The manufacture, mechanical properties, and microstructural analysis of synthetic quartz-cemented sandstones

2021 ◽  
Vol 146 ◽  
pp. 104869
Author(s):  
E. Rice-Birchall ◽  
D.R. Faulkner ◽  
J.D. Bedford
Keyword(s):  
Mechanical Properties ◽  
Microstructural Analysis ◽  
Synthetic Quartz

An analysis of the transport properties and mechanical stability of rapidly solidified Al-Sb alloy

2015 ◽  
Vol 10 (2) ◽  
pp. 2663-2681
Author(s):  
Rizk El- Sayed ◽  
Mustafa Kamal ◽  
Abu-Bakr El-Bediwi ◽  
Qutaiba Rasheed Solaiman
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Melt Spinning ◽  
Elastic Moduli ◽  
Mechanical Stability ◽  
Microstructural Analysis ◽  
Alloy System ◽  
Antimony Content ◽  
The Stability ◽  
Rapidly Solidified

The structure of a series of AlSb alloys prepared by melt spinning have been studied in the as melt–spun ribbons  as a function of antimony content .The stability  of these structures has  been  related to that of the transport and mechanical properties of the alloy ribbons. Microstructural analysis was performed and it was found that only Al and AlSb phases formed for different composition.  The electrical, thermal and the stability of the mechanical properties are related indirectly through the influence of the antimony content. The results are interpreted in terms of the phase change occurring to alloy system. Electrical resistivity, thermal conductivity, elastic moduli and the values of microhardness are found to be more sensitive than the internal friction to the phase changes. 

scholarly journals Influence of Hydrostatic Extrusion on the Mechanical Properties of the Model Al-Mg Alloys

2021 ◽  
Author(s):  
Aleksandra Towarek ◽  
Wojciech Jurczak ◽  
Joanna Zdunek ◽  
Mariusz Kulczyk ◽  
Jarosław Mizera
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Tensile Strength ◽  
Microstructural Analysis ◽  
Tensile Tests ◽  
Hydrostatic Extrusion ◽  
Microstructure Formation ◽  
Initial State ◽  
Degree Of Deformation ◽  
Al Mg Alloys

AbstractTwo model aluminium-magnesium alloys, containing 3 and 7.5 wt.% of Mg, were subjected to plastic deformation by means of hydrostatic extrusion (HE). Two degrees of deformation were imposed by two subsequent reductions of the diameter. Microstructural analysis and tensile tests of the materials in the initial state and after deformation were performed. For both materials, HE extrusion resulted in the deformation of the microstructure—formation of the un-equilibrium grain boundaries and partition of the grains. What is more, HE resulted in a significant increase of tensile strength and decrease of the elongation, mostly after the first degree of deformation.

scholarly journals Enhancement of Mechanical Properties and Porosity of Concrete Using Steel Slag Coarse Aggregate

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2865
Author(s):  
Md Jihad Miah ◽  
Md. Munir Hossain Patoary ◽  
Suvash Chandra Paul ◽  
Adewumi John Babafemi ◽  
Biranchi Panda
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Microstructural Analysis ◽  
Steel Slag ◽  
Physical And Mechanical Properties ◽  
Length Change ◽  
Sustainable Building ◽  
Burnt Clay ◽  
Lower Porosity ◽  
Furnace Steel

This paper investigates the possibility of utilizing steel slags produced in the steelmaking industry as an alternative to burnt clay brick aggregate (BA) in concrete. Within this context, physical, mechanical (i.e., compressive and splitting tensile strength), length change, and durability (porosity) tests were conducted on concrete made with nine different percentage replacements (0%, 10%, 20%, 30%, 40%, 50%, 60%, 80%, and 100% by volume of BA) of BA by induction of furnace steel slag aggregate (SSA). In addition, the chemical composition of aggregate through X-ray fluorescence (XRF) analysis and microstructural analysis through scanning electron microscopy (SEM) of aggregates and concrete were performed. The experimental results show that the physical and mechanical properties of concrete made with SSA were significantly higher than that of concrete made with BA. The compressive and tensile strength increased by 73% when SSA fully replaced BA. The expansion of concrete made with SSA was a bit higher than the concrete made with BA. Furthermore, a significant lower porosity was observed for concrete made with SSA than BA, which decreased by 40% for 100% SSA concrete than 100% BA concrete. The relation between compressive and tensile strength with the porosity of concrete mixes are in agreement with the relationships presented in the literature. This study demonstrates that SSA can be used as a full replacement of BA, which is economical, conserves the natural aggregate, and is sustainable building material since burning brick produces a lot of CO2.

