scholarly journals Enhanced removal of cationic dye by eco-friendly activated biochar derived from rice straw

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
A. I. Abd-Elhamid ◽  
Mohamed Emran ◽  
M. H. El-Sadek ◽  
Ahmed A. El-Shanshory ◽  
Hesham M. A. Soliman ◽  
...  
Keyword(s):  
Rice Straw ◽  
Contact Time ◽  
Ph Value ◽  
Active Material ◽  
Maximum Adsorption Capacity ◽  
Time Data ◽  
Experimental Conditions ◽  
Activated Biochar ◽  
Highly Active ◽  
Pseudo Second Order

AbstractThis report deals with converting the agriculture waste (rice straw) to environmental cleaner materials (biochar) using airless pyrolysis followed by eco-friendly activation. The biochar (p-Biochar) obtained after pyrolysis step (poorly active material) was activated using wet attrition method to give m-Biochar (highly active materials). The both p-Biochar and m-Biochar were characterized in detail and utilized for MB and CV dye removal from aqueous solution. Various parameters affecting the adsorption process such as dye concentration, adsorbent dose, contact time, temperature, NaCl dose and pH were investigated. The adsorption isotherm was well fitted using Langmuir isotherm, and the maximum adsorption capacity is 90.91 and 44.64 mg/g, for MB and CV dyes, respectively. The contact time data obtained showed that the two dyes were poorly adsorbed over p-Biochar. The equilibrium was reached quickly in 15 min for MB dye and 20 min for CV dye using the m-Biochar, and removal percent was 94.45 and 92.70% for MB and CV dyes, respectively. Moreover, the kinetic isotherm presented very well fitted by pseudo-second-order model. In addition, the adsorption percent increases with further increasing the pH value. Finally, we observed that m-Biochar highly adsorbs the MB dye compared with the CV dye over all experimental conditions.

scholarly journals DEVELOPMENT AND VALIDATION OF A SPECTROPHOTOMETRIC METHOD TO EVALUATE BIOSAFETY CAPACITY OF BARU (Dipteryx alata) PEELS

2018 ◽  
Vol 15 (30) ◽  
pp. 221-240
Author(s):  
E. C. CESARINO ◽  
D. S. MULHOLLAND ◽  
W. FRANCISCO
Keyword(s):  
Contact Time ◽  
Limit Of Detection ◽  
Copper Ions ◽  
Maximum Adsorption Capacity ◽  
Limit Of Quantification ◽  
Experimental Conditions ◽  
Inorganic Matter ◽  
Pseudo Second Order ◽  
Development And Validation ◽  
Dipteryx Alata

This study developed a new analytical method using Molecular Absorption Spectroscopy (MAS) to track the ion cover in adsorption solution per peel (mesocarp) of Baru (Dipteryx alata). The adsorption study was conducted at different pH and contact time (kinetic), encountering 4.0 as the best pH for adsorption experimental conditions. The variation of contact time showed a pseudo-second-order adsorption kinetic behavior. The interpretation of the isotherms allowed to approach the Langmuir model with R² of 0.918 and to determine the maximum adsorption capacity (qmáx) as 11.481 mg.g⁻¹. The characterization of biomass by MAS in the Infrared (FT-IR) identified the possible functional groups belonging to protein, fatty acids and lipids, while thermal analysis (TG-DSC) showed a greater removal of inorganic matter by the biomass washed with water. The method underwent analytical validation, being classified as specific, sensitive, linear, robust, precise and accurate, with LD (limit of detection) and LQ (limit of quantification) equal to 3.873 and 12.912 mg.L⁻¹, respectively. The results obtained demonstrated the potential use of mesocarp Baru as a natural adsorbent for copper ions in solution, opening power for future expansion and improvement of the method.

scholarly journals Preparation of chitosan/amine modified diatomite composites and adsorption properties of Hg(II) ions

