scholarly journals New approach for regulation of the internal recirculation flow rate by fuzzy logic in biological wastewater treatments

2021 ◽  
Author(s):  
I. Santín ◽  
R. Vilanova ◽  
C. Pedret ◽  
M. Barbu
Keyword(s):  
Fuzzy Logic ◽  
Flow Rate ◽  
New Approach ◽  
Recirculation Flow

scholarly journals Chemical–Electrochemical Process Concept for Lead Recovery from Waste Cathode Ray Tube Glass

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1546
Author(s):  
Árpád Imre-Lucaci ◽  
Melinda Fogarasi ◽  
Florica Imre-Lucaci ◽  
Szabolcs Fogarasi
Keyword(s):  
Flow Rate ◽  
Current Density ◽  
Complete Recovery ◽  
Electrochemical Process ◽  
Operating Conditions ◽  
General Effect ◽  
Optimal Operating ◽  
Recirculation Flow ◽  
Lead Recovery ◽  
Cathode Ray Tube

This paper presents a novel approach for the recovery of lead from waste cathode-ray tube (CRT) glass by applying a combined chemical-electrochemical process which allows the simultaneous recovery of Pb from waste CRT glass and electrochemical regeneration of the leaching agent. The optimal operating conditions were identified based on the influence of leaching agent concentration, recirculation flow rate and current density on the main technical performance indicators. The experimental results demonstrate that the process is the most efficient at 0.6 M acetic acid concentration, flow rate of 45 mL/min and current density of 4 mA/cm2. The mass balance data corresponding to the recycling of 10 kg/h waste CRT glass in the identified optimal operating conditions was used for the environmental assessment of the process. The General Effect Indices (GEIs), obtained through the Biwer Heinzle method for the input and output streams of the process, indicate that the developed recovery process not only achieve a complete recovery of lead but it is eco-friendly as well.

Photo-degradation of butyl parahydroxybenzoate by using TiO2-supported catalyst

2013 ◽  
Vol 67 (10) ◽  
pp. 2141-2147 ◽  
Author(s):  
Patrick Atheba ◽  
Patrick Drogui ◽  
Brahima Seyhi ◽  
Didier Robert
Keyword(s):  
Flow Rate ◽  
Photocatalytic Oxidation ◽  
Supported Catalyst ◽  
Operating Conditions ◽  
Treatment Efficiency ◽  
Optimal Operating ◽  
Photo Degradation ◽  
Photochemical Process ◽  
Recirculation Flow ◽  
High Treatment

The present work evaluates the potential of the photocatalysis (PC) process for the degradation of butylparaben (BPB). Relatively high treatment efficiency was achieved by comparison to photochemical process. Prior to photocatalytic degradation, adsorption (AD) of BPB occurred on the titanium dioxide (TiO2)-supported catalyst. AD was described by Langmuir isotherm (KL = 0.085 L g−1, qm = 4.77 mg g−1). The influence of angle of inclination of the reactor, pH, recirculation flow rate and initial concentration of BPB were investigated. The PC process applied under optimal operating conditions (recirculation flow rate of 0.15 L min−1, angle of inclination of 15°, pH = 7 and 5 mg L−1 of BPB) is able to oxidize 84.9–96.6% of BPB and to ensure around 38.7% of mineralization. The Langmuir–Hinshelwood kinetic model described well the photocatalytic oxidation of BPB (k = 7.02 mg L−1 h−1, K = 0.364 L mg−1).

New approach to maintaining liquid flow rate stability in national primary standard

2021 ◽  
pp. 101930
Author(s):  
N.I. Mikheev ◽  
V.M. Molochnikov ◽  
D.V. Kratirov ◽  
O.A. Dushina ◽  
A.A. Paereliy ◽  
...  
Keyword(s):  
Flow Rate ◽  
Liquid Flow ◽  
Liquid Flow Rate ◽  
Primary Standard ◽  
New Approach ◽  
National Primary Standard

Effect of Recirculation Device With Counter Swirl Vane on Performance of High Pressure Ratio Centrifugal Compressor

2011 ◽  
Author(s):  
Hideaki Tamaki
Keyword(s):  
High Pressure ◽  
Mach Number ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Negative Slope ◽  
Tip Leakage Flow ◽  
Recirculation Flow ◽  
Operating Range ◽  
High Pressure Ratio

Centrifugal compressors used for turbochargers need to achieve a wide operating range. The author has developed a high pressure ratio centrifugal compressor with pressure ratio 5.7 for a marine use turbocharger. In order to enhance operating range, two different types of recirculation devices were applied. One is a conventional recirculation device. The other is a new one. The conventional recirculation device consists of an upstream slot, bleed slot and the annular cavity which connects both slots. The new recirculation device has vanes installed in the cavity. These vanes were designed to provide recirculation flow with negative preswirl at the impeller inlet, a swirl counterwise to the impeller rotational direction. The benefits of the application of both of the recirculation devices were ensured. The new device in particular, shifted surge line to a lower flow rate compared to the conventional device. This paper discusses how the new recirculation device affects the flow field in the above transonic centrifugal compressor by using steady 3-D calculations. Since the conventional recirculation device injects the flow with positive preswirl at the impeller inlet, the major difference between the conventional and new recirculation device is the direction of preswirl that the recirculation flow brings to the impeller inlet. This study focuses on two effects which preswirl of the recirculation flow will generate. (1) Additional work transfer from impeller to fluid. (2) Increase or decrease of relative Mach number. Negative preswirl increases work transfer from the impeller to fluid as the flow rate reduces. It increases negative slope on pressure ratio characteristics. Hence the recirculation flow with negative preswirl will contribute to stability of the compressor. Negative preswirl also increases the relative Mach number at the impeller inlet. It moves shock downstream compared to the conventional recirculation device. It leads to the suppression of the extension of blockage due to the interaction of shock with tip leakage flow.

