal ◽  
Output Stage ◽  
Ultra Low Power ◽  
Input Stage ◽  
Rail To Rail

In this paper, we present a novel operational transconductance amplifier (OTA) topology based on a dual-path body-driven input stage that exploits a body-driven current mirror-active load and targets ultra-low-power (ULP) and ultra-low-voltage (ULV) applications, such as IoT or biomedical devices. The proposed OTA exhibits only one high-impedance node, and can therefore be compensated at the output stage, thus not requiring Miller compensation. The input stage ensures rail-to-rail input common-mode range, whereas the gate-driven output stage ensures both a high open-loop gain and an enhanced slew rate. The proposed amplifier was designed in an STMicroelectronics 130 nm CMOS process with a nominal supply voltage of only 0.3 V, and it achieved very good values for both the small-signal and large-signal Figures of Merit. Extensive PVT (process, supply voltage, and temperature) and mismatch simulations are reported to prove the robustness of the proposed amplifier.

scholarly journals A Low-power High-gain Inverter Stacking Amplifier with Rail-to-Rail Output

2021 ◽  
Author(s):  
Erwin H. T. Shad ◽  
Tania Moeinfard ◽  
Marta Molinas ◽  
Trond Ytterdal
Keyword(s):  
Low Power ◽  
High Gain ◽  
Rail To Rail

scholarly journals A 2.5 Gbps, 10-Lane, Low-Power, LVDS Transceiver in 28 nm CMOS Technology

Electronics ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 350 ◽  
Author(s):  
Xu Bai ◽  
Jianzhong Zhao ◽  
Shi Zuo ◽  
Yumei Zhou
Keyword(s):  
Low Power ◽  
High Speed ◽  
Low Voltage ◽  
Cmos Technology ◽  
Common Mode ◽  
Serial Interface ◽  
Common Mode Voltage ◽  
Rail To Rail ◽  
The Common ◽  
28 Nm

This paper presents a 2.5 Gbps 10-lane low-power low voltage differential signaling (LVDS) transceiver for a high-speed serial interface. In the transmitter, a complementary MOS H-bridge output driver with a common mode feedback (CMFB) circuit was used to achieve a stipulated common mode voltage over process, voltage and temperature (PVT) variations. The receiver was composed of a pre-stage common mode voltage shifter and a rail-to-rail comparator. The common mode voltage shifter with an error amplifier shifted the common mode voltage of the input signal to the required range, thereby the following rail-to-rail comparator obtained the maximum transconductance to recover the signal. The chip was fabricated using SMIC 28 nm CMOS technology, and had an area of 1.46 mm2. The measured results showed that the output swing of the transmitter was around 350 mV, with a root-mean-square (RMS) jitter of 3.65 [email protected] Gbps, and the power consumption of each lane was 16.51 mW under a 1.8 V power supply.

Low-voltage, Low-power and High-gain Mixer Based on Unbalanced Mixer Cell

2006 ◽  
Author(s):  
No Myoung ◽  
Ho Kang ◽  
Seok Kim ◽  
Byoung Choi ◽  
Seong-su Park ◽  
...  
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
High Gain
Sign in / Sign up

Export Citation Format

Share Document