2018 ◽  
Vol 77 (5) ◽  
pp. 1363-1371 ◽  
Author(s):  
Yong Fu ◽  
Yue Huang ◽  
Jianshe Hu ◽  
Zhengjie Zhang
Keyword(s):  
Schiff Base ◽  
Contact Time ◽  
Ph Value ◽  
Adsorption Properties ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Adsorption Effect ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Modified Diatomite

Abstract A green functional adsorbent (CAD) was prepared by Schiff base reaction of chitosan and amino-modified diatomite. The morphology, structure and adsorption properties of the CAD were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy and Brunauer Emmett Teller measurements. The effect of pH value, contact time and temperature on the adsorption of Hg(II) ions for the CAD is discussed in detail. The experimental results showed that the CAD had a large specific surface area and multifunctional groups such as amino, hydroxyl and Schiff base. The optimum adsorption effect was obtained when the pH value, temperature and contact time were 4, 25 °C and 120 min, respectively, and the corresponding maximum adsorption capacity of Hg(II) ions reached 102 mg/g. Moreover, the adsorption behavior of Hg(II) ions for the CAD followed the pseudo-second-order kinetic model and Langmuir model. The negative ΔG0 and ΔH0 suggested that the adsorption was a spontaneous exothermic process.

Characteristics of Cu2+ Adsorption by Modified Rice Straw

2013 ◽  
Vol 726-731 ◽  
pp. 2622-2628
Author(s):  
Ming Da Liu ◽  
Lei Guo ◽  
Jun Yang ◽  
Yao Jing Wang
Keyword(s):  
Rice Straw ◽  
Ph Value ◽  
Removal Rate ◽  
Maximum Adsorption Capacity ◽  
Static State ◽  
Metal Biosorption ◽  
Initial Ph ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Sorption Time

In this paper, modified rice straw was investigated for its Cu2+removal ability from aqueous solution. The effects of environmental factors on metal biosorption were studied under static state, including initial concentration of metal ions, sorption time, initial pH value and adsordent dosage. In addition, the relevant equilibrium, kinetics were discussed. The results showed that the rice straw which was modified by NaOH had been improved greatly in its Cu2+removal ability. The rice straw had good effects on adsorption of low concentration of Cu2+solution. The adsorption data fit Langmuir isotherm model well, the maximum adsorption capacity for Cu2+reached 8.48 mg·g-1. The adsorption of Cu2+on the modified rice straw was a very rapid process, the kinetics fit a pseudo-second-order equation well. The pH value had prominent effect on the removal rate of Cu2+, adsorption efficient could reach over 92% when pH value was between 5 and 6.5. With increasing adsordent dosage, the removal rate of Cu2+increased.

scholarly journals Equilibrium and Kinetics Study of Adsorption of Crystal Violet onto the Peel ofCucumis sativaFruit from Aqueous Solution

2012 ◽  
Vol 9 (3) ◽  
pp. 1091-1101 ◽  
Author(s):  
T. Smitha ◽  
S. Thirumalisamy ◽  
S. Manonmani
Keyword(s):  
Crystal Violet ◽  
Dye Removal ◽  
High Efficiency ◽  
Ph Value ◽  
Dye Adsorption ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Experimental Conditions ◽  
Pseudo Second Order ◽  
Cucumis Sativa

The use of low-cost, locally available, high efficiency and eco-friendly adsorbents has been investigated as an ideal alternative to the current expensive methods of removing dyes from wastewater. This study investigates the potential use of the peel ofCucumis sativafruit for the removal of crystal violet (CV) dye from simulated wastewater. The effects of different system variables, adsorbent dosage, initial dye concentration, pH and contact time were investigated and optimal experimental conditions were ascertained. The results showed that as the amount of the adsorbent increased, the percentage of dye removal increased accordingly. Optimum pH value for dye adsorption was determined as 7.0. The adsorption of crystal violet followed pseudo-second order rate equation and fit well Langmuir and Freundlich equations. The maximum removal of CV was obtained at pH 7 as 92.15% for adsorbent dose of 0.2 g/50 mL and 25 mg L-1initial dye concentration at room temperature. The maximum adsorption capacity obtained from Langmuir equation was 34.24 mg g-1. Furthermore, adsorption kinetics of (CV) was studied and the rate of adsorption was found to conform to pseudo-second order kinetics with a good correlation (R2> 0.9739). The peel ofCucumis sativafruit can be attractive options for dye removal from diluted industrial effluents since test reaction made on simulated dyeing wastewater show better removal percentage of (CV).

