The new generation of the biologicalengineering materials for applications in medical and dental implant-scaffolds

2018 ◽  
Vol 2 (91) ◽  
pp. 56-85 ◽  
Author(s):  
L.A. Dobrzański ◽  
A.D. Dobrzańska-Danikiewicz ◽  
Z.P. Czuba ◽  
L.B. Dobrzański ◽  
A. Achtelik-Franczak ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Dental Implant ◽  
Surface Engineering ◽  
Sol Gel ◽  
Dip Coating ◽  
Living Cells ◽  
Ti6al4v Alloy ◽  
Live Cells ◽  
Biological Engineering ◽  
Processing Technologies

Purpose: The publication aims to find the relationship between the proliferation of surface layers of living cells and the deposition of thin atomic layers deposition ALD coatings on the pores internal surfaces of porous skeletons of medical and dental implant-scaffolds manufactured with the selective laser deposition SLS additive technology using titanium and Ti6Al4V alloy. Design/methodology/approach: The extensive review of the literature presents the state-of-the-art in the field of regenerative medicine and tissue engineering. General ageing of societies, increasing the incidence of oncological diseases and some transport and sports accidents, and also the spread of tooth decay and tooth cavities in many regions of the world has taken place nowadays. Those reasons involve resection of many tissues and organs and the need to replace cavities, among others bones and teeth through implantation, more and more often hybridized with tissue engineering methods. Findings: The results of investigations of the structure and properties of skeleton microporous materials produced from titanium and Ti6Al4V alloy powders by the method of selective laser sintering have been presented. Particularly valuable are the original and previously unpublished results of structural research using high-resolution transmission electron microscope HRTEM. Particular attention has been paid to the issues of surface engineering, in particular, the application of flat TiO2 and Al2O3 coatings applied inside micropores using the atomic layers deposition ALD method and hydroxyapatite applied the dip-coating sol-gel method, including advanced HRTEM research. The most important part of the work concerns the research of nesting and proliferation of live cells of osteoblasts the hFOB 1.19 (Human ATCC - CRL - 11372) culture line on the surface of micropores with surfaces covered with the mentioned layers. Research limitations/implications: The investigations reported in the paper fully confirmed the idea of the hybrid technology of producing microporous implants and implant-scaffolds to achieve original Authors’ biological-engineering materials. The surface engineering issues, including both flat-layered nonorganic coatings and interactions of those coverings with flat layers of living cells, play a crucial role. Originality/value: Materials commonly used in implantology and the most commonly used materials processing technologies in those applications have been described. Against that background, the original Authors' concept of implant-scaffolds and the application of microporous skeleton materials for this purpose have been presented.

Effects of Process Parameters on Formation of Hybrid Tissue Constructs

2013 ◽  
Author(s):  
Karen Chang Yan ◽  
Pamela Hitscherich ◽  
James Ferrie
Keyword(s):  
Tissue Engineering ◽  
Processing Parameters ◽  
Living Cells ◽  
Live Cells ◽  
Solution Flow Rate ◽  
Electrospinning Technique ◽  
Solution Flow ◽  
Tissue Constructs ◽  
Key Issues ◽  
Working Distance

Tissue engineering is a promising aspect of regenerative medicine that is aimed at constructing functional tissues and organs. While progresses in tissue engineering have led successful clinic applications, challenges remain for more complex tissues/organs that require concerted efforts from multiple types of cells. One of the key issues in building replacements for complex tissues/organs is to mimic the organ’s complex natural organization using a mixture of engineered materials and living cells [1]. Electrospinning has shown promise as a technique to create the microenvironment necessary for cell growth and proliferation for tissue engineering applications[2–4], while multiple fabrication methods have been developed to manipulate live cells(e.g. cell printing) [5–7]. To this end, a system integrating polymer electrospinning technique and pressure-driven cell deposition method is currently under development for forming hybrid tissue constructs with living cells and polymers. This study focuses on examining morphology of electrospun fibers as function of processing parameters including working distance and solution flow rate.

