Study of Egyptian castor biodiesel-diesel fuel properties and diesel engine performance for a wide range of blending ratios and operating conditions for the sake of the optimal blending ratio

2018 ◽  
Vol 174 ◽  
pp. 364-377 ◽  
Author(s):  
Ali M.A. Attia ◽  
Mohamed Nour ◽  
S.A. Nada
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Operating Conditions ◽  
Fuel Properties ◽  
Wide Range ◽  
Optimal Blending

Effects of Alumina Nanoparticles Additives Into Jojoba Methyl Ester-Diesel Mixture on Diesel Engine Performance

2014 ◽  
Author(s):  
Ali M. A. Attia ◽  
Ahmed I. El-Seesy ◽  
Hesham M. El-Batsh ◽  
Mohamed S. Shehata
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Operating Conditions ◽  
Nano Particles ◽  
Alumina Nanoparticles ◽  
Promising Alternative ◽  
Nano Additives ◽  
Conventional Diesel Fuel

Currently, using biofuels to operate diesel engines gets a great attention to the extent that it could replace the limited conventional fossil fuels. These fuels have a closed life cycle (renewable) and they have a remarkable effect on the global greenhouse phenomena. Moreover, the use of non-edible vegetable oils is considered a good choice after a suitable chemical and/or thermal treatment to convert them into esters. The use of jojoba oil shows a promising alternative fuel for conventional diesel fuel even there were unfavorable effects including power reduction. The wide spread usage of nano additives to improve the combustion quality may be a good solution for these problems. This study represents an experimental investigation to examine the effect of nano additives on diesel engine performance at variable operating conditions of load and speed. In this work, alumina nano-particles are added to a mixture of jojoba methyl ester (biodiesel) and conventional diesel fuel at the most recommended value (20% biodiesel and 80% diesel fuel) with different doses from 10 up to 50 mg/l. The received mixture is homogenized with an ultrasonicator mixer. It is found that, the appropriate nano-additives dose corresponding to optimal engine performance is about 30 mg/l. At this dose, the overall BSFC is reduced by about 6%, engine thermal efficiency is increased up to 7%, and all engine emissions have been reduced (NOx about 70%, CO about 75 %, smoke opacity about 5%, and UHC about 55 %) compared with the corresponding values obtained when only a blended fuel of 20% biodiesel is used.

Control-Oriented Model Development and Experimental Validation for a Modern Diesel Engine

2020 ◽  
Author(s):  
Kuo Yang ◽  
Pingen Chen
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Model Development ◽  
Engine Performance ◽  
Operating Conditions ◽  
Least Square ◽  
Injection Timing ◽  
Model Based ◽  
Wide Range ◽  
Mean Square Errors

Abstract Modern Diesel engines have become highly complex multi-input multi-output systems. Controls of modern Diesel engines to meet various requirements such as high fuel efficiency and low NOx and particulate matter (PM) emissions, remain a great challenge for automotive control community. While model-based controls have demonstrated significant potentials in achieving high Diesel engine performance. Complete and high-fidelity control-oriented Diesel engine models are much needed as the foundations of model-based control system development. In this study, a semi-physical, mean-value control-oriented model of a turbocharged Diesel engine equipped with high-pressure exhaust gas recirculation (EGR) and variable geometry turbocharger (VGT) is developed and experimentally validated. The static calibration of Diesel engine model is achieved with the least-square optimization methodology using the experimental test data from a physical Diesel engine platform. The normalized root mean square errors (NRMSEs) of the calibration results are in the range of 0.1095 to 0.2582. The cross-validation results demonstrated that the model was capable of accurately capturing the engine torque output and NOx emissions with the control inputs of EGR, VGT and Start of Injection timing (SOI) in wide-range operating conditions.

Investigation of the Performance of a Diesel Engine Fueled by Biodiesel-Diesel Fuel Mixture With Addition of Nanoparticles

2017 ◽  
Author(s):  
Ahmed I. EL-Seesy ◽  
Ali K. Abdel-Rahman ◽  
Hamdy Hassan ◽  
Shinichi Ookawara ◽  
Meshack Hawi
Keyword(s):  
Diesel Engine ◽  
Dose Level ◽  
Diesel Fuel ◽  
Emission Reduction ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Operating Conditions ◽  
Emission Characteristics ◽  
Engine Test ◽  
Performance And Emission

The current work presents the results of an experimental study that is conducted to investigate the effect of nanoparticles added to biodiesel-diesel fuel mixture. Nano-biodiesel-diesel mixture fuels were prepared by adding of multi-walled carbon nanotubes (MWCNTs). These nanoparticles were blended with biodiesel-diesel fuel in varying mass fractions using an ultrasonic stabilization. A diesel engine test rig was used to examine the effect of nanoparticles on engine performance and emission characteristics with a constant speed of 2500 rpm and different engine loads. The engine test results indicated that the biodiesel-diesel fuel blend slightly decreased the engine performance and increased its emission characteristics at all tested engine operating conditions. The use of nanoparticles was found to improve all engine performance parameters. Specifically, the maximum emission reduction was obtained at a dose level of 20 mg/l, where considerable emission reduction was observed; NOx by 14 %, CO by 30 %, and UHC by 34 %. Also, the best of both engine combustion characteristics and performance were reached at a dose level of 40–50 mg/l. Where the reduction in the brake specific fuel consumption was by 16 %, the increase in both the cylinder peak pressure Pmax, and maximum gross heat release rate dQg/dθmax. were 4 % and 1%, respectively. Finally, the recommended dose level to achieve a significant enhancement in all engine performance is 40 mg/l.

