Ignition of particles of finely dispersed fuel mixtures based on coal and fine wood

Energy ◽  
2021 ◽  
Vol 220 ◽  
pp. 119697
Author(s):  
G.V. Kuznetsov ◽  
A.V. Zenkov ◽  
A.A. Tolokolnikov ◽  
I.V. Cherednik ◽  
S.A. Yankovsky
Keyword(s):  
Fuel Mixtures ◽  
Fine Wood

Design of an External Combustion Engine and its Application in a Free Piston Compressor

2007 ◽  
Vol 3 ◽  
Author(s):  
Jonathan Hogan Webb
Keyword(s):  
Combustion Engine ◽  
Piston Compressor ◽  
Dead Volume ◽  
Transfer Energy ◽  
Free Piston ◽  
Combustion Gases ◽  
Intermediate Chamber ◽  
Fuel Mixtures ◽  
External Combustion ◽  
External Combustion Engine

The design of a free piston compressor and an analysis on integrating an external combustion engine into the compressor design are presented in this article. A free piston compressor is a device which converts chemical energy to work on a volume of air through the kinetic energy of an inertia driven piston, which is not rigidly attached to a ground. An external combustion engine serves as in intermediate chamber which transfers combustion gases to a device to perform some work. The following discusses the design and experiments on an external combustion engine, with a focus on eliminating an injection holding force on a free piston compressor’s elastomeric membranes. The efficiency of the external combustion engine to transfer energy without significant losses due to heat, dead volume, air/fuel mixtures, and actuated valve speed are also presented.

Pollutant emission from a heat station supplied with agriculture biomass and wood pellet mixture

2012 ◽  
Vol 33 (2) ◽  
pp. 231-242 ◽  
Author(s):  
Marek Juszczak ◽  
Katarzyna Lossy
Keyword(s):  
Carbon Monoxide ◽  
Pollutant Emission ◽  
Heat Output ◽  
Wood Pellets ◽  
Wood Pellet ◽  
Carbon Monoxide Concentration ◽  
Heat Efficiency ◽  
Air Stream ◽  
Fuel Mixtures ◽  
Lower Carbon

Pollutant emission from a heat station supplied with agriculture biomass and wood pellet mixtureTests for combustion of hay and sunflower husk pellets mixed with wood pellets were performed in a horizontal-feed as well as under-feed (retort) wood pellet furnace installed in boilers with a nominal heat output of 15 and 20 kW, located in a heat station. During the combustion a slagging phenomenon was observed in the furnaces. In order to lower the temperature in the furnace, fuel feeding rate was reduced with unaltered air stream rate. The higher the proportion of wood pellets in the mixture the lower carbon monoxide concentration. The following results of carbon monoxide concentration (in mg/m3presented for 10% O2content in flue gas) for different furnaces and fuel mixtures (proportion in wt%) were obtained: horizontal-feed furnace supplied with hay/wood: 0/100 - 326; 30/70 - 157; 50/50 - 301; 100/0 - 3300; horizontal-feed furnace supplied with sunflower husk/wood: 50/50 - 1062; 67/33 - 1721; 100/0 - 3775; under-feed (retort) furnace supplied with hay/wood: 0/100 - 90; 15/85 - 157; 30/70 - 135; 50/50 - 5179; under-feed furnace supplied with sunflower husk/wood: 67/33 - 2498; 100/0 - 3128. Boiler heat output and heat efficiency was low: 7 to 13 kW and about 55%, respectively, for the boiler with horizontal-feed furnace and 9 to 14 kW and 64%, respectively, for the boiler with under-feed furnace.

