Solid‐State Reactions Between Copper and Solder

2021 ◽  
pp. 105-125
Author(s):  
L. A. Bendersky ◽  
W. J. Boettinger

Rapid solidification produces a wide variety of sub-micron scale microstructure. Generally, the microstructure depends on the imposed melt undercooling and heat extraction rate. The microstructure can vary strongly not only due to processing parameters changes but also during the process itself, as a result of recalescence. Hence, careful examination of different locations in rapidly solidified products should be performed. Additionally, post-solidification solid-state reactions can alter the microstructure.The objective of the present work is to demonstrate the strong microstructural changes in different regions of melt-spun ribbon for three different alloys. The locations of the analyzed structures were near the wheel side (W) and near the center (C) of the ribbons. The TEM specimens were prepared by selective electropolishing or ion milling.


Author(s):  
S.R. Summerfelt ◽  
C.B. Carter

The wustite-spinel interface can be viewed as a model interface because the wustite and spinel can share a common f.c.c. oxygen sublattice such that only the cations distribution changes on crossing the interface. In this study, the interface has been formed by a solid state reaction involving either external or internal oxidation. In systems with very small lattice misfit, very large particles (>lμm) with coherent interfaces have been observed. Previously, the wustite-spinel interface had been observed to facet on {111} planes for MgFe2C4 and along {100} planes for MgAl2C4 and MgCr2O4, the spinel then grows preferentially in the <001> direction. Reasons for these experimental observations have been discussed by Henriksen and Kingery by considering the strain energy. The point-defect chemistry of such solid state reactions has been examined by Schmalzried. Although MgO has been the principal matrix material examined, others such as NiO have also been studied.


Author(s):  
W. A. Chiou ◽  
N. L. Jeon ◽  
Genbao Xu ◽  
M. Meshii

For many years amorphous metallic alloys have been prepared by rapid quenching techniques such as vapor condensation or melt quenching. Recently, solid-state reactions have shown to be an alternative for synthesizing amorphous metallic alloys. While solid-state amorphization by ball milling and high energy particle irradiation have been investigated extensively, the growth of amorphous phase by cold-rolling has been limited. This paper presents a morphological and structural study of amorphization of Cu and Ti foils by rolling.Samples of high purity Cu (99.999%) and Ti (99.99%) foils with a thickness of 0.025 mm were used as starting materials. These thin foils were cut to 5 cm (w) × 10 cm (1), and the surface was cleaned with acetone. A total of twenty alternatively stacked Cu and Ti foils were then rolled. Composite layers following each rolling pass were cleaned with acetone, cut into half and stacked together, and then rolled again.


Author(s):  
P. G. Kotula ◽  
D. D. Erickson ◽  
C. B. Carter

High-resolution field-emission-gun scanning electron microscopy (FESEM) has recently emerged as an extremely powerful method for characterizing the micro- or nanostructure of materials. The development of high efficiency backscattered-electron detectors has increased the resolution attainable with backscattered-electrons to almost that attainable with secondary-electrons. This increased resolution allows backscattered-electron imaging to be utilized to study materials once possible only by TEM. In addition to providing quantitative information, such as critical dimensions, SEM is more statistically representative. That is, the amount of material that can be sampled with SEM for a given measurement is many orders of magnitude greater than that with TEM.In the present work, a Hitachi S-900 FESEM (operating at 5kV) equipped with a high-resolution backscattered electron detector, has been used to study the α-Fe2O3 enhanced or seeded solid-state phase transformations of sol-gel alumina and solid-state reactions in the NiO/α-Al2O3 system. In both cases, a thin-film cross-section approach has been developed to facilitate the investigation. Specifically, the FESEM allows transformed- or reaction-layer thicknesses along interfaces that are millimeters in length to be measured with a resolution of better than 10nm.


