The effect of functionalisation method on the stability and the thermal conductivity of nanofluid hybrids of carbon nanotubes/gamma alumina

2013 ◽  
Vol 39 (4) ◽  
pp. 3885-3891 ◽  
Author(s):  
Saloumeh Mesgari Abbasi ◽  
Alimorad Rashidi ◽  
Ali Nemati ◽  
Kaveh Arzani
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Gamma Alumina ◽  
The Stability

Thermal Conductivity Measurement for Carbon-Nanotube Suspensions with 3ω Method

2009 ◽  
Vol 60-61 ◽  
pp. 394-398 ◽  
Author(s):  
Gen Sheng Wu ◽  
Jue Kuan Yang ◽  
Shu Lin Ge ◽  
Yu Juan Wang ◽  
Min Hua Chen ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Volume Fraction ◽  
Aqueous Suspension ◽  
Conductivity Measurement ◽  
3Ω Method ◽  
Conductivity Enhancement ◽  
Multi Walled Carbon Nanotubes ◽  
The Stability ◽  
Walled Carbon Nanotubes

The stable and homogeneneous aqueous suspension of carbon nanotubes was prepared in this study. The stability of the nanofluids was improved greatly due to the use of a new dispersant, humic acid. The thermal conductivity of the aqueous suspension was measured with the 3ω method. The experimental results showed that the thermal conductivity of the suspensions increases with the temperature and also is nearly proportional to the loading of the nanoparticles. The thermal conductivity enhancement of single-walled carbon nanotubes (SWNTs) suspensions is better than that of the multi-walled carbon nanotubes (MWNTs) suspensions. Especially for a volume fraction of 0.3846% SWNTs, the thermal conductivity is enhanced by 40.5%. Furthermore, the results at 30°C match well with Jang and Choi’s model.

scholarly journals Thermophysical Properties of Nanofluids Composed of Ethylene Glycol and Long Multi-Walled Carbon Nanotubes

Fluids ◽  
2020 ◽  
Vol 5 (4) ◽  
pp. 241
Author(s):  
Karolina Brzóska ◽  
Bertrand Jóźwiak ◽  
Adrian Golba ◽  
Marzena Dzida ◽  
Sławomir Boncel
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Ethylene Glycol ◽  
Chemical Vapor ◽  
Step Method ◽  
Mwcnt Content ◽  
Multi Walled Carbon Nanotubes ◽  
The Stability ◽  
Walled Carbon Nanotubes ◽  
Rotary Viscometer

In this work, thermal conductivity, viscosity, isobaric heat capacity, and density of stable carbon-based nanofluids are presented. The nanofluids under study are composed of 1,2-ethanediol (ethylene glycol, EG) and long multi-walled carbon nanotubes (MWCNTs), so-called ‘in-house 16h’ (synthesized in our laboratory via catalytic chemical vapor deposition during 16 h with a diameter of 60–80 nm and length of 770 μm). Poly(N-vinylpyrrolidone) (PVP) was used to increase the stability of nanofluids. The nanofluids were prepared via an ultrasonication-assisted, three-step method while their key thermophysical characteristics were obtained using the hot-wire technique and rotary viscometer. As a result, the addition of MWCNTs significantly improved the thermal conductivity of nanofluids by 31.5% for the highest 1.0 wt% (0.498 vol%) long MWCNT content, leaving the Newtonian character of the nanofluids practically intact.

scholarly journals Thermal Conductivity of CNT - Wated Nanofluids: a Review

2020 ◽  
Vol 22 (1) ◽  
pp. 207-220 ◽  
Author(s):  
M. Akhilesh ◽  
K. Santarao ◽  
M. V. S. Babu
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Experimental Studies ◽  
Thermal Characteristics ◽  
Thermal Conducting ◽  
The Stability ◽  
Proper Group ◽  
Physical Stabilization ◽  
Transportation Applications

AbstractIn heat transportation applications, water is most commonly used fluid. The efficiency of equipment used in these applications depends on thermal characteristics of water used. The thermal characteristics of water could be upgraded by suspending high thermal conducting solid nanoparticles. In this paper an attempt has been made to know how the use of surfactants and functionalization of carbon nanotube walls can affect the thermal characteristics and stability of nanofluid. A thorough analysis of collected literature revealed that carbon nanotubes have much higher thermal conductivity than any other nanoparticles and hence improve the thermal properties of water when suspended in them. Further it is concluded that suspension of carbon nanotubes in water requires use of surfactant or functionalization of carbon nanotube walls with proper group. By setting optimum pH and better dispersion, better thermal conductivity is possible. Experimental studies in the literature survey reveal that chemical stabilization techniques and physical stabilization techniques together decide the stability of the nanofluid.