What Engines Say About Propane Fuel Mixtures

1964 ◽  
Author(s):  
W. E. Adams ◽  
Kenneth Boldt
Keyword(s):  
Fuel Mixtures

scholarly journals Effect of Injection Timing and Injection Duration of Manifold Injected Fuels in Reactivity Controlled Compression Ignition Engine Operated with Renewable Fuels

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4621
Author(s):  
P. A. Harari ◽  
N. R. Banapurmath ◽  
V. S. Yaliwal ◽  
T. M. Yunus Khan ◽  
Irfan Anjum Badruddin ◽  
...  
Keyword(s):  
Nitric Oxide ◽  
Injection Timing ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Compressed Natural Gas ◽  
Reactivity Controlled Compression Ignition ◽  
Brake Thermal Efficiency ◽  
Injection Duration ◽  
Fuel Mixtures

In the current work, an effort is made to study the influence of injection timing (IT) and injection duration (ID) of manifold injected fuels (MIF) in the reactivity controlled compression ignition (RCCI) engine. Compressed natural gas (CNG) and compressed biogas (CBG) are used as the MIF along with diesel and blends of Thevetia Peruviana methyl ester (TPME) are used as the direct injected fuels (DIF). The ITs of the MIF that were studied includes 45°ATDC, 50°ATDC, and 55°ATDC. Also, present study includes impact of various IDs of the MIF such as 3, 6, and 9 ms on RCCI mode of combustion. The complete experimental work is conducted at 75% of rated power. The results show that among the different ITs studied, the D+CNG mixture exhibits higher brake thermal efficiency (BTE), about 29.32% is observed at 50° ATDC IT, which is about 1.77, 3.58, 5.56, 7.51, and 8.54% higher than D+CBG, B20+CNG, B20+CBG, B100+CNG, and B100+CBG fuel combinations. The highest BTE, about 30.25%, is found for the D+CNG fuel combination at 6 ms ID, which is about 1.69, 3.48, 5.32%, 7.24, and 9.16% higher as compared with the D+CBG, B20+CNG, B20+CBG, B100+CNG, and B100+CBG fuel combinations. At all ITs and IDs, higher emissions of nitric oxide (NOx) along with lower emissions of smoke, carbon monoxide (CO), and hydrocarbon (HC) are found for D+CNG mixture as related to other fuel mixtures. At all ITs and IDs, D+CNG gives higher In-cylinder pressure (ICP) and heat release rate (HRR) as compared with other fuel combinations.

scholarly journals Energy Treatment of Solid Municipal Waste in Combination with Biomass by Decentralized Method with the Respect to the Negative Effects on the Environment

2021 ◽  
Vol 13 (8) ◽  
pp. 4405
Author(s):  
Miroslav Rimar ◽  
Olha Kulikova ◽  
Andrii Kulikov ◽  
Marcel Fedak
Keyword(s):  
Heavy Metals ◽  
Municipal Solid Waste ◽  
Solid Waste ◽  
Process Analysis ◽  
Combustion Process ◽  
Municipal Waste ◽  
Negative Effects ◽  
Combustion Properties ◽  
Polycyclic Aromatic ◽  
Fuel Mixtures

Waste is a product of society and one of the biggest challenges for future generations is to understand how to sustainably dispose of large amounts of waste. The main objective of this study was to determine the possibility and conditions of the decentralized combustion of non-hazardous municipal waste. The analysis of the combustion properties of a mixture of wood chips and 20–30% of municipal solid waste showed an improvement in the operating parameters of the combustion process. Analysis also confirmed that the co-combustion of dirty fuels and biomass reduced the risk of releasing minerals and heavy metals from fuel into the natural environment. Approximately 55% of the heavy metals passed into the ash. The analysis of municipal solid waste and fuel mixtures containing municipal solid waste for polycyclic aromatic hydrocarbons showed the risk of increasing polycyclic aromatic hydrocarbon concentrations in flue gases.

scholarly journals Combustion chemistry of methoxymethanol. Part II: Laminar flames of methanol+formaldehyde fuel mixtures

2021 ◽  
pp. 111411
Author(s):  
Alexander A. Konnov ◽  
Elna J.K. Nilsson ◽  
Moah Christensen ◽  
Chong-Wen Zhou
Keyword(s):  
Laminar Flames ◽  
Combustion Chemistry ◽  
Fuel Mixtures

scholarly journals The Influence of Carrier Air Preheating on Autoignition of Inline-Injected Hydrogen–Nitrogen Mixtures in Vitiated Air of High Temperature

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Christoph A. Schmalhofer ◽  
Peter Griebel ◽  
Manfred Aigner
Keyword(s):  
Hydrogen Content ◽  
Gas Turbines ◽  
High Speed ◽  
Flame Stabilization ◽  
Operating Conditions ◽  
Promoting Effect ◽  
Experimental Conditions ◽  
Lean Premixed Combustion ◽  
Image Velocimetry ◽  
Fuel Mixtures