Author(s):  
F. Ma ◽  
S. Vivekanand ◽  
K. Barmak ◽  
C. Michaelsen

Solid state reactions in sputter-deposited Nb/Al multilayer thin films have been studied by transmission and analytical electron microscopy (TEM/AEM), differential scanning calorimetry (DSC) and X-ray diffraction (XRD). The Nb/Al multilayer thin films for TEM studies were sputter-deposited on (1102)sapphire substrates. The periodicity of the films is in the range 10-500 nm. The overall composition of the films are 1/3, 2/1, and 3/1 Nb/Al, corresponding to the stoichiometric composition of the three intermetallic phases in this system.Figure 1 is a TEM micrograph of an as-deposited film with periodicity A = dA1 + dNb = 72 nm, where d's are layer thicknesses. The polycrystalline nature of the Al and Nb layers with their columnar grain structure is evident in the figure. Both Nb and Al layers exhibit crystallographic texture, with the electron diffraction pattern for this film showing stronger diffraction spots in the direction normal to the multilayer. The X-ray diffraction patterns of all films are dominated by the Al(l 11) and Nb(l 10) peaks and show a merging of these two peaks with decreasing periodicity.


1990 ◽  
Vol 51 (C4) ◽  
pp. C4-121-C4-130
Author(s):  
U. KÖSTER ◽  
R. PRIES ◽  
G. BEWERNICK ◽  
B. SCHUHMACHER ◽  
M. BLANK-BEWERSDORFF

1997 ◽  
Vol 481 ◽  
Author(s):  
Matthew T. Johnson ◽  
Shelley R. Gilliss ◽  
C. Barry Carter

ABSTRACTThin films of In2O3 and Fe2O3 have been deposited on (001) MgO using pulsed-laser deposition (PLD). These thin-film diffusion couples were then reacted in an applied electric field at elevated temperatures. In this type of solid-state reaction, both the reaction rate and the interfacial stability are affected by the transport properties of the reacting ions. The electric field provides a very large external driving force that influences the diffusion of the cations in the constitutive layers. This induced ionic current causes changes in the reaction rates, interfacial stability and distribution of the phases. Through the use of electron microscopy techniques the reaction kinetics and interface morphology have been investigated in these spinel-forming systems, to gain a better understanding of the influence of an electric field on solid-state reactions.


1997 ◽  
Vol 52 (5) ◽  
pp. 663-668 ◽  
Author(s):  
B. Mertens ◽  
Hk. Müller-Buschbaum

Abstract Single crystals of I RbCd4V3O12 and TlCd4V3O12 II have been prepared by solid state reactions in closed iron tubes. The compounds crystallize closely related to the Johillerite structure in the space group C62h- C2/c with I: a = 13.058(3); b - 13.528(3), c = 7 .0 6 0 (2 )Å , β = 114.88(2)°; II: a = 12.999(6), b = 13.527(7), c = 7.055(3) Å , β = 114.88(4)°, Z = 4. Special features are the loss of Cu2+ in order to gain an additional Cd2+ position. The crystal structure is discussed with respect to related compounds of the Johillerite type.


2000 ◽  
Vol 658 ◽  
Author(s):  
Boris Wedel ◽  
Katsumasa Sugiyama ◽  
Kimio Itagaki ◽  
Hanskarl Müller-Buschbaum

ABSTRACTDuring the past decades the solid state chemistry of tellurium oxides has been enriched by a series of quaternary metallates. Interest attaches not only to the chemical and physical properties of these compounds, but also to their structure, which have been studied by modern methods. The partial similarity of earth alkaline metals and lead in solid state chemistry and their relationships in oxides opens a wide field of investigations. Eight new compounds in the systems Ba-M-Te-O (M= Nb, Ta) and Pb-M-Te-O (M = Mn, Ni, Cu, Zn) were prepared and structurally characterized: Ba2Nb2TeO10, Ba2M6Te2O21 (M = Nb, Ta) and the lead compounds PbMnTeO3, Pb3Ni4.5Te2.5O15, PbCu3TeO7, PbZn4SiTeO10 and the mixed compound PbMn2Ni6Te3O18. The structures of all compounds are based on frameworks of edge and corner sharing oxygen octahedra of the transition metal and the tellurium. Various different channel structures were observed and distinguished. The compounds were prepared by heating from mixtures of the oxides, and the single crystals were grown by flux method or solid state reactions on air. The synthesis conditions were modified to obtained microcrystalline material for purification and structural characterizations, which were carried out using a variety of tools including powder diffraction data and refinements of X-ray data. Relationships between lead transition metal tellurium oxides and the earth alkaline transition metals tellurium oxides are compared.


Sign in / Sign up

Export Citation Format

Share Document