Determining the Quality of Activated Carbon Using L16 Taguchi Method Through Waste Tyre Recycling

Author(s):  
Tirthankar Mukherjee ◽  
Sadhan Kumar Ghosh ◽  
Mehabub Rahaman
2010 ◽  
Vol 443 ◽  
pp. 543-548
Author(s):  
Jian Long Kuo ◽  
Kai Lun Chao ◽  
Chun Cheng Kuo

Because the solder residue was found in the manufacturing process which greatly affected the product quality, the purpose of this paper was to make the product quality improved and to find an optimal solution for process parameters in the flip chip process. The experimental testing was based on SMT manufacturing process. The amount and size of solder left on passive component in the process of manufacturing were considered as the quality traits. Since too many solders left on the passive component side during flux cleaning process, it was possible that the balling would be flowed into the chip, which caused the bump short in the chip and affected the quality of the product. In this paper, orthogonal array by using Taguchi method is adopted as the effective experimental method with the least experimental runs. Also, based on the quality evaluation of signal-to-noise ratio, the ANOVA is used to evaluate the effects of quality target according to the experimental results. The results reveal that the optimization in the process is confirmed. Therefore, this study can effectively improve the solder residue in semiconductor manufacturing process.


Author(s):  
В.А. Гвоздев ◽  
Л.В. Леонов ◽  
О.Н. Рублевская

Качество услуг водоснабжения и водоотведения за первые двадцать лет XXI века вывело на новый уровень развития ГУП «Водоканал Санкт-Петербурга» благодаря внедрению инновационных технологий в системах водоснабжения и водоотведения. Использование технологий, таких как двухступенчатое обеззараживание питьевой воды, дезодорирование полигонов, геотубирование, применение центрифуг «Флоттвег», порошкообразного однокомпонентного флокулянта, порошкообразного активированного угля, внедрение системы измерения осадков, осуществлялись при активном участии Федора Ивановича Лобанова – помощника генерального директора ГУП «Водоканал Санкт-Петербурга» по работе с промышленностью, которому в ноябре 2021 г. исполнилось 80 лет. The quality of water supply and wastewater disposal services over the first twenty years of the 21st century has brought SUE «Vodokanal of St. Petersburg» to a new level of development owing to the introduction of innovative technologies in water supply and wastewater disposal systems. The use of technologies, such as two-stage disinfection of drinking water, odor control of landfills, geotubing, the use of Flottweg centrifuges, powdered one-component flocculant, powdered activated carbon, the introduction of a precipitation measurement system, were carried out with the active participation of Fedor Ivanovich Lobanov, Assistant to the General Director of SUE «Vodokanal of St. Petersburg» on dealing with industries, who turned 80 in November 2021.


2019 ◽  
Vol 210 ◽  
pp. 630-637 ◽  
Author(s):  
Seiko Jose ◽  
Leena Mishra ◽  
Sayandeep Debnath ◽  
Sourav Pal ◽  
Prabhat K. Munda ◽  
...  

2022 ◽  
Author(s):  
Jose Luis Meseguer Valdenebro ◽  
Eusebio José Martínez Conesa ◽  
Antonio Portoles

Abstract The aim of this work is to carry out the design of experiments that determine the influence of the welding parameters using Taguchi’s method on the grain size, HAZ, and the degree of dilution in 6063-T5 alloy. The welding process used is GMAW and the welding parameters are power, welding speed and bevel spacing. The study of the influence of the welding parameters on the measurements made in the welding (which are the size of heat affected zone, the degree of dilution, and the grain size) allows one to determine the quality of the joint . In addition, the welding parameter most influential in minimising the three measurements will be determined.


Author(s):  
Ednei Bruce Da Silva ◽  
Antônio Estanislau Sanches ◽  
David Barbosa de Alencar ◽  
Mike Jordan Braz Izel ◽  
Camily Murrieta Vasconcelos Oliveira Bezerra ◽  
...  

The water treatment processes in which microorganisms act are margin filtration, slow filtration and biological activated carbon (CAB) [2]. For this research, a study of permeable concrete with the addition of 2% activated carbon for light traffic paving was performed. The objective of this research is to identify the feasibility of using this concrete so that filtered water can reach at least the basic sanitation networks, with a better quality to be treated. For this, characterizations of the quality of the concrete component materials were made with a novelty, using the fine aggregate (sand). After the characterizations, the permeable concrete traces with mechanical strength of 30MPa were made. Dosing analyzes followed with molding, curing and rupture of concrete specimens. The results of the arithmetic mean of the axial compression of conventional concrete at 28 days were 34.2 MPa and the concrete with the addition of activated carbon was 32.2 MPa, reaching the expectations of strength. Complementary experiments were performed for the quality of the water filtered by the CP's, the pH, the alkalinity and the chlorine content were analyzed. The pH of the conventional concrete found was 7.6 and the concrete with the addition of activated carbon was between 7.2 and 6.8, which may be the best result found


This research is a study of the turning process by testing with brass material. There are three control factors: spindle of speed, feed rate, and depth of cut respectively. The turning process requires variable control,affect the quality of production productivity and production costplanning an experiment with the Taguchi Method help in theexperiment the analysis of variance, orthogonal array, and signal and noise ratios were considered as an experiment and survey of brass turning characteristics to determine the lowest material removal rate.The results obtained from the experiment were used to repeat the experiment for confirmation. This requires the turning process to be reliable and optimized


Sign in / Sign up

Export Citation Format

Share Document