HIGH-SPEED WAVE-PIERCING CATAMARAN GLOBAL LOADS DETERMINED BY FEA AND SEA TRIALS

2021 ◽  
Vol 161 (A2) ◽  
Author(s):  
I Almallah ◽  
J Lavroff ◽  
D S Holloway ◽  
M R Davis
Keyword(s):  
Finite Element ◽  
High Speed ◽  
Local Strain ◽  
Element Model ◽  
Sensor Data ◽  
Design Stage ◽  
High Speeds ◽  
Design Loads ◽  
Hull Forms

Wave-piercing catamaran hull forms are widely used for high-speed ferry applications due to the hull slenderness, suitable for achieving high speeds. The global loads acting on these craft are of great interest as there is limited knowledge on determining the magnitude of the loads, in particular when operating in random sea conditions. Longitudinal and transverse bending moments as well as pitch connecting moments and hull torsion loads act on the hull simultaneously. This paper investigates the estimation of these global loads from full-scale catamaran sea trials strain gauge data using finite element methods. Det Norske Veritas (DNV) load cases are applied to a finite element model in order to determine the conversion between local strain values observed during sea trials and prevailing global loads. Comparisons are thus made of global loads determined from strain data collected from sea trials with DNV global load cases. The results show that this method is relatively reliable for the prediction of hull global loads in the absence of slamming. Comparisons have been made for different heading angles. The quasi-static design loads are important during the ship design stage, as they are good proxies in wavelengths comparable to the hull length for rationally determined loads obtained from a first-principles dynamic analysis. The broad aims here are to demonstrate the use of strain sensor data obtained during sea trials for determination of global sea loads, to reconcile the loads thus determined with DNV load cases and thereby to improve the accuracy of the predicted loads used in design to increase the structural efficiency of vessel design.

High-Speed Wave-Piercing Catamaran Global Loads Determined by FEA and Sea Trials

2019 ◽  
Vol 161 (A2) ◽  
Keyword(s):  
Finite Element ◽  
High Speed ◽  
Local Strain ◽  
Element Model ◽  
Sensor Data ◽  
Design Stage ◽  
High Speeds ◽  
Design Loads ◽  
Hull Forms

Wave-piercing catamaran hull forms are widely used for high-speed ferry applications due to the hull slenderness, suitable for achieving high speeds. The global loads acting on these craft are of great interest as there is limited knowledge on determining the magnitude of the loads, in particular when operating in random sea conditions. Longitudinal and transverse bending moments as well as pitch connecting moments and hull torsion loads act on the hull simultaneously. This paper investigates the estimation of these global loads from full-scale catamaran sea trials strain gauge data using finite element methods. Det Norske Veritas (DNV) load cases are applied to a finite element model in order to determine the conversion between local strain values observed during sea trials and prevailing global loads. Comparisons are thus made of global loads determined from strain data collected from sea trials with DNV global load cases. The results show that this method is relatively reliable for the prediction of hull global loads in the absence of slamming. Comparisons have been made for different heading angles. The quasi-static design loads are important during the ship design stage, as they are good proxies in wavelengths comparable to the hull length for rationally determined loads obtained from a first-principles dynamic analysis. The broad aims here are to demonstrate the use of strain sensor data obtained during sea trials for determination of global sea loads, to reconcile the loads thus determined with DNV load cases and thereby to improve the accuracy of the predicted loads used in design to increase the structural efficiency of vessel design.

Delamination in the scoring and folding of paperboard

TAPPI Journal ◽  
2012 ◽  
Vol 11 (1) ◽  
pp. 61-66 ◽  
Author(s):  
DOEUNG D. CHOI ◽  
SERGIY A. LAVRYKOV ◽  
BANDARU V. RAMARAO
Keyword(s):  
Finite Element ◽  
Plane Deformation ◽  
Strain Analysis ◽  
Local Strain ◽  
Uniaxial Stress ◽  
Material Model ◽  
Element Model ◽  
Plastic Behavior ◽  
Stress Strain ◽  
Strain Fields

Delamination between layers occurs during the creasing and subsequent folding of paperboard. Delamination is necessary to provide some stiffness properties, but excessive or uncontrolled delamination can weaken the fold, and therefore needs to be controlled. An understanding of the mechanics of delamination is predicated upon the availability of reliable and properly calibrated simulation tools to predict experimental observations. This paper describes a finite element simulation of paper mechanics applied to the scoring and folding of multi-ply carton board. Our goal was to provide an understanding of the mechanics of these operations and the proper models of elastic and plastic behavior of the material that enable us to simulate the deformation and delamination behavior. Our material model accounted for plasticity and sheet anisotropy in the in-plane and z-direction (ZD) dimensions. We used different ZD stress-strain curves during loading and unloading. Material parameters for in-plane deformation were obtained by fitting uniaxial stress-strain data to Ramberg-Osgood plasticity models and the ZD deformation was modeled using a modified power law. Two-dimensional strain fields resulting from loading board typical of a scoring operation were calculated. The strain field was symmetric in the initial stages, but increasing deformation led to asymmetry and heterogeneity. These regions were precursors to delamination and failure. Delamination of the layers occurred in regions of significant shear strain and resulted primarily from the development of large plastic strains. The model predictions were confirmed by experimental observation of the local strain fields using visual microscopy and linear image strain analysis. The finite element model predicted sheet delamination matching the patterns and effects that were observed in experiments.

