The impact of water to cement ratio on the fracture behavior of rubberized concrete

2021 ◽  
pp. 125754
Author(s):  
Amir Ali Emadi ◽  
Amir Modarres
Keyword(s):  
Fracture Behavior ◽  
Rubberized Concrete ◽  
Cement Ratio ◽  
Water To Cement Ratio ◽  
The Impact

scholarly journals Soft Computing and Multi-Scal Model Technics to Predict the Early Age Compression Strength of Cement Paste as a Function of Polymer Contents, Water-to-Cement-Ratio, and Curing Ages

2021 ◽  
Author(s):  
Ahmed Mohammed ◽  
Kawan Ghafor ◽  
Wael Mahmood ◽  
Warzer Sarwar ◽  
Lajan Burhan
Keyword(s):  
Cement Paste ◽  
Compression Strength ◽  
Building Materials ◽  
Training Data ◽  
Early Age ◽  
Polymer Content ◽  
Data Set ◽  
Cement Ratio ◽  
Water To Cement Ratio ◽  
The Impact

Abstract In this study, the effect of two water reducer polymers with smooth and rough surfaces on the compression strength of Ordinary Portland cement (OPC) was investigated. Three different initial ratios between water and cement (w/c) 0.5, 0.6, and 1 were used in this study. The amount of polymer contents varied from 0 to 0.06 % (%wt) for the cement paste with initial w/c of 0.5 and the polymer contents ranged between 0 to 0.16% (%wt) for the cement paste with initial w/c of 0.6 and 1 were investigated. SEM test was conducted to identify the impact of polymers on the behavior of cement paste. The compression strength of OPC cement was increased significantly with increasing the polymer contents. Because of a fiber net (netting) around cement paste particle was developed when the polymers were added to the cement paste which leads to decrease the void between the particles, binding the cement particles, therefore, increased the viscosity and compression strength of the cement rapidly. In this analysis, the hardness of cement paste with polymer contents has been evaluated and modeled using four different model technics. More environmentally sustainable construction, and lower cost than conventional building materials and early age strengths of the cement. To overcome the mentioned matter, this study aims to establish systematic multiscale models to predict the compression strength of cement paste containing polymers and to be used by the construction industry with no theoretical restrictions. For that purpose, a wide data a total of 280 tested cement paste modified with polymers, has been conducted, analyzed, and modeled. Linear, Nonlinear regression, M5P-tree, and Artificial Neural Network (ANN) technical approaches were used for the qualifications. In the modeling process, the most relevant parameters affecting the strength of cement paste, i.e. polymer incorporation ratio (0-0.16% of cement's mass), water-to-cement ratio (0.5-1), and curing ages (1 to 28 days). According to the correlation coefficient (R), mean absolute error and the root means a square error, the compression strength of cement paste can be well predicted in terms of w/c, polymer content, and curing time using four various simulation techniques. Among the used approaches and based on the training data set, the model made based on the Non-linear regression, ANN, and M5P-tree models seem to be the most reliable models. The sensitivity investigation concludes that the polymer content is the most dominating parameter for the prediction of the compression strength of cement paste with this data set.

scholarly journals Experimental Study on Effective Chloride Diffusion Coefficient of Cement Mortar by Different Electrical Accelerated Measurements

Crystals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 240
Author(s):  
Jianlan Chen ◽  
Jiandong Wang ◽  
Rui He ◽  
Huaizhu Shu ◽  
Chuanqing Fu
Keyword(s):  
Diffusion Coefficient ◽  
Cement Mortar ◽  
Early Stage ◽  
Chloride Concentration ◽  
Chloride Diffusion ◽  
Chloride Diffusion Coefficient ◽  
Cement Ratio ◽  
Water To Cement Ratio ◽  
Good Consistency ◽  
Determination Methods