Preparation, Characterization and Engine Performance Characteristics of Used Cooking Sunflower Oil Based Bio-Fuels for a Diesel Engine

2014 ◽  
Vol 984-985 ◽  
pp. 913-923 ◽  
Author(s):  
Sankar Karthikumar ◽  
V. Ragavanandham ◽  
S. Kanagaraj ◽  
R. Manikumar ◽  
A. Asha ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Specific Gravity ◽  
Diesel Fuel ◽  
Sunflower Oil ◽  
Engine Performance ◽  
Fuel Properties ◽  
Performance Characteristics ◽  
Experimental Results ◽  
Single Cylinder ◽  
Blended Fuels

This paper deals on bio-fuel, consisting of used sunflower oil and transesterified - used sunflower oil blended with diesel. They are prepared and tested as a fuel in a direct injection (DI) single cylinder four stroke diesel engine. The main fuel properties of these fuels are measured, the engine performance characteristics are investigated and compared with that of diesel fuel. Fuels are separately prepared, blended and tested for determining the characteristics and combustion in a single cylinder diesel engine. The main fuel properties such as the specific gravity, density, flash and fire points of the blended fuels are measured. The engine performance is investigated and compared with that of diesel fuel. The experimental results showed that the specific gravity of the hybrid bio-fuels is decreased and close to that of diesel fuel. The experimental results also showed that the engine efficiency is closer to the values obtained from the diesel fuel. It is found that among the various blends, transesterifed used sunflower oil with diesel, gives better efficiency. In addition it is found that, the blend of diesel with used sunflower oil gives the lowest fuel consumption as compared to that of other blended fuels. Nomenclatures w1- weight of specific gravity bottle (g) w2- weight of specific gravity bottle + water (g) w3- weight of specific gravity bottle + sample (g)

scholarly journals Performance, Emission and Combustion Characteristics of a Diesel Engine Powered by Macadamia and Grapeseed Biodiesels

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2748 ◽  
Author(s):  
Abul Kalam Azad ◽  
Julian Adhikari ◽  
Pobitra Halder ◽  
Mohammad G. Rasul ◽  
Nur M. S. Hassan ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Combustion Characteristics ◽  
Commercial Application ◽  
Engine Emissions ◽  
Physiochemical Properties ◽  
Brake Thermal Efficiency ◽  
Wide Range ◽  
Minimal Reduction

Biodiesel is an alternative, eco-friendly and renewable source of energy. It can be produced from a wide range of feedstocks which can be grown in marginal land use. It has drawn more attention to the researchers. In this study, the oil extraction, biodiesel conversion, and physiochemical properties of Macadamia (Macadamia integrifolia) and Grapeseed (Vitis vinifera) biodiesels are presented. The experimental investigation of diesel engine performance, emissions and combustion characteristics were conducted using B5 (5% biodiesel and 95% diesel by volume) and B10 (10% biodiesel and 90% diesel by volume) blends. The engine performance parameters, such as brake power (BP), brake specific fuel consumption (BSFC), and brake thermal efficiency (BTE) have been investigated in this experiment. The emission parameters, for example, carbon monoxide (CO), the ratio of CO2/CO, nitrogen oxide (NOx), hydrocarbon (HC), particulate matter (PM) have been measured during the experiment. Finally, the combustion parameters such as cylinder pressure (CP) were recorded, and heat release rate (HRR) was analysed and compared with that of diesel fuel. The study revealed that the Macadamia biodiesel performed better than Grapeseed biodiesel and behaved closely to that of diesel fuel. A significant reduction of engine emissions was found in the case of Macadamia biodiesel with a minimal reduction of engine performance. Further analysis of energy, exergy and tribological characteristics of the Macadamia biodiesel is recommended for assessing its feasibility for commercial application.

scholarly journals Thermal Performance of Compression Ignition Engine Using High Content Biodiesels: A Comparative Study with Diesel Fuel

2021 ◽  
Vol 13 (14) ◽  
pp. 7688
Author(s):  
Asif Afzal ◽  
Manzoore Elahi M. Soudagar ◽  
Ali Belhocine ◽  
Mohammed Kareemullah ◽  
Nazia Hossain ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fatty Acid Content ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Acid Oil ◽  
Exhaust Gas Temperature

In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

scholarly journals CFD Study of Nozzle Configurations for Ultra High Bypass Engines

1993 ◽  
Author(s):  
H. Zimmermann ◽  
R. Gumucio ◽  
K. Katheder ◽  
A. Jula
Keyword(s):  
Engine Performance ◽  
Operating Conditions ◽  
Aerodynamic Design ◽  
Thrust Coefficient ◽  
Optimum Range ◽  
Installation Effects ◽  
Wide Range ◽  
And Performance ◽  
Aircraft Aerodynamics ◽  
Bypass Ratio

Performance and aerodynamic aspects of ultra-high bypass ratio ducted engines have been investigated with an emphasis on nozzle aerodynamics. The interference with aircraft aerodynamics could not be covered. Numerical methods were used for aerodynamic investigations of geometrically different aft end configurations for bypass ratios between 12 and 18, this is the optimum range for long missions which will be important for future civil engine applications. Results are presented for a wide range of operating conditions and effects on engine performance are discussed. The limitations for higher bypass ratios than 12 to 18 do not come from nozzle aerodynamics but from installation effects. It is shown that using CFD and performance calculations an improved aerodynamic design can be achieved. Based on existing correlations, for thrust and mass-flow, or using aerodynamic tailoring by CFD and including performance investigations, it is possible to increase the thrust coefficient up to 1%.

Sign in / Sign up

Export Citation Format

Share Document