4-dimensional, high-resolution imaging of living cells

1992 ◽  
Vol 50 (1) ◽  
pp. 416-417
Author(s):  
Shinya Inoué
Keyword(s):  
Light Microscope ◽  
Living Cells ◽  
Live Cells ◽  
Video Tape ◽  
Active Living ◽  
High Resolution Imaging ◽  
3 Dimensional ◽  
Dynamic Architecture ◽  
Resolution Imaging ◽  
Disk Memory

This paper reports progress of our effort to rapidly capture, and display in time-lapsed mode, the 3-dimensional dynamic architecture of active living cells and developing embryos at the highest resolution of the light microscope. Our approach entails: (A) real-time video tape recording of through-focal, ultrathin optical sections of live cells at the highest resolution of the light microscope; (B) repeat of A at time-lapsed intervals; (C) once each time-lapsed interval, an image at home focus is recorded onto Optical Disk Memory Recorder (OMDR); (D) periods of interest are selected using the OMDR and video tape records; (E) selected stacks of optical sections are converted into plane projections representing different view angles (±4 degrees for stereo view, additional angles when revolving stereos are desired); (F) analysis using A - D.

In-Situ Study of NiO Growth on Textured Nickel Tape Using Environmental Scanning Electron Microscope (ESEM) and Hot Stage

2001 ◽  
Vol 7 (S2) ◽  
pp. 1276-1277
Author(s):  
Y. Akin ◽  
R.E. Goddard ◽  
W. Sigmund ◽  
Y.S. Hascicek
Keyword(s):  
Buffer Layer ◽  
Lattice Mismatch ◽  
Sol Gel ◽  
Surface Oxidation ◽  
Dip Coating ◽  
Buffer Layers ◽  
Superconducting Film ◽  
Environmental Scanning ◽  
Cold Rolling And Annealing

Deposition of highly textured ReBa2Cu3O7−δ (RBCO) films on metallic substrates requires a buffer layer to prevent chemical reactions, reduce lattice mismatch between metallic substrate and superconducting film layer, and to prevent diffusion of metal atoms into the superconductor film. Nickel tapes are bi-axially textured by cold rolling and annealing at appropriate temperature (RABiTS) for epitaxial growth of YBa2Cu3O7−δ (YBCO) films. As buffer layers, several oxide thin films and then YBCO were coated on bi-axially textured nickel tapes by dip coating sol-gel process. Biaxially oriented NiO on the cube-textured nickel tape by a process named Surface-Oxidation- Epitaxy (SEO) has been introduced as an alternative buffer layer. in this work we have studied in situ growth of nickel oxide by ESEM and hot stage.Representative cold rolled nickel tape (99.999%) was annealed in an electric furnace under 4% hydrogen-96% argon gas mixture at 1050°C to get bi-axially textured nickel tape.

Porous Gel Coatings Obtained by Phase Separation in ORMOSIL System

2000 ◽  
Vol 628 ◽  
Author(s):  
Kazuki Nakanishi ◽  
Souichi Kumon ◽  
Kazuyuki Hirao ◽  
Hiroshi Jinnai
Keyword(s):  
Phase Separation ◽  
Reaction Time ◽  
Volume Fraction ◽  
Sol Gel ◽  
Reaction Times ◽  
Dip Coating ◽  
Coating Solution ◽  
Coating Method ◽  
Gel Phase ◽  
Dip Coating Method

ABSTRACTMacroporous silicate thick films were prepared by a sol-gel dip-coating method accompanied by the phase separation using methyl-trimethoxysilane (MTMS), nitric acid and dimethylformamide (DMF) as starting components. The morphology of the film varied to a large extent depending on the time elapsed after the hydrolysis until the dipping of the coating solution. On a glass substrate, the films prepared by early dipping had inhomogeneous submicrometer-sized pores on the surface of the film. At increased reaction times, relatively narrow sized isolated macropores were observed and their size gradually decreased with the increase of reaction time. On a polyester substrate, in contrast, micrometer-sized isolated spherical gel domains were homogeneously deposited by earlier dippings. With an increase of reaction time, the volume fraction of the gel phase increased, then the morphology of the coating transformed into co-continuous gel domains and macropores, and finally inverted into the continuous gel domains with isolated macropores. The overall morphological variation with the reaction time was explained in terms of the phase separation and the structure freezing by the forced gelation, both of which were induced by the evaporation of methanol during the dipping operation.