This study investigated the effective chloride diffusion coefficient of cement mortar with different water-to-cement ratio (w/c) under electrical accelerated migration measurement. The cumulative chloride concentration in anode cell solution and the cumulative chloride concentration drop in the cathode cell solution was measured by RCT measurement and the results were further used to calculate the chloride diffusion coefficient by Nordtest Build 355 method and Truc method. The influence of w/c on cement mortar’s chloride coefficient was investigated and the chloride diffusion coefficient under different determination methods were compared with other researchers’ work, a good consistency between this work’s results and literatures’ results was obtained. The results indicated that the increased w/c of cement mortar samples will have a higher chloride diffusion coefficient. The cumulative chloride concentration drop in the cathode cell solution will have deviation in early stage measurement (before 60 h) which will result in overestimation of the effective chloride diffusion coefficient.

scholarly journals Cementitious Composites Reinforced with Polypropylene, Nylon and Polyacrylonitile Fibres

2012 ◽  
Vol 730-732 ◽  
pp. 271-276
Author(s):  
H.R. Pakravan ◽  
M. Jamshidi ◽  
M. Latifi ◽  
F. Pacheco-Torgal
Keyword(s):  
Absorption Capacity ◽  
Cement Matrix ◽  
Cementitious Composites ◽  
Scanning Electron Micrographs ◽  
Energy Absorption Capacity ◽  
Cement Ratio ◽  
Pull Out ◽  
Water To Cement Ratio ◽  
Before And After ◽  
Scanning Electron

This paper compares the adhesion strength between three polymeric fibres (polypropylene (PP), nylon66 (N66) and polyacrylonitrile (PAN)) embedded in a cement paste. The specimens were prepared at a water to cement ratio (w/c) of 0.5 and tested after 7, 14 and 28 curing days. It was found that although the adhesion between the polymeric fibres to the cement matrix is an important factor, the energy absorption capacity or energy dissipation ability of the fibres, plays a more important role in the improvement of the cementitious composites fracture toughness. Scanning electron micrographs were used to characterize the fibres surface before and after the Pull-out tests.

Research on Modifier and Modified Process for Rubber-Particle Used in Rubberized Concrete for Road

2011 ◽  
Vol 243-249 ◽  
pp. 4125-4130 ◽  
Author(s):  
Shuai Tian ◽  
Tong Zhang ◽  
Ye Li
Keyword(s):  
Inorganic Salt ◽  
Rubber Particle ◽  
Volume Ratio ◽  
Alkaline Solutions ◽  
Rubberized Concrete ◽  
Function Mechanism ◽  
Mix Proportion ◽  
Optimum Proportion ◽  
Rubber Particles ◽  
The Impact

This paper studies the optimum proportion of rubber-particles in rubberized concrete for road, tests the impact of 12 modifiers and their modified processes in rubberized concrete and discusses the function mechanism of the modifiers in rubberized concrete. Research indicates: the optimum proportion of rubber-particles in rubberized concrete for road is low mix-proportion (volume ratio<5%); inorganic salt as modifier can markedly enhance the bonding strength between rubber-particles used in road and cement and improve the physical properties of rubberized concrete, among which CaCl2 produces the most effect; but organic solution, acidic or alkaline solutions are not fit to be used as modifiers in rubberized concrete for road.

Durability of concrete containing chloride-based accelerating admixtures

1990 ◽  
Vol 17 (1) ◽  
pp. 102-112
Author(s):  
T. Rezansoff ◽  
D. Stott
Keyword(s):  
Calcium Chloride ◽  
Dynamic Modulus ◽  
Linseed Oil ◽  
Standard Test ◽  
Test Method ◽  
Concrete Durability ◽  
Freezing And Thawing ◽  
Cement Ratio ◽  
Freeze Thaw ◽  
Water To Cement Ratio