Determination of Safe Pumping Temperature for Waxy Crude Pipelines

2006 ◽  
Author(s):  
Jinjun Zhang ◽  
Jianlin Ding ◽  
Kang Xu ◽  
Huajun Fan
Keyword(s):  
Flow Rate ◽  
Pour Point ◽  
Heating Temperature ◽  
Safety Margin ◽  
Low Flow ◽  
Stable Operation ◽  
Inlet Temperature ◽  
New Approach ◽  
Point Temperature ◽  
Waxy Crude

Flow risk of a hot waxy crude pipeline mainly comes from restart failure, i.e. oil gelation resulted from prolonged pipeline shutdown, and unstable operation at low flow rate. Once the unstable operation happens, the friction loss of the pipeline increases with decreasing flow rate and finally flow may cease if treated improperly. To avoid these flow risks, the pumping temperature of the crude is generally required to be kept above a minimum allowable temperature, and conventionally the pour point temperature is taken. This practice is effective but quite rough. Obviously, to control the inlet temperature of a heating station at the pour point temperature implies different safety margin for winter and summer operation. For large throughput hot oil pipelines, reduction of the heating temperature even by a little bit may save a great amount of fuel. Therefore, how to save fuel while ensuring safe operation has been a valuable topic for long time. On the other hand, many factors impacting the flow safety are stochastic and with uncertainty, so analysis without considering this feature can hardly yield convincible results, though this has been the common case for many years. In this paper, by taking the stochastic feature into account, a Stable Operation Index (SOI) and a Pipeline Restartability Index (PRI) were proposed to assess the flow safety of a pipeline concerning the low-flowrate stable operation and restartability after shutdown. Combining these two indexes, a Pipeline Flow Safety Index (PFSI) was adopted to assess the flow risks of hot waxy crude pipelines. On this basis a new approach to quantitatively determining the safe pumping temperature was developed and illustrated by a case study. Encouraging results show that this new approach has the potential to replace the simple rule of pour point as a guide to determining the safe pumping temperature of waxy crude pipelines.

scholarly journals A Systematic Study of Ammonia Recovery from Anaerobic Digestate Using Membrane-Based Separation

Membranes ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 19
Author(s):  
Fanny Rivera ◽  
Raúl Muñoz ◽  
Pedro Prádanos ◽  
Antonio Hernández ◽  
Laura Palacio
Keyword(s):  
Flow Rate ◽  
Membrane Surface ◽  
H2so4 Solution ◽  
Membrane Area ◽  
Recirculation Flow ◽  
Force Microscopy ◽  
Reservoir Volume ◽  
Atomic Force ◽  
Flat Sheet ◽  
Ammonia Recovery

Ammonia recovery from synthetic and real anaerobic digestates was accomplished using hydrophobic flat sheet membranes operated with H2SO4 solutions to convert ammonia into ammonium sulphate. The influence of the membrane material, flow rate (0.007, 0.015, 0.030 and 0.045 m3 h−1) and pH (7.6, 8.9, 10 and 11) of the digestate on ammonia recovery was investigated. The process was carried out with a flat sheet configuration at a temperature of 35 °C and with a 1 M, or 0.005 M, H2SO4 solution on the other side of the membrane. Polytetrafluoroethylene membranes with a nominal pore radius of 0.22 µm provided ammonia recoveries from synthetic and real digestates of 84.6% ± 1.0% and 71.6% ± 0.3%, respectively, for a membrane area of 8.6 × 10−4 m2 and a reservoir volume of 0.5 L, in 3.5 h with a 1 M H2SO4 solution and a recirculation flow on the feed side of the membrane of 0.030 m3 h−1. NH3 recovery followed first order kinetics and was faster at higher pHs of the H2SO4 solution and recirculation flow rate on the membrane feed side. Fouling resulted in changes in membrane surface morphology and pore size, which were confirmed by Atomic Force Microscopy and Air Displacement Porometry.

scholarly journals A Fuzzy Logic Model for Power Transformer Faults’ Severity Determination Based on Gas Level, Gas Rate, and Dissolved Gas Analysis Interpretation

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 1009 ◽  
Author(s):  
Rahman Azis Prasojo ◽  
Harry Gumilang ◽  
Suwarno ◽  
Nur Ulfa Maulidevi ◽  
Bambang Anggoro Soedjarno
Keyword(s):  
Fuzzy Logic ◽  
Power Transformer ◽  
Local Population ◽  
Gas Analysis ◽  
Power Transformers ◽  
Support Vector ◽  
Dissolved Gas ◽  
New Approach ◽  
Dissolved Gas Analysis ◽  
Novel Approach

In determining the severity of power transformer faults, several approaches have been previously proposed; however, most published studies do not accommodate gas level, gas rate, and Dissolved Gas Analysis (DGA) interpretation in a single approach. To increase the reliability of the faults’ severity assessment of power transformers, a novel approach in the form of fuzzy logic has been proposed as a new solution to determine faults’ severity using the combination of gas level, gas rate, and DGA interpretation from the Duval Pentagon Method (DPM). A four-level typical concentration and rate were established based on the local population. To simplify the assessment of hundreds of power transformer data, a Support Vector Machine (SVM)-based DPM with high agreements to the graphical DPM has been developed. The proposed approach has been implemented to 448 power transformers and further implementation was done to evaluate faults’ severity of power transformers from historical DGA data. This new approach yields in high agreement with the previous methods, but with better sensitivity due to the incorporation of gas level, gas rate, and DGA interpretation results in one approach.

Sign in / Sign up

Export Citation Format

Share Document