Subsurface microstructural analysis and mechanical properties of pearlitic rail steels in service

Wear ◽  
2013 ◽  
Vol 302 (1-2) ◽  
pp. 1453-1460 ◽  
Author(s):  
F.A.M. Alwahdi ◽  
A. Kapoor ◽  
F.J. Franklin
Keyword(s):  
Mechanical Properties ◽  
Microstructural Analysis

Effect of Tin Oxide Coatings by Spray Pyrolysis Process on Mechanical Properties of Aluminium, Brass and Mild Steel

2021 ◽  
Vol 13 (2) ◽  
Author(s):  
M. Shunmugasundaram ◽  
A. Praveenkumar ◽  
L. Ponraj Sankar ◽  
S. Sivasankar
Keyword(s):  
Mechanical Properties ◽  
Mild Steel ◽  
Substrate Temperature ◽  
Spray Pyrolysis ◽  
Tin Oxide ◽  
Microstructural Analysis ◽  
Solution Concentration ◽  
Solution Flow Rate ◽  
Spray Pyrolysis Method ◽  
Solution Flow

Mechanical properties of materials are enhanced by different methods to increase the usage of the materials. In this research spray pyrolysis method is employed to increase the mechanical characteristics of three different materials. The tin oxide is chosen as coated material and aluminium, brass, mild steel are selected as substrate materials. The 500nm thin film is developed over the substrate materials by spray pyrolysis. The substrate temperature are chosen as 300? C for aluminium, 400? C for brass and mildsteel. Nozzle to substrate distance is 0.4 m, substrate temperature is 300? C for aluminium and 400? C for solution concentration as 0.2 mole and solution flow rate is 1ml/min are selected for constant deposition parameters. The hardness and tensile strength result clearly shows that strength is increased by adding the coating over the surface. The material is heated above crystallization temperature and SnO2 increases the tensile and hardness strength of the materials. The triangular metrological microscope is used to examine the microstructure of non coated and coated substrate materials. The microstructural analysis is showed that the uncoated surface of the substrate material is full of rough and pores. And displays that the tin oxide coated surface of the substrates after the initial deposition disclosed a surface with a agglomeration of tin oxide in homogeneous and uniform than the uncoated substrates.

Manuscript Title: Mechanical and Microstructural Studies of Volcanic Ash Beds in Unconventional Reservoirs

2021 ◽  
Author(s):  
Juan C Acosta ◽  
Mark E Curtis ◽  
Carl H Sondergeld ◽  
Chandra S Rai
Keyword(s):  
Mechanical Properties ◽  
Hydraulic Fracturing ◽  
Young’S Modulus ◽  
Volcanic Ash ◽  
Young's Modulus ◽  
Microstructural Analysis ◽  
Thin Layers ◽  
Ion Milling ◽  
Eagle Ford ◽  
Diagenetic Alteration

Abstract Volcanic ash beds are thin layers commonly observed in the Eagle Ford, Niobrara and, Vaca Muerta formations. Because of their differences in composition, sedimentary structures, and diagenetic alteration, they exhibit a significant contrast in mechanical properties with respect to surrounding formation layers. This can impact hydraulic fracturing, affecting fracture propagation and fracture geometry. Quantifying the mechanical properties of ash beds becomes significant; however, it is a challenge with traditional testing methods. Common logging fails to identify the ash beds, and core plug testing is not possible because of their friability. In this study, nanoindentation was used to measure the mechanical properties (Young's modulus, creep, and anisotropy) in Eagle Ford ash beds, and to determine the contrast with the formation matrix properties. Two separate ash beds of high clay and plagioclase composition were epoxied in an aluminum tray and left for 48 hours curing time. Horizontal and vertical samples of ash beds were acquired and mounted on a metal stub, followed by polishing and broad beam ion milling. Adjacent samples were also prepared for high-resolution Scanning Electron Microscope (SEM) microstructural analysis. The Young's modulus in ash beds ranged from 12 to 24 GPa, with the horizontal direction Young's modulus being slightly greater than that of the vertical samples. The Young's modulus contrast with adjacent layers was calculated to be 1:2 with clay-rich zones and 1:4 with calcite rich zones. The creep deformation rate was three times higher for ash beds compared to other zones. Using Backus averaging, it was determined that the presence of ash beds can increase the anisotropy in the formation by 15-25%. SEM results showed a variation in microstructure between the ash beds with evidence of diagenetic conversion of rhyolitic material into clays. Key differences between the two ash beds were due to the presence of plagioclase and the occurrence of porosity within kaolinite. Overall porosity varied between the two ash beds and adjacent carbonate layers showing a significant increase in porosity. Understanding the moduli contrast between adjacent layers can improve the hydraulic fracturing design when ash beds are encountered. In addition, the presence of these beds can lead to proppant embedment and loss in fracture connectivity. These results can be used for improving geomechanical models.