Adsorption of Dye from Wastewater by Modified Sawdust

2014 ◽  
Vol 1065-1069 ◽  
pp. 3123-3126
Author(s):  
Gang Chao Zhu ◽  
Jian Xin Shou ◽  
Jia Wei Qian ◽  
Hua Zheng Xin ◽  
Mu Qing Qiu
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Ph Value ◽  
Langmuir Model ◽  
Ammonium Bromide ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Adsorption Processes ◽  
Endothermic Process ◽  
Pseudo Second Order

In this study, sawdust modified by cetyltimethyl ammonium bromide was applied to adsorb conge red in aqueous solutions. The characteristics of modified sawdust were characterized by Fourier transform infrared spectrum and scanning electron microscopy. The effect of factors, such as pH, contact time, temperature, dosage, and salt concentration, were investigated. The results revealed that the addition of modified sawdust can significantly increase the adsorption capacity of dye. The maximum adsorption capacity of dye on modified sawdust was 109 mg·g-1 at 328K. The adsorption processes were rapid within the first 30 min and reached equilibrium in about 150 min. The adsorption kinetics fitted well with pseudo-second-order model. The pH value of the solution had significant impact on the amount of adsorption. Adsorption isotherm fitted better with the Langmuir model and the adsorption was an endothermic process

scholarly journals The nature and kinetics of 2,4-dimethylphenol adsorption in aqueous solution on biochar derived from Sargassum boveanum macroalgae

2020 ◽  
Vol 69 (5) ◽  
pp. 438-452 ◽  
Author(s):  
Mazen K. Nazal ◽  
Durga Rao ◽  
Nabeel Abuzaid
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Experimental Conditions ◽  
Freundlich Model ◽  
Adsorptive Removal ◽  
Adsorbate Concentration ◽  
Pseudo Second Order ◽  
Kinetics Of

Abstract Many industries produce 2,4-dimethylphenol (DMP) compound in the wastewater which is persistent, toxic, and carcinogenic. Therefore, an adsorbent was prepared by carbonizing a dried Sargassum boveanum macroalgae. The prepared biosorbent was investigated for adsorptive removal of DMP from aqueous solution. After carbonization, the biochar derived from S. boveanum macroalgae (BCM) removed almost 100% of DMP adsorbate. Effects of contact time, solution pH, adsorbate concentration, adsorbent mass, and temperature have been studied. It has been found that, within the experimental conditions, the maximum adsorption capacity is 17 mg/g, rate of adsorption follows pseudo-second order kinetics and the adsorption isotherm experimental data fit the Freundlich model. The thermodynamic parameters were calculated and it has been found that the adsorption of DMP on BCM is endothermic and thermodynamically favorable, and in addition the surface of BCM adsorbent shows affinity to the DMP molecules. The BCM adsorbent has the capability to remove around 65% of DMP from high saline seawater contaminated with DMP. Moreover, the prepared BCM adsorbent was reusable for at least four times in seawater for removal of DMP contaminant.

scholarly journals Cr6+ adsorption by modified vermiculite

2020 ◽  
Author(s):  
Valeria Medoro ◽  
Celia Marcos Pascual ◽  
Giacomo Ferretti ◽  
Giulio Galamini ◽  
Massimo Coltorti
Keyword(s):  
Earth Sciences ◽  
Inductively Coupled Plasma ◽  
Contact Time ◽  
Second Order ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Experimental Conditions ◽  
X Ray ◽  
Pseudo Second Order

