Calculation and Characterization of Silicon-Boron Phases in Metallurgical Grade Silicon

Silicon ◽  
2012 ◽  
Vol 4 (4) ◽  
pp. 289-295 ◽  
Author(s):  
Jijun Wu ◽  
Wenhui Ma ◽  
Bin Yang ◽  
Dachun Liu ◽  
Yongnian Dai
1990 ◽  
Vol 5 (9) ◽  
pp. 1894-1899 ◽  
Author(s):  
J. C. Anglézio ◽  
C. Servant ◽  
F. Dubrous

Optical metallography, scanning electron microscopy, electron microprobe analysis, and transmission electron microscopy were used to characterize metallurgical grade silicon, produced in an electric are furnace. Coincidence fraction determinations were assumed to be Σ7 and Σ9 when grain boundaries are underlined by precipitated phases and Σ3 when they are not. The study of intergranular compounds was emphasized; ten compounds were found, the main ones being Si2Ca, Si8Al6Fe4Ca, Si2Al2Ca, Si2FeTi, and Si2.4Fe (α leboitc). The precipitation of these compounds was discussed according to the principal impurity concentrations in silicon. The crystalline structure of Si8Al6Fe4Ca was determined to be triclinic with a = 1.3923 nm, b = 1.3896 nm, c = 1.3900 nm and α = 92.4°, β = 110.3°, γ = 119.9°.


2015 ◽  
Vol 270 ◽  
pp. 98-103 ◽  
Author(s):  
Eloi Kewes ◽  
Franck Dahlem ◽  
Sandrine Bec ◽  
Nicolas Estime ◽  
Khalid Hoummada ◽  
...  

Author(s):  
Erlend L. Bjørnstad ◽  
Gabriella Tranell

AbstractOxidative ladle refining (OLR) is the most used refining method in industrial production of metallurgical grade silicon. OLR is performed by purging the liquid alloy with oxygen-enhanced air at 1823 K to 1873 K, reacting with silicon and the primary slag forming impurities to a SiO$$_{2}$$ 2 -CaO-Al$$_{2}$$ 2 O$$_{3}$$ 3 slag. To further increase our capability to control this process, it is paramount to understand how the slag nucleates and forms, and represent it such that it is useful for predicting and controlling the process behavior. This work aims to formulate a comprehensive theoretical description of slag nucleation and formation at nano/microscale using classical macroscale thermodynamics, bridging these spatial regimes. To achieve this, the work argues that silica’s liquid structure allows its nuclei to exhibit “well defined” surfaces. Furthermore, silica is predicted to be highly surface active, so if its concentration is high while the slag nucleus is small, the SiO$$_{2}$$ 2 -CaO-Al$$_{2}$$ 2 O$$_{3}$$ 3 slag should retain silica’s surface properties. An experiment confirmed the surface active nature of silica in the SiO$$_{2}$$ 2 -CaO-Al$$_{2}$$ 2 O$$_{3}$$ 3 system. It was also shown that increasing the slag’s calcia concentration has a greater effect on the interfacial tension between the molten slag and liquid alloy than alumina, confirming industrial observations of the coupling between refining rate and relative alloy/slag composition.


Vacuum ◽  
2011 ◽  
Vol 86 (4) ◽  
pp. 471-475 ◽  
Author(s):  
Xu Peng ◽  
Wei Dong ◽  
Yi Tan ◽  
Dachuan Jiang

2010 ◽  
Vol 156-157 ◽  
pp. 882-885 ◽  
Author(s):  
Yu Yan Hu ◽  
Dong Liang Lu ◽  
Tao Lin ◽  
Yu Liu ◽  
Bo Wang ◽  
...  

Refining of solar grade silicon by metallurgical method is the research hotspot of polycrystalline field. Slagging method is benefit to the removal of the impurities especially to boron exsisted in the raw silicon. In this study, the influence of the density, the viscosity and liquidus temperature of the slag components on the refining process were discussed, and then the slag system SiO2-Na2CO3 was choosed as the slagging agents. And then the impact factors on the removal efficiency of boron such as the composition of SiO2 and Na2CO3, the ratio of slag to silicon and the refining time were investigated by the orthogonal experiment. The results showed that the optimum parameters of the oxidation refining for removing boron were as follows: the main composition of the oxidant is “SiO2 : Na2CO3 = 60% : 40%”; the slag/silicon ratio is 0.5; time for refining is 60min at 1550 . The results indicated that the removal efficiency of boron was 88.28%, and the content of boron in MG-Si can be reduced to 7ppmw under the best refining process¬.


2004 ◽  
Vol 230-232 ◽  
pp. 1-16 ◽  
Author(s):  
William M. Vetter

Synchrotron white-beam x-ray topographs taken in the back-reflection mode have proved a powerful tool in the study of defects in semiconductor-grade silicon carbide crystals. Capable of mapping the distribution of axial dislocations across a wafer's area (notably the devastating micropipe defect), it can also provide information on their natures. Under favorable conditions, various other types of defect may be observed in back-reflection topographs of SiC, among which are subgrain boundaries, inclusions, and basal plane dislocations. Observed defect images in backreflection topographs may be simulated using relatively simple computer algorithms based on ray tracing. It has been possible to use back-reflection topographs of SiC substrates with device structures deposited upon them to relate the incidence of defects to device failure.


2011 ◽  
Vol 324 ◽  
pp. 324-327 ◽  
Author(s):  
Sarah Darwiche ◽  
Malek Benmansour ◽  
Nir Eliezer ◽  
Daniel Morvan

Laser-induced breakdown spectroscopy (LIBS) has been employed for the fast and reliable chemical characterization of silicon used for the photovoltaic industry. Silicon for photovoltaic panels is subject to certain constraints on its purity, and notably must contain low concentration of boron. The use of LIBS could be advantageous because it allows rapid and simultaneous multi-elemental chemical analysis of silicon without any sample preparation. LIBS was applied to boron analysis and a detection limit of 0.23 ppmw was found for optimized gas and pressure conditions.


2018 ◽  
Vol 115 (3) ◽  
pp. 312 ◽  
Author(s):  
Rowaid Al-khazraji ◽  
Yaqiong Li ◽  
Lifeng Zhang

Boron (B) removal by slag refining using CaO–SiO2–CaCl2 was investigated in metallurgical-grade silicon (MG-Si) and 75 wt% Si–Sn alloy. Experiments were conducted at 1500 °C for 15 min. The microstructure was characterized before and after refining. The effects of acid leaching, basicity, and slag/Si mass ratio on B removal were investigated. Experimental results showed that acid leaching had no effect on B removal from MG-Si but had a clear effect on the refined Si–Sn alloy after slag refining. The final B concentration was highly affected by the CaO/SiO2 mass ratio with minimum value, where the content of B was reduced from 18.36 ppmw to 5.5 ppmw at the CaO/SiO2 = 1.2 for MG-Si slag refining and from 18.36 ppmw to 3.7 ppmw at CaO/SiO2 = 1.5 for 75 wt% Si–Sn alloy. Increasing the slag mass ratio by 2:1 mass ratio also increased B removal efficiency by approximately 15–20% more than an increase by 1:1.


Sign in / Sign up

Export Citation Format

Share Document