Characterization of UHMWPE- HAp coating produced by dip coating method on Ti6Al4V alloy

2021 ◽  
pp. 127091
Author(s):  
Gözde Çelebi Efe ◽  
Elif Yenilmez ◽  
İbrahim Altinsoy ◽  
Serbülent Türk ◽  
Cuma Bindal
Keyword(s):  
Dip Coating ◽  
Ti6al4v Alloy ◽  
Coating Method ◽  
Dip Coating Method

scholarly journals 3D super-resolved imaging in live cells using sub-diffractive plasmonic localization of hybrid nanopillar arrays

Nanophotonics ◽  
2020 ◽  
Vol 9 (9) ◽  
pp. 2847-2859
Author(s):  
Soojung Kim ◽  
Hyerin Song ◽  
Heesang Ahn ◽  
Seung Won Jun ◽  
Seungchul Kim ◽  
...  
Keyword(s):  
Signal To Noise Ratio ◽  
Imaging Techniques ◽  
Optical Loss ◽  
Super Resolution ◽  
Living Cells ◽  
Live Cells ◽  
Complex Biological System ◽  
Observation Volume ◽  
Resolution Imaging ◽  
Nanopillar Arrays

AbstractAnalysing dynamics of a single biomolecule using high-resolution imaging techniques has been had significant attentions to understand complex biological system. Among the many approaches, vertical nanopillar arrays in contact with the inside of cells have been reported as a one of useful imaging applications since an observation volume can be confined down to few-tens nanometre theoretically. However, the nanopillars experimentally are not able to obtain super-resolution imaging because their evanescent waves generate a high optical loss and a low signal-to-noise ratio. Also, conventional nanopillars have a limitation to yield 3D information because they do not concern field localization in z-axis. Here, we developed novel hybrid nanopillar arrays (HNPs) that consist of SiO2 nanopillars terminated with gold nanodisks, allowing extreme light localization. The electromagnetic field profiles of HNPs are obtained through simulations and imaging resolution of cell membrane and biomolecules in living cells are tested using one-photon and 3D multiphoton fluorescence microscopy, respectively. Consequently, HNPs present approximately 25 times enhanced intensity compared to controls and obtained an axial and lateral resolution of 110 and 210 nm of the intensities of fluorophores conjugated with biomolecules transported in living cells. These structures can be a great platform to analyse complex intracellular environment.

scholarly journals Aqueous Sol-Gel Synthesis of Different Iron Ferrites: From 3D to 2D

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1554
Author(s):  
Justinas Januskevicius ◽  
Zivile Stankeviciute ◽  
Dalis Baltrunas ◽  
Kęstutis Mažeika ◽  
Aldona Beganskiene ◽  
...  
Keyword(s):  
Magnetic Measurements ◽  
Substrate Surface ◽  
Sol Gel ◽  
Synthesis Method ◽  
Xrd Analysis ◽  
Dip Coating ◽  
Yttrium Iron ◽  
Iron Garnet ◽  
Dip Coating Technique ◽  
Sol Gel Synthesis

In this study, an aqueous sol-gel synthesis method and subsequent dip-coating technique were applied for the preparation of yttrium iron garnet (YIG), yttrium iron perovskite (YIP), and terbium iron perovskite (TIP) bulk and thin films. The monophasic highly crystalline different iron ferrite powders have been synthesized using this simple aqueous sol-gel process displaying the suitability of the method. In the next step, the same sol-gel solution was used for the fabrication of coatings on monocrystalline silicon (100) using a dip-coating procedure. This resulted, likely due to substrate surface influence, in all coatings having mixed phases of both garnet and perovskite. Thermogravimetric (TG) analysis of the precursor gels was carried out. All the samples were investigated by X-ray powder diffraction (XRD) analysis. The coatings were also investigated by scanning electron microscopy (SEM), atomic force microscopy (AFM) and Mössbauer spectroscopy. Magnetic measurements were also carried out.