An Experimental Investigation on Thermal Conductivity and Viscosity of Graphene doped CNTs /TiO2 Nanofluid

2020 ◽  
Vol 17 (3) ◽  
Author(s):  
A.M. Zetty Akhtar ◽  
M.M. Rahman ◽  
K. Kadirgama ◽  
M.A. Maleque
Keyword(s):  
Thermal Conductivity ◽  
Zeta Potential ◽  
Base Fluid ◽  
Minimum Quantity Lubrication ◽  
Cutting Fluid ◽  
Cutting Zone ◽  
Observation Method ◽  
The Stability ◽  
The Relationship ◽  
Zeta Potential Analysis

This paper presents the findings of the stability, thermal conductivity and viscosity of CNTs (doped with 10 wt% graphene)- TiO2 hybrid nanofluids under various concentrations. While the usage of cutting fluid in machining operation is necessary for removing the heat generated at the cutting zone, the excessive use of it could lead to environmental and health issue to the operators. Therefore, the minimum quantity lubrication (MQL) to replace the conventional flooding was introduced. The MQL method minimises the usage of cutting fluid as a step to achieve a cleaner environment and sustainable machining. However, the low thermal conductivity of the base fluid in the MQL system caused the insufficient removal of heat generated in the cutting zone. Addition of nanoparticles to the base fluid was then introduced to enhance the performance of cutting fluids. The ethylene glycol used as the base fluid, titanium dioxide (TiO2) and carbon nanotubes (CNTs) nanoparticle mixed to produce nanofluids with concentrations of 0.02 to 0.1 wt.% with an interval of 0.02 wt%. The mixing ratio of TiO2: CNTs was 90:10 and ratio of SDBS (surfactant): CNTs was 10:1. The stability of nanofluid checked using observation method and zeta potential analysis. The thermal conductivity and viscosity of suspension were measured at a temperature range between 30˚C to 70˚C (with increment of 10˚C) to determine the relationship between concentration and temperature on nanofluid’s thermal physical properties. Based on the results obtained, zeta potential value for nanofluid range from -50 to -70 mV indicates a good stability of the suspension. Thermal conductivity of nanofluid increases as an increase of temperature and enhancement ratio is within the range of 1.51 to 4.53 compared to the base fluid. Meanwhile, the viscosity of nanofluid shows decrements with an increase of the temperature remarks significant advantage in pumping power. The developed nanofluid in this study found to be stable with enhanced thermal conductivity and decrease in viscosity, which at once make it possible to be use as nanolubricant in machining operation.

An analysis of the transport properties and mechanical stability of rapidly solidified Al-Sb alloy

2015 ◽  
Vol 10 (2) ◽  
pp. 2663-2681
Author(s):  
Rizk El- Sayed ◽  
Mustafa Kamal ◽  
Abu-Bakr El-Bediwi ◽  
Qutaiba Rasheed Solaiman
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Melt Spinning ◽  
Elastic Moduli ◽  
Mechanical Stability ◽  
Microstructural Analysis ◽  
Alloy System ◽  
Antimony Content ◽  
The Stability ◽  
Rapidly Solidified

The structure of a series of AlSb alloys prepared by melt spinning have been studied in the as melt–spun ribbons  as a function of antimony content .The stability  of these structures has  been  related to that of the transport and mechanical properties of the alloy ribbons. Microstructural analysis was performed and it was found that only Al and AlSb phases formed for different composition.  The electrical, thermal and the stability of the mechanical properties are related indirectly through the influence of the antimony content. The results are interpreted in terms of the phase change occurring to alloy system. Electrical resistivity, thermal conductivity, elastic moduli and the values of microhardness are found to be more sensitive than the internal friction to the phase changes. 

