Fibrillation Characteristics of Cellulose Nanofibrils with Water Retention Value Method

Author(s):  
Woo-Yong Song ◽  
Su Bin Jeong ◽  
So Young Juhn ◽  
Soo-Jeong Shin
2020 ◽  
Vol 35 (4) ◽  
pp. 670-684
Author(s):  
Iara Fontes Demuner ◽  
Jorge Luiz Colodette ◽  
Fernando José Borges Gomes ◽  
Rubens Chaves de Oliveira

AbstractNanocelluloses produced from wood pulp are widely studied for various economic applications. Most studies of cellulose nanofibrils (CNF) use lignin-free fibres obtained from bleached pulps; however, unbleached fibres with residual lignin may also be used to obtain lignocelluloses nanofibrils (LCNF). Research on lignocellulose nanofibrils is a recent subject in the field; thus, the aim of the present study was to determine the ultrastructure of lignocellulose nanofibrils compared to cellulose nanofibrils produced from the same raw material. Understanding of nanoparticle properties is of great relevance for their various applications; therefore, complete characterisation of the chemical, physical, and morphological structures of LCNF and CNF produced from pine and eucalyptus woods was performed. Unbleached cellulosic fibres are a viable alternative for LCNF production, which has properties comparable to that of traditional CNF production that uses lignin-free fibres. LCNF from pine and eucalyptus were obtained with 4.0 % and 1.8 % residual lignin, respectively. The nanofibrils had high thermal stability because LCNF had a higher maximum degradation temperature. Due to the low interaction of lignin with water, LCNF had a lower water retention value than CNF.


TAPPI Journal ◽  
2020 ◽  
Vol 19 (5) ◽  
pp. 239-246
Author(s):  
XIAONING SHEN ◽  
BO LI ◽  
WENXUAN MO ◽  
XIN-SHENG CHAI

This paper presents data on the effects of operational parameters (number of revolutions, linear pressure, and gap) of the PFI refiner on the swellability of recycled fiber, which was characterized by water retention value (WRV). The results showed that the increase of recycled fiber’s WRV was proportional to the number of revolutions and the linear pressure, but inversely proportional to the gap. The mathematical relation between these parameters and the fiber WRV could be described by an empirical model for gaps greater than 0.1 mm. Scanning electron microscopic images of fiber morphology showed that the basic framework of fibers could be maintained with the gap greater than 0.1 mm, but was destroyed with smaller gaps. This model provides a technical reference for quantitative control of refining treatment and an effective method for improving recycled fiber quality.


Holzforschung ◽  
2010 ◽  
Vol 64 (2) ◽  
Author(s):  
Iiro Pulkkinen ◽  
Juha Fiskari ◽  
Ville Alopaeus

Abstract The activation parameter developed is based on the fiber wall thickness distribution, fiber curl distribution, and water retention value of the unrefined fibers. The mechanical properties of paper that contain chemical pulp depend, among other things, on the free fiber segment activation between fiber-fiber crossings that is created during drying. Experimental data revealed that the degree of fiber swelling is responsible together with the fiber shape factor (curl) and fiber wall thickness for the extent of fiber network activation. The amount of bonding between fibers also affects fiber segment activation. Based on the experimental data, it was deduced that interfiber bonding ability of fibers, characterized as the water retention value, was mainly responsible for the development of handsheet density. Tensile index development was more affected by the morphology of fibers, which was the main determinant for high activation potential of fibers. Factor analysis was used to identify the main causes of variation for a refining data set of 20 Eucalyptus grandis samples. Three independent descriptors were found to be responsible for the majority of the variation: the bonding and activation factor, the factor of microcompressions, and the factor of fiber wall thickness and fiber curl. The activation parameter developed in this study can be used to determine the effect of fiber segment activation and inter-fiber bonding on the inplane mechanical properties of paper.


2018 ◽  
Vol 33 (4) ◽  
pp. 651-660 ◽  
Author(s):  
Yingju Miao ◽  
Yunfei Zhi ◽  
Heng Zhang ◽  
Ying Chen ◽  
Shaoyun Shan ◽  
...  

