scholarly journals COMPARATIVE CONCENTRATION MEASUREMENTS OF DUST PRODUCED BY WOOD PROCESSING MACHINES

2015 ◽  
Vol 5 (2) ◽  
Author(s):  
Aca Bozilov ◽  
Nenad Zivkovic ◽  
Dusica Pesic ◽  
Nikola Misic ◽  
Bojan Bijelic

Industrial activities have to comply with protective measures. For this reason, it is essential to know the maximum allowable concentration of chemical hazards (gas, steam and dust) which can occur in the workplace. In wood industry, a large amount of wood dust is produced during the mechanical wood processing. Unless adequate measures for its removal are undertaken, there may be potential hazards for the workers’ health. The research has been carried out for purpose of determining the level of dust emission in different machines in wood processing workshops with no de-dusting system included, by measuring concentrations of wood dust produced during the processing of wooden material. Key words: wood processing, wood dust, concentration measuring

2021 ◽  
Vol 9 (E) ◽  
pp. 317-323
Author(s):  
Eko Prasetyo ◽  
Anies Anies ◽  
Nyoman Suci Widyastiti ◽  
Suhartono Suhartono

AIM: This study is a preliminary study to analyze the etiology and pathophysiology of exposure to wood dust and diisocyanates in the wood processing industry in Jepara, Central Java, Indonesia. This study also provides a diagnostic evaluation of occupational asthma (OA) for ongoing exposure. METHODS: The research method was carried out with a systematic review of various previous findings and with a preliminary study of workers in the processing industry in Jepara, Indonesia. RESULTS: The results show that from a sample of 32 respondents who have been carried out in a wood processing factory in Jepara, it shows that the suspect OA in sanding workers by hand is 75%, with the distribution of signs and symptoms: Chest tightness and pain (90%); cough (53%); shortness of breath (50%); and wheezing (2%). From the signs and symptoms felt, workers felt a continuous increase (progressivity) of OA by 75%. CONCLUSION: Theoretically, this preliminary study is useful to provide information about exposure to wood dust and diisocyanates as a risk factor for OA, especially among workers in the wood industry.


2021 ◽  
Vol 8 (E) ◽  
pp. 317-323
Author(s):  
Eko Prasetyo ◽  
Anies Anies ◽  
Nyoman Suci Widyastiti ◽  
Suhartono Suhartono

AIM: This study is a preliminary study to analyze the etiology and pathophysiology of exposure to wood dust and diisocyanates in the wood processing industry in Jepara, Central Java, Indonesia. This study also provides a diagnostic evaluation of occupational asthma (OA) for ongoing exposure. METHODS: The research method was carried out with a systematic review of various previous findings and with a preliminary study of workers in the processing industry in Jepara, Indonesia. RESULTS: The results show that from a sample of 32 respondents who have been carried out in a wood processing factory in Jepara, it shows that the suspect OA in sanding workers by hand is 75%, with the distribution of signs and symptoms: Chest tightness and pain (90%); cough (53%); shortness of breath (50%); and wheezing (2%). From the signs and symptoms felt, workers felt a continuous increase (progressivity) of OA by 75%. CONCLUSION: Theoretically, this preliminary study is useful to provide information about exposure to wood dust and diisocyanates as a risk factor for OA, especially among workers in the wood industry.


2010 ◽  
Vol 142 ◽  
pp. 134-138
Author(s):  
Han Dong Zhou ◽  
Zhen Ning Liu ◽  
Xiao Bao Lei

In order to design an ESP (electrostatic precipitator) used for the domain of wood processing, electrical resistively of Wood dust should be understand clearly. The ESP could be applied to the dust of which the specific resistance was 104~1011Ω·cm. Dust specific resistance was related with temperature, humidity, the ingredients of dust and so on. Therefore it must be firstly that the specific resistance of wood dust was researched to decide whether the electrostatic dust separator was applied in wood industry.


Forests ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 1039
Author(s):  
Richard Kminiak ◽  
Martin Kučerka ◽  
Lubos Kristak ◽  
Roman Reh ◽  
Petar Antov ◽  
...  

The aim of this paper was to determine the particle size composition of wood dust emission from CNC milling of natural wood and medium-density fiberboard (MDF) and evaluate the associated occupational exposure risks. The paper is focused on some of the most commonly used materials in the woodworking and furniture industry, i.e., solid wood (beech, oak, and spruce) and composite materials (MDF panels). In addition to the influence of the machined material, the effect of the technical-technological parameters, namely, feed speed and depth of cut on the particle size distribution, was also investigated. The selected values of the technical-technological parameters used in this study followed the common work practice in small wood processing companies. The particle size distribution was evaluated by using sieve analysis of samples from the total mass of collected wood dust. The results demonstrated that machining of natural wood is characterized mostly by the formation of coarse dust fractions (2 mm–1 mm sieves), whilst the processing of MDF was associated with generation of fine dust fractions with a size below 100 μm. The results obtained can be used for optimizing the technological programs of CNC milling machines, thus, reducing the occupational exposure to harmful wood dust emissions in the wood-processing industry.