<p><strong>Abstract</strong>: <strong>Cr<sup>6+</sup> adsorption by modified vermiculite</strong></p><p><strong> </strong></p><p>Valeria Medoro- University of Ferrara , Department of Physics and Earth Sciences, Italy</p><p>Celia Marcos Pascual-University of Oviedo, Department of Geology, Spain</p><p>Giacomo Ferretti- University of Ferrara , Department of Physics and Earth Sciences, Italy</p><p>Giulio Galamini- University of Ferrara , Department of Physics and Earth Sciences, Italy</p><p>Massimo Coltorti- University of Ferrara , Department of Physics and Earth Sciences, Italy</p><p> </p><p>This work aimed at investigating the adsorption of Cr<sup>6+</sup> in water by exfoliated vermiculite. The adsorbant tested in this experiment was a vermiculite (from China) which has been subjected to heating at 1000 °C for 1 minute, resulting in an exfoliated vermiculite.</p><p>Three effects were studied: 1) contact time; 2) initial concentracion of Cr<sup>6+</sup>; 3) adsorbent mass. Samples were analysed by X Ray Fluorescence (XRF), X Ray Diffraction (XRD) and the solutions with Inductively Coupled Plasma Mass Spectrometry (ICP-MS) to quantify the adsorbed Cr<sup>6+</sup> by the vermiculite.</p><p>Results from XRD diffraction showed a conversion of vermiculite into flogopite  after heating at 1000°C for 1 minute because of: 1) high content of potassium, 2) dehydration and 3) structural re-ordering; after the contact of vermiculite with Cr<sup>6+</sup>, the mineral structure did not change. The adsorption of Cr<sup>6+</sup> was studied by Langmuir, Freundlich and Dubinin-Kaganer-Radushkevich (DKR) isotherm models. DKR model, indicative of a cooperative process, described adsorption equilibrium better than the other two models and the maximum adsorption capacity obtained was of 2.81 mol/g. Kinetic was studied using pseudo-first and pseudo-second order kinetic models, with a better description of the process by pseudo-second order model with correlation coefficient almost unitary (R<sup>2</sup>=0.9984; other kinetic parameters were k<sub>2</sub>=0.0015 and the absorption initial rate of 0.2x10<sup>-8</sup> mg g<sup>-1</sup> h<sup>-1</sup>). </p><p>The present study demonstrates the effectiveness of modified vermiculite adsorbents for the treatment of hexavalent chromium-contaminated waters and that its adsorption depends on the experimental conditions (such as contact time, initial concentracion of Cr<sup>6+</sup> and adsorbent mass).</p>

Nano-ZrO2/TiO2 Impregnated Orange Wood Sawdust and Peach Stone Shell Adsorbents for Cr (VI) Removal

2020 ◽  
Vol 16 (7) ◽  
pp. 880-892
Author(s):  
Şerife Parlayıcı ◽  
Kübra Tuna Sezer ◽  
Erol Pehlivan
Keyword(s):  
Contact Time ◽  
Ph Value ◽  
Order Kinetic ◽  
Adsorption Parameters ◽  
Wood Sawdust ◽  
Adsorption Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Equilibrium Status

Background: In this work, Cr (VI) adsorption on nano-ZrO2๏TiO2 impregnated orange wood sawdust (Zr๏Ti/OWS) and nano-ZrO2๏TiO2 impregnated peach stone shell (Zr๏Ti/PSS) was investigated by applying different adsorption parameters such as Cr (VI) concentrations, contact time, adsorbent dose, and pH for all adsorbents. Methods: The adsorbents were characterized by SEM and FT-IR. The equilibrium status was achieved after 120 min of contact time and optimum pH value around 2 were determined for Cr (VI) adsorption. Adsorption data in the equilibrium is well-assembled by the Langmuir model during the adsorption process. Results: Langmuir isotherm model showed a maximum adsorption value of OWS: 21.65 mg/g and Zr๏Ti/OWS: 27.25 mg/g. The same isotherm displayed a maximum adsorption value of PSS: 17.64 mg/g, and Zr๏Ti/PSS: 31.15 mg/g. Pseudo-second-order kinetic models (R2=0.99) were found to be the best models for describing the Cr (VI) adsorption reactions. Conclusıon: Thermodynamic parameters such as changes in ΔG°, ΔH°, and ΔS° have been estimated, and the process was found to be spontaneous.