Abstract Hydrogen bonding among fiber microfibrils is the primary cause of fiber hornification, wherein NaOH/urea aqueous solution precooled to −13 °C can disassemble inter- and intramolecular hydrogen bonds. Whether hornified fibers treated with this process can significantly improve fiber swelling ability and physical properties of the resulting paper sheets remains a problem. In this investigation, the 6th cycle fiber was pretreated with this procedure, and the water retention value of the fiber before and after treatment and the physical properties of the resulting paper sheets were studied. The results indicate that the lignin decline, complete swelling of flat fiber, filling of cellulose film between the interfiber network, and decreasing crystalline region all contribute to the increase in water retention value. The water retention value of repaired fiber is equivalent to that of virgin pulp, and hornification reverses by 89 %. In addition, the cellulose film filling among the fiber network constructs a similar reinforced concrete structure, which causes the tear, burst, and tensile index of the resulting paper sheets to increase by 145 %, 98 %, and 43 %, respectively.


1970 ◽  
Vol 17 (2) ◽  
pp. 150-154
Author(s):  
Marianna LAKA ◽  
Svetlana CHERNYAVSKAYA ◽  
Galia SHULGA ◽  
Viktor SHAPOVALOV ◽  
Andrej VALENKOV ◽  
...  

The composites, containing recycled polypropylene and fillers, obtained from different lignocellulosics by the thermocatalytic destruction method, were investigated. Birch sawdust, newsprint wastes, cotton residues and wood bleached sulphate pulp were used as raw materials for obtaining fillers. The indices of mechanical properties (tensile strength, modulus of elasticity, deformation at break, shear modulus, toughness, twisting moment) of the composites' samples were determined. It has been found that the obtained composites have relatively good mechanical properties. Better results were obtained, using fillers from sawdust and wood pulp. After treating the fillers with rapeseed oil, their water vapour sorption and water retention value (WRV) decreased. In this case, the strength of the composites was higher.http://dx.doi.org/10.5755/j01.ms.17.2.484


2013 ◽  
Vol 781-784 ◽  
pp. 2645-2649
Author(s):  
Yan Na Yin ◽  
Quan Xiao Liu ◽  
Yu Bin Lyu

Effects of mercerizing treatment on water-retention value of straw pulp fibers were discussed and the mercerizing treatment conditions were optimized. The best conditions of mercerizing treatment is NaOH concentration of 4mol/L, temperature of 40°C and processing time of 60min. SEM showed that the fiber cell wall swelling increase after mercerization.


2012 ◽  
Vol 518-523 ◽  
pp. 604-607
Author(s):  
Jie He

In this paper, two groups of Dendrocalamus giganteus Munro pulp were obtained from conventional kraft pulping (the maximum pulping temperature was 165°C) and low-temperature kraft pulping (the maximum pulping temperature was only 135°C) under the premise of kappa number of about 17, and the viscosity of them were 1240 mL•g-1 and 1426 mL•g-1 respectively. Then the handsheets was treated with dry heat aging and the simulation of pulp recycling was investigated. In addition, the relationship between the pulp viscosity and recycling times of pulp were studied. The results showed that the viscosity and water retention value of two groups of pulp decreased with increasing of recycling times. However, the recycling characteristic of the pulp with high viscosity from low-temperature kraft cooking was better.


Cellulose ◽  
2019 ◽  
Vol 26 (18) ◽  
pp. 9877-9888
Author(s):  
Sara Ceccherini ◽  
Thad Maloney

Abstract Recent years have witnessed an increasing interest in man-made cellulosic fibers, whose production generally requires cellulose dissolution and regeneration. Cellulosic fibers are difficult to dissolve. Thus, the recalcitrance of wood pulp can be an estimate of its reactivity. Pulp reactivity is usually assessed via complex and time-consuming laboratory simulations of the viscose process. This study proposes a faster and more convenient approach. The dissolution-based torque reactivity (DTR) test measures the evolution of the rheological properties of a pulp suspension under dissolution in cupriethylenediamine. Reactivity is quantified in terms of initial dissolution rates (IDR) and dissolution times (DT). This study describes the measurement protocol for the DTR test and its application to some commercial pulps and a series of pulps hornified to different extents. The IDR and DT values were compared with other pulp features, including degree of polymerization, molecular weight distribution, specific surface area and water retention value. The DTR test proved to be reasonably precise and fast to carry out. Graphic abstract


Sign in / Sign up

Export Citation Format

Share Document