Numerical evaluation of hydrodynamic characteristics of planing hulls by using a hybrid method

2021 ◽  
pp. 147509022199024
Author(s):  
Emre Kahramanoglu ◽  
Silvia Pennino ◽  
Huseyin Yilmaz
Keyword(s):  
Experimental Data ◽  
Hybrid Method ◽  
Design Stage ◽  
Hydrodynamic Characteristics ◽  
Calm Water ◽  
Preliminary Design Stage ◽  
Reduction Function ◽  
Hull Forms ◽  
Good Agreement

The hydrodynamic characteristics of the planing hulls in particular at the planing regime are completely different from the conventional hull forms and the determination of these characteristics is more complicated. In the present study, calm water hydrodynamic characteristics of planing hulls are investigated using a hybrid method. The hybrid method combines the dynamic trim and sinkage from the Zarnick approach with the Savitsky method in order to calculate the total resistance of the planing hull. Since the obtained dynamic trim and sinkage values by using the original Zarnick approach are not in good agreement with experimental data, an improvement is applied to the hybrid method using a reduction function proposed by Garme. The numerical results obtained by the hybrid and improved hybrid method are compared with each other and available experimental data. The results indicate that the improved hybrid method gives better results compared to the hybrid method, especially for the dynamic trim and resistance. Although the results have some discrepancies with experimental data in terms of resistance, trim and sinkage, the improved hybrid method becomes appealing particularly for the preliminary design stage of the planing hulls.

scholarly journals Stiffness Estimation and Equivalence of Boundary Conditions in FEM Models

2021 ◽  
Vol 11 (4) ◽  
pp. 1482
Author(s):  
Róbert Huňady ◽  
Pavol Lengvarský ◽  
Peter Pavelka ◽  
Adam Kaľavský ◽  
Jakub Mlotek
Keyword(s):  
Boundary Condition ◽  
Finite Element ◽  
Boundary Conditions ◽  
Model Updating ◽  
Element Model ◽  
Computational Time ◽  
Stiffness Coefficients ◽  
First Case ◽  
Numerical Approaches

The paper deals with methods of equivalence of boundary conditions in finite element models that are based on finite element model updating technique. The proposed methods are based on the determination of the stiffness parameters in the section plate or region, where the boundary condition or the removed part of the model is replaced by the bushing connector. Two methods for determining its elastic properties are described. In the first case, the stiffness coefficients are determined by a series of static finite element analyses that are used to obtain the response of the removed part to the six basic types of loads. The second method is a combination of experimental and numerical approaches. The natural frequencies obtained by the measurement are used in finite element (FE) optimization, in which the response of the model is tuned by changing the stiffness coefficients of the bushing. Both methods provide a good estimate of the stiffness at the region where the model is replaced by an equivalent boundary condition. This increases the accuracy of the numerical model and also saves computational time and capacity due to element reduction.

Optimization Design of Pressure Shell in Underwater Vehicle Based on Response Surface Model

2009 ◽  
Vol 419-420 ◽  
pp. 89-92
Author(s):  
Zhuo Yi Yang ◽  
Yong Jie Pang ◽  
Zai Bai Qin
Keyword(s):  
Finite Element ◽  
Response Surface ◽  
Optimization Design ◽  
Engineering Application ◽  
Element Model ◽  
Response Surface Model ◽  
Design Stage ◽  
Surface Model ◽  
Design Variables ◽  
Structure Strength

Cylinder shell stiffened by rings is used commonly in submersibles, and structure strength should be verified in the initial design stage considering the thickness of the shell, the number of rings, the shape of ring section and so on. Based on the statistical techniques, a strategy for optimization design of pressure hull is proposed in this paper. Its central idea is that: firstly the design variables are chosen by referring criterion for structure strength, then the samples for analysis are created in the design space; secondly finite element models corresponding to the samples are built and analyzed; thirdly the approximations of these analysis are constructed using these samples and responses obtained by finite element model; finally optimization design result is obtained using response surface model. The result shows that this method that can improve the efficiency and achieve optimal intention has valuable reference information for engineering application.

