Photovoltaic Characteristics of GaSe/MoSe2 Heterojunction Devices

The two-dimensional materials have the thickness of an atomic layer level and are expected as alternative materials for future electronics and optoelectronics due to their specific properties. Especially recently, transition metal monochalcogenides and dichalcogenides have attracted attention. Since these materials have a band gap unlike graphene and exhibit a semiconductor property even in a single layer, application to a new flexible optoelectronics is expected. In this study, the photovoltaic characteristics of a GaSe/MoSe2 heterojunction device using two-dimensional semiconductors, p-type GaSe and n-type MoSe2, were investigated. The heterojunction device was prepared by transferring GaSe and MoSe2 onto the substrate which the titanium electrodes were fabricated through a mechanical peeling method. The current–voltage characteristics of the GaSe/MoSe2 heterojunction device were measured in a dark condition and under light irradiation using a solar simulator. The irradiation light intensity was changed from 0.5 to 1.5 sun. It was found that when the illuminance was increased in this illuminance range, both the short-circuit current and the open-circuit voltage increased. The open-circuit voltage and the energy conversion efficiency were 0.41 V and 0.46% under 1.5 sun condition, respectively.

Temperature-dependent device properties of γ-CuI and β-Ga2O3 heterojunctions

Temperature-dependent studies of Ga2O3-based heterojunction devices are important in understanding its carrier transport mechanism, junction barrier potential, and stability at higher temperatures. In this study, we investigated the temperature-dependent device characteristics of the p-type γ-copper iodide (γ-CuI)/n-type β-gallium oxide (β‐Ga2O3) heterojunctions, thereby revealing their interface properties. The fabricated γ-CuI/β-Ga2O3 heterojunction showed excellent diode characteristics with a high rectification ratio and low reverse saturation current at 298 K in the presence of a large barrier height (0.632 eV). The temperature-dependent device characteristics were studied in the temperature range 273–473 K to investigate the heterojunction interface. With an increase in temperature, a gradual decrease in the ideality factor and an increase in the barrier height were observed, indicating barrier inhomogeneity at the heterojunction interface. Furthermore, the current–voltage measurement showed electrical hysteresis for the reverse saturation current, although it was not observed for the forward bias current. The presence of electrical hysteresis for the reverse saturation current and of the barrier inhomogeneity in the temperature-dependent characteristics indicates the presence of some level of interface states for the γ-CuI/β‐Ga2O3 heterojunction device. Thus, our study showed that the electrical hysteresis can be correlated with temperature-dependent electrical characteristics of the β‐Ga2O3-based heterojunction device, which signifies the presence of surface defects and interface states. Article Highlights We revealed the interface properties of p-type γ-copper iodide (γ-CuI) and n-type β-gallium oxide (β-Ga2O3) heterojunction. The developed heterostructure showed a large barrier height (0.632 eV) at the interface, which is stable at a temperature as high as 473 K. We confirmed the current transport mechanism at the interface of the heterojunction by analyzing the temperature dependent current–voltage characterization. Graphic abstract

Effect of Multilayer Configuration on Spectral Response of Thin Film TiO2/NiO Heterojunction Photodetector

In this work, a multilayer design for the TiO2/NiO heterojunction device is proposed. In this design, layers of TiO2 nanostructures are consecutively deposited on layers of NiO nanostructures deposited on ITO substrates. This design was compared to the conventional design of thin film TiO2/NiO heterojunction device by measuring the spectral response of both designs in the spectral range of 200–1200 nm. The proposed design showed increased response intensity by 14%, narrowing spectral width by 23% and single peak of response at 440nm.

Innovative Implementation of an Alternative Tetrathiafulvene Derivative for Flexible Indium Phthalocyanine Chloride-Based Solar Cells

Herein, we present the photovoltaic properties of an indium phthalocyanine chloride (InClPc)-based flexible planar heterojunction device, introducing the tetrathiafulvene derivative 4,4′-Dimethyl-5,5′-diphenyltetrathiafulvalene (DMDP-TTF) as the electron donor layer. UV-vis spectroscopy is widely used to characterize the electronic behavior of the InClPc/DMDP-TTF active layer. The interactions between the DMDP-TTF and phthalocyanine are predominantly intermolecular and the result of the aggregation of InClPc. Tauc bands were obtained at 1.41 and 2.8 eV; these energy peaks can result in a charge transfer ascribed to the transition from the DMDP-TTF to π-orbitals that are associated with the phthalocyanine ring or even with the same indium metal center. Conductive carbon (CC) was used for the cathode. Finally, an indium tin oxide (ITO)/InClPc/DMDP-TTF/CC device was fabricated by high-vacuum thermal evaporation onto a flexible substrate and the photovoltaic properties were evaluated. A diode type I-V curve behavior was observed with a photovoltaic response under illumination. A generated photocurrent of 2.25 × 10−2 A/cm2 was measured. A conductivity reduction with the incident photon energy from 1.61 × 10−7 S/cm to 1.43 × 10−7 S/cm is observed. The diode resistance presents two different behaviors with the applied voltage. A VTFL of 5.39 V, trap concentration of 7.74 × 1016 cm−3, and carrier mobility values of ~10−6 cm2/V s were calculated, showing improved characteristics via the innovative implementation of an alternative TTF-derivative, indicating that the DMDP-TTF has a strong interaction at the junction where free available states are increased, thus inducing higher mobilities due to the large number of π-orbitals, which indicates the feasibility of its use in solar cells technology.

Broadband Detection Based on 2D Bi2Se3/ZnO Nanowire Heterojunction

The investigation of photodetectors with broadband response and high responsivity is essential. Zinc Oxide (ZnO) nanowire has the potential of application in photodetectors, owing to the great optoelectrical property and good stability in the atmosphere. However, due to a large number of nonradiative centers at interface and the capture of surface state electrons, the photocurrent of ZnO based photodetectors is still low. In this work, 2D Bi2Se3/ZnO NWAs heterojunction with type-I band alignment is established. This heterojunction device shows not only an enhanced photoresponsivity of 0.15 A/W at 377 nm three times of the bare ZnO nanowire (0.046 A/W), but also a broadband photoresponse from UV to near infrared region has been achieved. These results indicate that the Bi2Se3/ZnO NWAs type-I heterojunction is an ideal photodetector in broadband detection.