2017 ◽  
Vol 17 (3) ◽  
pp. 2401-2421 ◽  
Author(s):  
Siyu Chen ◽  
Jianping Huang ◽  
Litai Kang ◽  
Hao Wang ◽  
Xiaojun Ma ◽  
...  

Abstract. The Weather Research and Forecasting Model with chemistry (WRF-Chem model) was used to investigate a typical dust storm event that occurred from 18 to 23 March 2010 and swept across almost all of China, Japan, and Korea. The spatial and temporal variations in dust aerosols and the meteorological conditions over East Asia were well reproduced by the WRF-Chem model. The simulation results were used to further investigate the details of processes related to dust emission, long-range transport, and radiative effects of dust aerosols over the Taklimakan Desert (TD) and Gobi Desert (GD). The results indicated that weather conditions, topography, and surface types in dust source regions may influence dust emission, uplift height, and transport at the regional scale. The GD was located in the warm zone in advance of the cold front in this case. Rapidly warming surface temperatures and cold air advection at high levels caused strong instability in the atmosphere, which strengthened the downward momentum transported from the middle and low troposphere and caused strong surface winds. Moreover, the GD is located in a relatively flat, high-altitude region influenced by the confluence of the northern and southern westerly jets. Therefore, the GD dust particles were easily lofted to 4 km and were the primary contributor to the dust concentration over East Asia. In the dust budget analysis, the dust emission flux over the TD was 27.2 ± 4.1 µg m−2 s−1, which was similar to that over the GD (29 ± 3.6 µg m−2 s−1). However, the transport contribution of the TD dust (up to 0.8 ton d−1) to the dust sink was much smaller than that of the GD dust (up to 3.7 ton d−1) because of the complex terrain and the prevailing wind in the TD. Notably, a small amount of the TD dust (PM2.5 dust concentration of approximately 8.7 µg m−3) was lofted to above 5 km and transported over greater distances under the influence of the westerly jets. Moreover, the direct radiative forcing induced by dust was estimated to be −3 and −7 W m−2 at the top of the atmosphere, −8 and −10 W m−2 at the surface, and +5 and +3 W m−2 in the atmosphere over the TD and GD, respectively. This study provides confidence for further understanding the climate effects of the GD dust.


2019 ◽  
Vol 11 (2) ◽  
pp. 99
Author(s):  
Desy Tri Wulansari

Wood dust in the air will bring serious health problems if it is prolonged. Wood Dust has effect for health due to  its effect on , pulmonary function via respiratory system entrance. The aim of this study was to analyze the  association of worker characteristics and dust exposure to pulmonary function status in jumping saw division workers in wood industry Sempu, Banyuwangi. The research was observasional with cross sectional desain. Research data was obtained by giving questionnaire to respondent, measurement of dust level by using HVAS and lung physiology examination using spirometry tool. The sampel in this research was 7 workers in the part of jumping saw and 6 worker in the part of office. Data were analyzed with chi square statistical test  to analyzing the association and statistical t-test to analyzing difference  pulmonary function status between to 2 groups. The result showed that dust level in the exposure groups of jumping saw workers was 19,90 mg/m3 and non-exposure group  (office) was 0,089 mg/m3, suitable with Permenakertrans No. 13/MEN/X/2011 is 5 mg/m3. Results of lung function measurement showed that normal 15,38% and impairment 84,62%. It is concluded that no associoation between age, length of employment, smoking habit, respiratory ptotective equipment usage habit, respiratory diseases history and  dust exposure to pulmonary function status, except association between nutrion status with pulmonary function status. The company should monitor the levels of wood dust, to ensure that it does not exceed the NAB and regular lung physiological health checks.


2021 ◽  
Vol 4 (1) ◽  
Author(s):  
Jaya Kaushik ◽  
◽  
Sandeep Shankar ◽  
Anargh V ◽  
Renu M ◽  
...  

Objective: To formulate a protocol for safe and effective management of an ophthalmologic practice in a hospital or a clinic during the Covid - 19 pandemic. Methods and analysis: Literature was reviewed regarding Covid-19 pandemic and ophthalmology. The following key words were used. Covid-19, telemedicine, challenges, management strategy. Result: An efficient protocol for ophthalmology practice during the Covid-19 pandemic was established which covered various protective measures that are essential and vital in the Covid-19 pandemic. Conclusion: An evidence-based protocol was formulated which may be modified in future as per the latest developments and trends in the ongoing pandemic.