The influence of CaCl2 or a chloride-based accelerating admixture on the freeze–thaw resistance of concrete was evaluated. Three air entrained mix designs were investigated using ASTM C666-84, Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing. All mix designs were similar, using cement contents of 340–357 kg/m3 of concrete, except for the addition of either 2% calcium chloride or 2% High Early Pozzolith, while no accelerating admixture was added to the control mix. The entire test program was repeated four times with water-to-cement ratio of 0.46 and three times with the ratio of 0.43. For the Pozzolith-accelerated concrete, half the samples were coated with boiled linseed oil in all seven series. For the control (unaccelerated) concrete, half the samples were coated with boiled linseed oil in one series for each water-to-cement ratio. Performance was monitored using the dynamic modulus of elasticity as obtained from transverse resonant frequency measurements. Weight loss of the specimens was also measured. Only the control samples (no accelerators) showed sufficient durability to satisfy the standard of maintaining at least 60% of the original dynamic modulus after 300 cycles of alternate freezing and thawing. Sealing with linseed oil showed inconsistent improvement in the durability in the various test series when defined in terms of the dynamic modulus; however, weight losses were the lowest of all categories and surface scaling was minimal. Key words: concrete, durability, freeze–thaw testing, calcium chloride, admixtures, sealants, air void system.

scholarly journals Effect of Flyash Addition on Mechanical and Gamma Radiation Shielding Properties of Concrete

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Kanwaldeep Singh ◽  
Sukhpal Singh ◽  
Gurmel Singh
Keyword(s):  
Gamma Radiation ◽  
Attenuation Coefficient ◽  
Cement Content ◽  
Mass Attenuation Coefficient ◽  
Radiation Shielding ◽  
Mechanical Parameters ◽  
Cement Ratio ◽  
Concrete Mixtures ◽  
Water To Cement Ratio ◽  
Shielding Properties

Six concrete mixtures were prepared with 0%, 20%, 30%, 40%, 50%, and 60% of flyash replacing the cement content and having constant water to cement ratio. The testing specimens were casted and their mechanical parameters were tested experimentally in accordance with the Indian standards. Results of mechanical parameters show their improvement with age of the specimens and results of radiation parameters show no significant effect of flyash substitution on mass attenuation coefficient.

Chloride Ingress Control and Promotion of Internal Curing in Concrete Using Superabsorbent Polymer

2021 ◽  
Vol 888 ◽  
pp. 67-75
Author(s):  
Ariel Verzosa Melendres ◽  
Napoleon Solo Dela Cruz ◽  
Araceli Magsino Monsada ◽  
Rolan Pepito Vera Cruz
Keyword(s):  
Compressive Strength ◽  
Cementitious Materials ◽  
Internal Curing ◽  
Mix Design ◽  
Chloride Ingress ◽  
Superabsorbent Polymer ◽  
Cement Slurry ◽  
Chloride Permeability ◽  
Cement Ratio ◽  
Water To Cement Ratio

Chloride ingress into concrete from the surrounding environment can result in the corrosion of the embedded steel reinforcement and cause damage to the concrete. Superabsorbent polymer (SAP) with fine particle size was incorporated into the structure of concrete for controlling the chloride ingress and improving its compressive strength via promotion of internal curing. The SAP used in this study was evaluated for its absorbency property when exposed to cementitious environment such as aqueous solution of Ca (OH)2 and cement slurry. The results were compared to that in sodium chloride solution, the environment where absorbency of most of the SAP found in the market are well studied. Results showed that although SAP absorbency decreased with increasing concentration of Ca (OH)2 and cement, the results suggest that water containing cementitious materials are able to be absorbed by SAP. Chloride ingress into 28-day cured concrete specimens were determined using Rapid Chloride Penetration Test (RCPT) method employing 60V DC driving force. Concrete samples with size of 50 mm height x 100 mm diameter were prepared using a M25 mix design with 0.4 and 0.45 water to cement ratios and different percentages of SAP such as 0.05%, 0.1% and 0.15% with respect to cement mass. Results showed that concrete with 0.15% SAP gave the best result with 14% less chloride permeability than concrete with no SAP for a 0.4 water to cement ratio. Concrete samples for compressive strength tests with size of 200 mm height x 100 mm diameter were prepared using the same mix design and percentages of SAP and cured for 28 days. Results showed that the best results for compressive strength was found at 0.1% SAP at a 0.4 water to cement ratio which can be attributed to internal curing provided by SAP.

Sign in / Sign up

Export Citation Format

Share Document