Analysis of the uniformity of material removal in double-sided grinding based on thermal–mechanical coupling

2022 ◽  
Author(s):  
Qingliang Li ◽  
Shichao Xiu ◽  
Cong Sun ◽  
Yunlong Yao ◽  
Xiangna Kong
Keyword(s):  
Material Removal ◽  
Mechanical Coupling

Research on the Grinding Mechanism Based on the Cutting Simulation

2012 ◽  
Vol 510 ◽  
pp. 395-400
Author(s):  
Hong Xia Zhang ◽  
Wu Yi Chen
Keyword(s):  
Temperature Distribution ◽  
Material Removal ◽  
Operation Research ◽  
Cutting Temperature ◽  
Stress Fields ◽  
Mechanical Coupling ◽  
Abrasive Grain ◽  
Grinding Mechanism ◽  
Cutting Zone ◽  
Simulation Results

Grinding of metals is a complex material removal operation. Research on cutting process of a single abrasive grain is the basis of further understanding of grinding mechanism. In this investigation, the simulation and analysis for the non-uniform thermo-mechanical coupling intense stress fields in cutting zones of a single abrasive with negative rake are conducted by means of the FEM techniques. The cutting forces, the cutting temperature distribution and the strain rate in cutting zone are numerically demonstrated. Grinding mechanics are analyzed from microscopic view according to the simulation results. Research results facilitate a better understanding on the mechanics of grinding.

Effects of Process Parameters on Surface Roughness and MRR in the hard turning of EN 36 steel

2018 ◽  
pp. 102-110
Author(s):  
Amritpal Singh ◽  
Rakesh Kumar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Hard Turning ◽  
Control Parameter ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting

In the present study, Experimental investigation of the effects of various cutting parameters on the response parameters in the hard turning of EN36 steel under the dry cutting condition is done. The input control parameters selected for the present work was the cutting speed, feed and depth of cut. The objective of the present work is to minimize the surface roughness to obtain better surface finish and maximization of material removal rate for better productivity. The design of experiments was done with the help of Taguchi L9 orthogonal array. Analysis of variance (ANOVA) was used to find out the significance of the input parameters on the response parameters. Percentage contribution for each control parameter was calculated using ANOVA with 95 % confidence value. From results, it was observed that feed is the most significant factor for surface roughness and the depth of cut is the most significant control parameter for Material removal rate.

A two degrees of freedom comb capacitive-type accelerometer with low cross-axis sensitivity

2019 ◽  
Vol 13 (3) ◽  
pp. 5334-5346
Author(s):  
M. N. Nguyen ◽  
L. Q. Nguyen ◽  
H. M. Chu ◽  
H. N. Vu
Keyword(s):  
Degrees Of Freedom ◽  
Proof Mass ◽  
Vibration Modes ◽  
Electrode Structure ◽  
Element Analysis ◽  
Mechanical Coupling ◽  
Fully Differential ◽  
Mode Effects ◽  
The Finite Element Analysis ◽  
Cross Axis

In this paper, we report on a SOI-based comb capacitive-type accelerometer that senses acceleration in two lateral directions. The structure of the accelerometer was designed using a proof mass connected by four folded-beam springs, which are compliant to inertial displacement causing by attached acceleration in the two lateral directions. At the same time, the folded-beam springs enabled to suppress cross-talk causing by mechanical coupling from parasitic vibration modes. The differential capacitor sense structure was employed to eliminate common mode effects. The design of gap between comb fingers was also analyzed to find an optimally sensing comb electrode structure. The design of the accelerometer was carried out using the finite element analysis. The fabrication of the device was based on SOI-micromachining. The characteristics of the accelerometer have been investigated by a fully differential capacitive bridge interface using a sub-fF switched-capacitor integrator circuit. The sensitivities of the accelerometer in the two lateral directions were determined to be 6 and 5.5 fF/g, respectively. The cross-axis sensitivities of the accelerometer were less than 5%, which shows that the accelerometer can be used for measuring precisely acceleration in the two lateral directions. The accelerometer operates linearly in the range of investigated acceleration from 0 to 4g. The proposed accelerometer is expected for low-g applications.

Performance Analysis of Trihexyltetradecylphosphonium Chloride Ionic Fluid under MQL Condition in Hard turning

2020 ◽  
Vol 17 (1) ◽  
pp. 7629-7647
Author(s):  
A. Pandey ◽  
R. Kumar ◽  
A. K. Sahoo ◽  
A. Paul ◽  
A. Panda
Keyword(s):  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Coconut Oil ◽  
Chip Morphology ◽  
Weight Fraction ◽  
Cutting Fluid ◽  
Depth Of Cut

The current research presents an overall performance-based analysis of Trihexyltetradecylphosphonium Chloride [[CH3(CH2)5]P(Cl)(CH2)13CH3] ionic fluid mixed with organic coconut oil (OCO) during turning of hardened D2 steel. The application of cutting fluid on the cutting interface was performed through Minimum Quantity Lubrication (MQL) approach keeping an eye on the detrimental consequences of conventional flood cooling. PVD coated (TiN/TiCN/TiN) cermet tool was employed in the current experimental work. Taguchi’s L9 orthogonal array and TOPSIS are executed to analysis the influences, significance and optimum parameter settings for predefined process parameters. The prime objective of the current work is to analyze the influence of OCO based Trihexyltetradecylphosphonium Chloride ionic fluid on flank wear, surface roughness, material removal rate, and chip morphology. Better quality of finish (Ra = 0.2 to 1.82 µm) was found with 1% weight fraction but it is not sufficient to control the wear growth. Abrasion, chipping, groove wear, and catastrophic tool tip breakage are recognized as foremost tool failure mechanisms. The significance of responses have been studied with the help of probability plots, main effect plots, contour plots, and surface plots and the correlation between the input and output parameters have been analyzed using regression model. Feed rate and depth of cut are equally influenced (48.98%) the surface finish while cutting speed attributed the strongest influence (90.1%). The material removal rate is strongly prejudiced by cutting speed (69.39 %) followed by feed rate (28.94%) whereas chip reduction coefficient is strongly influenced through the depth of cut (63.4%) succeeded by feed (28.8%). TOPSIS significantly optimized the responses with 67.1 % gain in closeness coefficient.

Effect of SiC-Cu Electrode on Material Removal Rate, Tool Wear and Surface Roughness in EDM Process

2020 ◽  
Vol 38 (9A) ◽  
pp. 1406-1413
Author(s):  
Yousif Q. Laibia ◽  
Saad K. Shather
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
304 Stainless Steel ◽  
Tool Electrode ◽  
Pulse Time ◽  
Edm Process

Electrical discharge machining (EDM) is one of the most common non-traditional processes for the manufacture of high precision parts and complex shapes. The EDM process depends on the heat energy between the work material and the tool electrode. This study focused on the material removal rate (MRR), the surface roughness, and tool wear in a 304 stainless steel EDM. The composite electrode consisted of copper (Cu) and silicon carbide (SiC). The current effects imposed on the working material, as well as the pulses that change over time during the experiment. When the current used is (8, 5, 3, 2, 1.5) A, the pulse time used is (12, 25) μs and the size of the space used is (1) mm. Optimum surface roughness under a current of 1.5 A and the pulse time of 25 μs with a maximum MRR of 8 A and the pulse duration of 25 μs.

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

Sign in / Sign up

Export Citation Format

Share Document