A model for thermal conductivity of carbon nanotubes with ethylene glycol/water based nanofluids

2017 ◽  
Vol 59 (02) ◽  
pp. 10-13
Author(s):  
Trong Tam Nguyen ◽  
◽  
Hung Thang Bui ◽  
Ngoc Minh Phan ◽  
◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Ethylene Glycol ◽  
Water Based

scholarly journals Effect of Size of Multiwalled Carbon Nanotubes Dispersed in Gear Oils for Improvement of Tribological Properties

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Kodanda Rama Rao Chebattina ◽  
V. Srinivas ◽  
N. Mohan Rao
Keyword(s):  
Carbon Nanotubes ◽  
Raman Spectroscopy ◽  
Ball Milling ◽  
Multiwalled Carbon Nanotubes ◽  
Tribological Properties ◽  
Extreme Pressure ◽  
Multiwalled Carbon ◽  
Pristine Mwcnts ◽  
Gear Oil ◽  
The Stability

The aim of the paper is to investigate the effect of size of multiwalled carbon nanotubes (MWCNTs) as additives for dispersion in gear oil to improve the tribological properties. Since long pristine MWCNTs tend to form clusters compromising dispersion stability, they are mildly processed in a ball mill to shorten the length and stabilized with a surfactant before dispersing in lubricant. Investigations are made to assess the effect of ball milling on the size and structure of MWCNTs using electron microscopy and Raman spectroscopy. The long and shortened MWCNTs are dispersed in EP 140 gear oil in 0.5% weight. The stability of the dispersed multiwalled carbon nanotubes is evaluated using light scattering techniques. The antiwear, antifriction, and extreme pressure properties of test oils are evaluated on a four-ball wear tester. It is found that ball milling of MWCNTs has a strong effect on the stability and tribological properties of the lubricant. From Raman spectroscopy, it is found that ball milling time of up to 10 hours did not produce any defects on the surface of MWCNTs. The stability of the lubricant and the antiwear, antifriction, and extreme pressure properties have improved significantly with dispersion shortened MWCNTs. Ball milling for longer periods produces defects on the surface of MWCNTs reducing their advantage as oil additives.

scholarly journals Dispersion of Carbon Nanotubes with “Green” Detergents

Molecules ◽  
2021 ◽  
Vol 26 (10) ◽  
pp. 2908
Author(s):  
Kazuo Umemura ◽  
Ryo Hamano ◽  
Hiroaki Komatsu ◽  
Takashi Ikuno ◽  
Eko Siswoyo
Keyword(s):  
Carbon Nanotubes ◽  
Sodium Dodecyl ◽  
Detergent Solution ◽  
Absorbance Spectroscopy ◽  
Fundamental Research ◽  
The Stability ◽  
Single Walled Cnts ◽  
Better Than ◽  
Walled Cnts ◽  
Cnt Suspensions

Solubilization of carbon nanotubes (CNTs) is a fundamental technique for the use of CNTs and their conjugates as nanodevices and nanobiodevices. In this work, we demonstrate the preparation of CNT suspensions with “green” detergents made from coconuts and bamboo as fundamental research in CNT nanotechnology. Single-walled CNTs (SWNTs) with a few carboxylic acid groups (3–5%) and pristine multi-walled CNTs (MWNTs) were mixed in each detergent solution and sonicated with a bath-type sonicator. The prepared suspensions were characterized using absorbance spectroscopy, scanning electron microscopy, and Raman spectroscopy. Among the eight combinations of CNTs and detergents (two types of CNTs and four detergents, including sodium dodecyl sulfate (SDS) as the standard), SWNTs/MWNTs were well dispersed in all combinations except the combination of the MWNTs and the bamboo detergent. The stability of the suspensions prepared with coconut detergents was better than that prepared with SDS. Because the efficiency of the bamboo detergents against the MWNTs differed significantly from that against the SWNTs, the natural detergent might be useful for separating CNTs. Our results revealed that the use of the “green” detergents had the advantage of dispersing CNTs as well as SDS.

Sign in / Sign up

Export Citation Format

Share Document