scholarly journals Zeolite NaP1 Functionalization for the Sorption of Metal Complexes with Biodegradable N-(1,2-dicarboxyethyl)-D,L-aspartic Acid

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2518
Author(s):  
Dorota Kołodyńska ◽  
Yongming Ju ◽  
Małgorzata Franus ◽  
Wojciech Franus
Keyword(s):  
Experimental Data ◽  
Aspartic Acid ◽  
Ph Value ◽  
Complexing Agents ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
Modified Zeolite ◽  
X Ray ◽  
Slow Release Fertilizers ◽  
Pseudo Second Order

The possibility of application of chitosan-modified zeolite as sorbent for Cu(II), Zn(II), Mn(II), and Fe(III) ions and their mixtures in the presence of N-(1,2-dicarboxyethyl)-D,L-aspartic acid, IDHA) under different experimental conditions were investigated. Chitosan-modified zeolite belongs to the group of biodegradable complexing agents used in fertilizer production. NaP1CS as a carrier forms a barrier to the spontaneous release of the fertilizer into soil. The obtained materials were characterized by Fourier transform infrared spectroscopy (FTIR); surface area determination (ASAP); scanning electron microscopy (SEM-EDS); X-ray fluorescence (XRF); X-ray diffraction (XRD); and carbon, hydrogen, and nitrogen (CHN), as well as thermogravimetric (TGA) methods. The concentrations of Cu(II), Zn(II), Mn(II), and Fe(III) complexes with IDHA varied from 5–20 mg/dm3 for Cu(II), 10–40 mg/dm3 for Fe(III), 20–80 mg/dm3 for Mn(II), and 10–40 mg/dm3 for Zn(II), respectively; pH value (3–6), time (1–120 min), and temperature (293–333 K) on the sorption efficiency were tested. The Langmuir, Freundlich, Dubinin–Radushkevich, and Temkin adsorption models were applied to describe experimental data. The pH 5 proved to be appropriate for adsorption. The pseudo-second order and Langmuir models were consistent with the experimental data. The thermodynamic parameters indicate that adsorption is spontaneous and endothermic. The highest desorption percentage was achieved using the HCl solution, therefore, proving that method can be used to design slow-release fertilizers.

Removal of Methylene Blue and Orange-G from Waste Water Using Magnetic Biochar

2015 ◽  
Vol 14 (04) ◽  
pp. 1550009 ◽  
Author(s):  
N. M. Mubarak ◽  
Y. T. Fo ◽  
Hikmat Said Al-Salim ◽  
J. N. Sahu ◽  
E. C. Abdullah ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Contact Time ◽  
Agitation Speed ◽  
Adsorption Kinetic ◽  
Maximum Adsorption Capacity ◽  
Optimum Conditions ◽  
Magnetic Biochar ◽  
Design Expert ◽  
Orange G ◽  
Pseudo Second Order

The study on the removal of methylene blue (MB) and orange-G dyes using magnetic biochar derived from the empty fruit bunch (EFB) was carried out. Process parameters such as pH, adsorbent dosage, agitation speed and contact time were optimized using Design-Expert Software v.6.0.8. The statistical analysis reveals that the optimum conditions for the maximum adsorption of MB are at pH 2 and pH 10, dosage 1.0 g, and agitation speed and contact time of 125 rpm and 120 min respectively. While for orange-G, at pH 2, dosage 1.0 g, and agitation speed and contact time of 125 rpm and 120 min respectively. The maximum adsorption capacity of 31.25 mg/g and 32.36 mg/g for MB and orange-G respectively. The adsorption kinetic for both dyes obeyed pseudo-second order.

Sign in / Sign up

Export Citation Format

Share Document