Use of DNVGL-RP-C203 for Determining the Fatigue Capacity of Connectors

2021 ◽  
Author(s):  
Anthony Muff ◽  
Anders Wormsen ◽  
Torfinn Hørte ◽  
Arne Fjeldstad ◽  
Per Osen ◽  
...  
Keyword(s):  
Finite Element ◽  
Fatigue Testing ◽  
Experimental Testing ◽  
High Strength ◽  
Element Model ◽  
Fatigue Analysis ◽  
Full Scale ◽  
The Finite Element Model

Abstract Guidance for determining a S-N based fatigue capacity (safe life design) for preloaded connectors is included in Section 5.4 of the 2019 edition of DNVGL-RP-C203 (C203-2019). This section includes guidance on the finite element model representation, finite element based fatigue analysis and determination of the connector design fatigue capacity by use of one of the following methods: Method 1 by FEA based fatigue analysis, Method 2 by FEA based fatigue analysis and experimental testing and Method 3 by full-scale connector fatigue testing. The FEA based fatigue analysis makes use of Appendix D.2 in C203-2019 (“S-N curves for high strength steel applications for subsea”). Practical use of Section 5.4 is illustrated with a case study of a fatigue tested wellhead profile connector segment test. Further developments of Section 5.4 of C203-2019 are proposed. This included acceptance criteria for use of a segment test to validate the FEA based fatigue analysis of a full-scale preloaded connector.

Dynamic Analysis of a Turbocharger Centrifugal Compressor Impeller

1991 ◽  
Author(s):  
V. Ramamurti ◽  
D. A. Subramani ◽  
K. Sridhara
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Centrifugal Compressor ◽  
Element Model ◽  
Simplified Model ◽  
Cyclic Symmetry ◽  
Compressor Impeller ◽  
Cyclic Symmetric ◽  
The Finite Element Model

Abstract Stress analysis and determination of eigen pairs of a typical turbocharger compressor impeller have been carried out using the concept of cyclic symmetry. A simplified model treating the blade and the hub as isolated elements has also been attempted. The limitations of the simplified model have been brought out. The results of the finite element model using the cyclic symmetric approach have been discussed.

Research on the Effects of Welding Sequence on Welding Residual Stress of High-Speed Train Based on SYSWELD

2011 ◽  
Vol 399-401 ◽  
pp. 1806-1811
Author(s):  
Yong Hong Chen ◽  
Peng Chen ◽  
Ai Qin Tian
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
High Speed ◽  
Element Model ◽  
Welding Residual Stress ◽  
High Speed Train ◽  
Distribution Law ◽  
Element Analysis ◽  
Welding Sequence ◽  
Maximum Residual Stress

The finite element model of the roof of aluminum high-speed train was established, double ellipsoid heat source was employed, and heat elastic-plastic theory was used to simulate welding residual stress of the component under different welding sequence based on the finite element analysis software SYSWELD. The distribution law of welding residual stress was obtained. And the effects of the welding sequence on the value and distribution of residual stress was analyzed. The numerical results showed that the simulation data agree well with experimental test data. The maximum residual stress appears in the weld seam and nearby. The residual stress value decreases far away from the welding center. Welding sequence has a significant impact on the final welding residual stress when welding the roof of aluminum body. The side whose residual stress needs to be controlled should be welded first.

scholarly journals Effect of spatial distribution of fibers on elastic properties of unidirectional carbon/carbon composites

2021 ◽  
Vol 309 ◽  
pp. 01214
Author(s):  
M.V.N Mohan ◽  
Ramesh Bhagat Atul ◽  
Vijay Kumar Dwivedi
Keyword(s):  
Finite Element ◽  
Spatial Distribution ◽  
Elastic Properties ◽  
Element Model ◽  
Experimental Methods ◽  
Design Stage ◽  
Carbon Composites ◽  
Numerical Predictions ◽  
Numerical Finite Element ◽  
Very High

Carbon/Carbon composites finds its applications in several high temperature applications in the field of Space, Aviation etc. Designing of components or sub systems with carbon/carbon composites is a challenging task. It requires prediction of elastic properties with a very high accuracy. The prediction can be normally done by analytical, numerical or experimental methods. At the design stage the designers resort to numerical predictions as the experimental methods are not feasible during design stage. Analytical methods are complex and difficult to implement. The designers use numerical methods for prediction of elastic properties using Finite Element Modeling (FEM). The spatial distribution of fibers in matrix has an effect on results of prediction of elastic constants. The generation of random spatial distribution of fibers in representative volume element (RVE) challenging. The present work is aimed at study of effect of spatial distribution of fiber in numerical prediction of elastic properties of unidirectional carbon/carbon composites. MATLAB algorithm is used to generate the spatial distribution of fibers in unidirectional carbon/carbon composites. The RVE elements with various random fiber distributions are modeled using numerical Finite element Model using ABAQUS with EasyPBC plugin. The predicted elastic properties have shown significant variation to uniformly distributed fibers.

Sign in / Sign up

Export Citation Format

Share Document