scholarly journals Development of Adhesive, Bioactive and Antibacterial Titania Sol-Gel Coating on Titanium Substrate by Dip-Coating Technique

Coatings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 243
Author(s):  
Diana Horkavcová ◽  
Quentin Doubet ◽  
Gisèle Laure Lecomte-Nana ◽  
Eva Jablonská ◽  
Aleš Helebrant
Keyword(s):  
Simulated Body Fluid ◽  
Body Fluid ◽  
Sol Gel ◽  
Titanium Substrate ◽  
Dip Coating ◽  
Coating Technique ◽  
Metal Implants ◽  
Excellent Adhesion ◽  
Titania Sol ◽  
Dip Coating Technique

The sol-gel method provides a wide variety of applications in the medical field. One of these applications is the formation of coatings on the metal implants. The coatings containing specific additive can enhance or improve the existing surface properties of the substrate. In this work, titania sol-gel coatings were doped with two forms of silver (AgNO3, Ag3PO4) and synthetic hydroxyapatite and applied on the titanium samples by dip-coating technique. After drying and slow firing, all coatings were characterized with scanning electron microscopy. Thin coatings were successfully prepared with excellent adhesion to the substrate (measured by ASTM D 3359-2), despite cracks. Coatings containing silver and hydroxyapatite demonstrated a 100% antibacterial effect against Escherichia coli after 24 h. The bioactivity of the coatings containing hydroxyapatite tested in modified simulated body fluid under static-dynamic conditions was confirmed by bone-like hydroxyapatite precipitation. To better understand the interaction of the coatings with simulated body fluid (SBF), changes of Ca2+ and (PO4)3− ions concentrations and pH values were studied.

scholarly journals A rapid “on–off–on” mitochondria-targeted phosphorescent probe for selective and consecutive detection of Cu2+ and cysteine in live cells and zebrafish

RSC Advances ◽  
2021 ◽  
Vol 11 (13) ◽  
pp. 7610-7620 ◽  
Author(s):  
Peipei Deng ◽  
Yongyan Pei ◽  
Mengling Liu ◽  
Wenzhu Song ◽  
Mengru Wang ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Living Cells ◽  
Live Cells ◽  
Mitochondria Targeting

An iridium(iii) complex-based mitochondria targeting phosphorescent probe for selectively detecting Cu2+ and Cys in aqueous solution, living cells and zebrafish has been developed.

Photocatalytic Degradation of Methylene Blue by NiO Thin Films under Solar Light Irradiation

2019 ◽  
Vol 56 ◽  
pp. 152-157 ◽  
Author(s):  
Abdelouahab Noua ◽  
Hichem Farh ◽  
Rebai Guemini ◽  
Oussama Zaoui ◽  
Tarek Diab Ounis ◽  
...  
Keyword(s):  
Thin Films ◽  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Sol Gel ◽  
Visible Region ◽  
Optical Transmittance ◽  
Dip Coating ◽  
Light Irradiation ◽  
Solar Light ◽  
Solar Light Irradiation

Nickel oxide (NiO) thin films were successfully deposited by sol-gel dip-coating method on glass substrates. The structural, morphological and optical properties in addition to the photocatalytic activity of the prepared films were investigated. The results show that the films have a polycrystalline NiO cubic structure with dense NiO grains and average optical transmittance in the visible region. The photocatalytic properties of the films were studied through the degradation of methylene blue and 89% of degradation was achieved for 4.5h of solar light irradiation exposure which indicates the capability of NiO photocatalytic activity.

Sign in / Sign up

Export Citation Format

Share Document