scholarly journals Effect of Graphene Nanosheets Content on Microstructure and Mechanical Properties of Titanium Matrix Composite Produced by Cold Pressing and Sintering

Nanomaterials ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 1024 ◽  
Author(s):  
Milad Haghighi ◽  
Mohammad Shaeri ◽  
Arman Sedghi ◽  
Faramarz Djavanroodi
Keyword(s):  
Mechanical Properties ◽  
Matrix Composite ◽  
Volume Fraction ◽  
Graphene Nanosheets ◽  
Microstructural Analysis ◽  
Titanium Matrix ◽  
Titanium Matrix Composite ◽  
Cold Pressing ◽  
Sintering Time ◽  
Microstructure And Mechanical Properties

The effect of graphene nanosheet (GNS) reinforcement on the microstructure and mechanical properties of the titanium matrix composite has been discussed. For this purpose, composites with various GNS contents were prepared by cold pressing and sintering at various time periods. Density calculation by Archimedes’ principle revealed that Ti/GNSs composites with reasonable high density (more than 99.5% of theoretical density) were produced after sintering for 5 h. Microstructural analysis by X-ray diffraction (XRD) and a field emission scanning electron microscope (FESEM) showed that TiC particles were formed in the matrix during the sintering process as a result of a titanium reaction with carbon. Higher GNS content as well as sintering time resulted in an increase in TiC particle size and volume fraction. Microhardness and shear punch tests demonstrated considerable improvement of the specimens’ mechanical properties with the increment of sintering time and GNS content up to 1 wt. %. The microhardness and shear strength of 1 wt. % GNS composites were enhanced from 316 HV and 610 MPa to 613 HV and 754 MPa, respectively, when composites sintered for 5 h. It is worth mentioning that the formation of the agglomerates of unreacted GNSs in 1.5 wt. % GNS composites resulted in a dramatic decrease in mechanical properties.

Influence of Continuous Annealing Conditions on the Microstructure and Mechanical Properties of a C-Mn Dual Phase Steel

2010 ◽  
Vol 638-642 ◽  
pp. 3479-3484 ◽  
Author(s):  
Roberta O. Rocha ◽  
Tulio M.F. Melo ◽  
Dagoberto Brandao Santos
Keyword(s):  
Mechanical Properties ◽  
Microstructural Analysis ◽  
Tensile Tests ◽  
Recrystallization Temperature ◽  
Continuous Annealing ◽  
Dual Phase ◽  
Heating Rates ◽  
Microstructure And Mechanical Properties ◽  
Annealing Cycle ◽  
Soaking Temperature

The influence of continuous annealing variables on the microstructure and mechanical properties of a C-Mn Dual Phase (DP) steel was studied. The annealing cycles were simulated using a Gleeble machine. Some specimens were quenched at different stages of the annealing cycle in order to evaluate the microstructural evolution during the annealing process. Tensile tests and microstrutural analysis were carried out. The results showed that high heating rates increased the final recrystallization temperature and as a consequence the microstructure obtained was refined. Austenite grain nucleation and growth were also influenced by the heating rates. Soaking temperature was the most influent variable on the mechanical properties, i. e., the yield strength increased and the tensile strength decreased with an increase in the soaking temperature. Microstructural analysis showed that not only martensite, but also bainite and martensite-retained autenite constituent (MA) were formed. Undissolved carbides were also detected by transmission electron microscopy.

scholarly journals Twisting of the Tail Rotor Shaft - A Case Study

2018 ◽  
Vol 778 ◽  
pp. 28-32
Author(s):  
Muhammad Shahzad ◽  
Tanveer Manzoor ◽  
Qanita Tayyaba ◽  
Ammad Hussain Qureshi
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
High Strain ◽  
Microstructural Analysis ◽  
Sem Images ◽  
Rotor Shaft ◽  
Ansys Simulation ◽  
Strain Rate Loading ◽  
Rule Out

Presented results report the findings of a case study carried out to determine the possible factors that lead to the twisting of tail rotor shaft. The structural materials of the shaft was evaluated in terms of microstructural analysis and mechanical properties to rule out any material fault. The SEM images showed that the localized fractures at twist ends occurred without any significant plastic deformation. Moreover, there was no evidence of fatigue. Such behavior suggests that twist occurred under impact / high strain rate loading. Such loading conditions are not possible during the event to ground hitting. The Ansys simulation confirmed that the observed twisting can increase the stress at localized point in excess of UTS and cause fracture.

Sign in / Sign up

Export Citation Format

Share Document