The use of highly reactive hydrogen-rich fuels in lean premixed combustion systems strongly affects the operability of stationary gas turbines (GT) resulting in higher autoignition and flashback risks. The present study investigates the autoignition behavior and ignition kernel evolution of hydrogen–nitrogen fuel mixtures in an inline co-flow injector configuration at relevant reheat combustor operating conditions. High-speed luminosity and particle image velocimetry (PIV) measurements in an optically accessible reheat combustor are employed. Autoignition and flame stabilization limits strongly depend on temperatures of vitiated air and carrier preheating. Higher hydrogen content significantly promotes the formation and development of different types of autoignition kernels: More autoignition kernels evolve with higher hydrogen content showing the promoting effect of equivalence ratio on local ignition events. Autoignition kernels develop downstream a certain distance from the injector, indicating the influence of ignition delay on kernel development. The development of autoignition kernels is linked to the shear layer development derived from global experimental conditions.

scholarly journals Formulation of Surrogate Fuel Mixtures Based on Physical and Chemical Analysis of Hydrodepolymerized Cellulosic Diesel Fuel

2016 ◽  
Vol 30 (9) ◽  
pp. 7331-7341 ◽  
Author(s):  
Dianne J. Luning Prak ◽  
Peter J. Luning Prak ◽  
Paul C. Trulove ◽  
Jim S. Cowart
Keyword(s):  
Chemical Analysis ◽  
Diesel Fuel ◽  
Fuel Mixtures ◽  
Surrogate Fuel ◽  
Physical And Chemical

Ultra-Low Emission Hydrogen/Syngas Combustion With a 1.3 MW Injector Using a Micro-Mixing Lean-Premix System

2011 ◽  
Author(s):  
Brian Hollon ◽  
Erlendur Steinthorsson ◽  
Adel Mansour ◽  
Vincent McDonell ◽  
Howard Lee
Keyword(s):  
Carbon Dioxide ◽  
Natural Gas ◽  
Flame Temperature ◽  
Fuel Mixture ◽  
Full Scale ◽  
Operating Conditions ◽  
Nox Emissions ◽  
Fuel Injector ◽  
Nitrogen Dilution ◽  
Fuel Mixtures

This paper discusses the development and testing of a full-scale micro-mixing lean-premix injector for hydrogen and syngas fuels that demonstrated ultra-low emissions and stable operation without flashback for high-hydrogen fuels at representative full-scale operating conditions. The injector was fabricated using Macrolamination technology, which is a process by which injectors are manufactured from bonded layers. The injector utilizes sixteen micro-mixing cups for effective and rapid mixing of fuel and air in a compact package. The full scale injector is rated at 1.3 MWth when operating on natural gas at 12.4 bar (180 psi) combustor pressure. The injector operated without flash back on fuel mixtures ranging from 100% natural gas to 100% hydrogen and emissions were shown to be insensitive to operating pressure. Ultra-low NOx emissions of 3 ppm were achieved at a flame temperature of 1750 K (2690 °F) using a fuel mixture containing 50% hydrogen and 50% natural gas by volume with 40% nitrogen dilution added to the fuel stream. NOx emissions of 1.5 ppm were demonstrated at a flame temperature over 1680 K (2564 °F) using the same fuel mixture with only 10% nitrogen dilution, and NOx emissions of 3.5 ppm were demonstrated at a flame temperature of 1730 K (2650 °F) with only 10% carbon dioxide dilution. Finally, using 100% hydrogen with 30% carbon dioxide dilution, 3.6 ppm NOx emissions were demonstrated at a flame temperature over 1600 K (2420 °F). Superior operability was achieved with the injector operating at temperatures below 1470 K (2186 °F) on a fuel mixture containing 87% hydrogen and 13% natural gas. The tests validated the micro-mixing fuel injector technology and the injectors show great promise for use in future gas turbine engines operating on hydrogen, syngas or other fuel mixtures of various compositions.

Sign in / Sign up

Export Citation Format

Share Document