2020 ◽  
Vol 110 (01-02) ◽  
pp. 64-69
Author(s):  
Hans-Christian Möhring ◽  
Thomas Stehle ◽  
Matthias Schneider

Im Beitrag werden zwei Verfahren zur Ermittlung der Staubemission an Werkzeugmaschinen vorgestellt. Es werden das „gravimetrische Verfahren“ und die „Ermittlung des Erfassungsgrades“ beschrieben und gegenübergestellt. Das gravimetrische Verfahren zur Ermittlung des luftgetragenen Holzstaubs ist Stand der Technik zur Beurteilung der Staubemission von Holzbearbeitungsmaschinen. Dieses aufwendige Messverfahren mit Staub-Probenentnahmegeräten erlaubt eine Aussage über den Emissionsgrad der untersuchten Maschine. Dagegen quantifiziert die Ermittlung des Erfassungsgrades einer Bearbeitungsmaschine die Effektivität des Absaugsystems bei der Erfassung von Spänen und Stäuben. Ein Vergleich von Gravimetrie und Erfassungsgrad soll eine detaillierte Aussage zu den emittierten Späne- und Staubmengen von Bearbeitungsmaschinen für die Holz- und Holzwerkstoffbearbeitung liefern. Beim Messverfahren Ermittlung des Erfassungsgrades wird davon ausgegangen, dass Späne- und Staubfraktionen ähnlich gut erfasst werden können. Die genaue Zusammensetzung der erfassten und nichterfassten Materialanteile sowie der Partikelgrößen sind derzeit noch Gegenstand der Untersuchungen. Unbenommen davon müssen im Betrieb die nichterfassten Anteile aufwendig vom Benutzer in einem nachgelagerten Prozessschritt aufgesaugt werden. Es wird ausdrücklich darauf hingewiesen, dass die Untersuchung des Emissions- oder Erfassungsgrades einer Maschine nur eine qualitative Aussage zur Staubbelastung in der Umgebung einer Maschine erlaubt. Die Einwirkung beziehungsweise Exposition von Mitarbeitern hängt von Umgebungsbedingungen wie zum Beispiel Raumgröße, Luftwechsel, Sauberkeit, Leistung der Absauganlage, Beeinflussung durch Nachbararbeitsplätze (Bystanderexposition) und nicht zuletzt vom Handling des Bedieners ab. Diese Faktoren werden im Allgemeinen nicht von der Maschine beziehungsweise dem Maschinenhersteller beeinflusst.   This paper presents two methods for determining the dust emission of machine tools. The gravimetric method and the determination of the degree of collection efficiency are described and compared. compared. The gravimetric method for establishing airborne wood dust is state of the art for assessing the dust emission of woodworking machines. This complicated measuring method with dust sampling devices makes it possible to assess the emissivity of the examined machine. In contrast, establishing the degree of collection efficiency for a machining centre quantifies how efficient the suction system collects chips and dust. By comparing gravimetric analyses and the degree of collection efficiency, it is possible to provide a detailed assessment about the amount of chips and dust emitted by machining centres in the machining of wood and wood-based products. The measuring method for establishing the degree of collection efficiency assumes that chip and dust fractions can be collected similarly well. The exact composition of the collected and uncollected material fractions as well as the particle sizes still have to be examined yet. Irrespective of that, the uncollected particles have to be removed during operation in a subsequent, complicated process step by the user. It has to be emphasized particularly that by analysing the emissivity or the degree of collection efficiency of a machine it is only possible to qualitatively assess the dust exposure in the surroundings of the machine. The influence or exposure of workers depends on environmental conditions, such as e.g. room size, air change, cleanness, the efficiency of the suction system, the influence by adjacent machines (bystander exposure) and last but not least the handling of the operator. In general, these factors are not influenced by the machine or rather the machine manufacturer.


Author(s):  
Bartosz Pałubicki ◽  
Luďka Hlásková ◽  
Tomasz Rogoziński

Air pollution by wood dust in furniture production sites is an important hygiene issue. The dust is created by all types of wood and wood-based material machining, and its concentration in the working zone surrounding the machining stand depends on the effectiveness of the dust exhaust system. In present research, three setups of the dust extraction system for a conventional table sawing machine are considered while machining particleboards. The results showed a high impact of the exhaust system connection setup on the dust concentration in the air surrounding the sawing machine work stand. The use of both main and auxiliary sawdust extraction connectors together ensured the highest clearness of the air, with only 0.5 mg/m3 of dust concentration. Closing the upper hood leads to a concentration five times higher, while disconnecting it results in a ten times higher dust content. The finest dust particles (<1 µm), however, are the most numerous in the case of closing the hood.


Sign in / Sign up

Export Citation Format

Share Document