scholarly journals Evaluation of post-liquefaction volumetric strain of reconstituted samples based on soil compressibility

2021 ◽  
Author(s):  
Jongkwan Kim ◽  
Motoki Kazama ◽  
Tadashi Kawai
Keyword(s):  
Volumetric Strain ◽  
Soil Compressibility

Susceptibility to Compaction, Load Support Capacity, and Soil Compressibility of Hapludox

2004 ◽  
Vol 68 (1) ◽  
pp. 17 ◽  
Author(s):  
Silvia Imhoff ◽  
Alvaro Pires Da Silva ◽  
David Fallow
Keyword(s):  
Soil Compressibility

scholarly journals Study of Influence of Width to Thickness Ratio in Sheet Metals on Bendability under Ambient and Superimposed Hydrostatic Pressure

2021 ◽  
Vol 2 (3) ◽  
pp. 542-558
Author(s):  
Mohammadmehdi Shahzamanian ◽  
David Lloyd ◽  
Amir Partovi ◽  
Peidong Wu
Keyword(s):  
Hydrostatic Pressure ◽  
Stress Ratio ◽  
Fracture Strain ◽  
Stress Triaxiality ◽  
Volumetric Strain ◽  
Thickness Ratio ◽  
Sheet Metals ◽  
The Finite Element Method ◽  
Bending Strain ◽  
Good Agreement

The effect of the width to thickness ratio on the bendability of sheet metal is investigated using the finite element method (FEM) employing the Gurson–Tvergaard–Needleman (GTN) model. Strain path changes in the sheet with change in the width/thickness ratio. It is shown that bendability and fracture strain increase significantly by decrease in the width/thickness ratio. The stress state is almost uniaxial when the stress ratio (α) is close to zero for narrow sheets. Stress ratio is nothing but the major stress to minor stress ratio. This delays the growth and coalescence of micro-voids as the volumetric strain and stress triaxiality (pressure/effective stress) decrease. On the other hand, ductility decreases with increase in α for wider sheets. Fracture bending strain is calculated and, as expected, it increases with decrease in the width/thickness ratio. Furthermore, a brief study is performed to understand the effect of superimposed hydrostatic pressure on fracture strain for various sheet metals with different width/thickness ratios. It is found that the superimposed hydrostatic pressure increases the ductility, and that the effect of the width/thickness ratio in metals on ductility is as significant as the effect of superimposed hydrostatic pressure. Numerical results are found to be in good agreement with experimental observations.

Mechanical behaviour of powders using a medium pressure flexible boundary cubical triaxial tester

2003 ◽  
Vol 217 (3) ◽  
pp. 233-241 ◽  
Author(s):  
F Li ◽  
V M Puri
Keyword(s):  
Shear Modulus ◽  
Mechanical Behaviour ◽  
Triaxial Compression ◽  
Three Dimensional ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Alumina Powder ◽  
Medium Pressure ◽  
Mean Pressure ◽  
Confining Pressures

A medium pressure (<21 MPa) flexible boundary cubical triaxial tester was designed to measure the true three-dimensional response of powders. In this study, compression behaviour and strength of a microcrystalline cellulose powder (Avicel® PH102), a spray-dried alumina powder (A16SG), and a fluid-bed-granulated silicon nitride based powder (KY3500) were measured. To characterize the mechanical behaviour, three types of triaxial stress paths, that is, the hydrostatic triaxial compression (HTC), the conventional triaxial compression (CTC), and the constant mean pressure triaxial compression (CMPTC) tests were performed. The HTC test measured the volumetric response of the test powders under isostatic pressure from 0 to 13.79MPa, during which the three powders underwent a maximum volumetric strain of 40.8 per cent for Avicel® PH102, 30.5 per cent for A16SG, and 33.0 per cent for KY3500. The bulk modulus values increased 6.4-fold from 57 to 367MPa for Avicel® PH102, 3.7-fold from 174 to 637 MPa for A16SG, and 8.1-fold from 74 to 597MPa for KY3500, when the isotropic stress increased from 0.69 to 13.79 MPa. The CTC and CMPTC tests measured the shear response of the three powders. From 0.035 to 3.45MPa confining pressure, the shear modulus increased 28.7-fold from 1.6 to 45.9MPa for Avicel® PH102, 35-fold from 1.7 to 60.5MPa for A16SG, and 28.5-fold from 1.5 to 42.8MPa for KY3500. In addition, the failure stresses of the three powders increased from 0.129 to 4.41 MPa for Avicel® PH102, 0.082 to 3.62 MPa for A16SG, and 0.090 to 4.66MPa for KY3500, respectively, when consolidation pressure increased from 0.035 to 3.45MPa. In addition, the shear modulus and failure stress values determined from the CTC test at 2.07, 2.76, and 3.45MPa confining pressures are consistently greater than those from the CMPTC test at the same constant mean pressures. This observation demonstrates the influence of stress paths on material properties. The CTT is a useful tool for characterizing the three-dimensional response of powders and powder mixtures.

Insights into the velocity-dependent geometry and internal strain in accretionary wedges from analogue models

2017 ◽  
Vol 155 (5) ◽  
pp. 1089-1104 ◽  
Author(s):  
BIN DENG ◽  
LEI JIANG ◽  
GAOPING ZHAO ◽  
RUI HUANG ◽  
YUANBO WANG ◽  
...  
Keyword(s):  
Brittle Material ◽  
High Velocity ◽  
Frontal Zone ◽  
Volumetric Strain ◽  
Velocity Dependence ◽  
Shortening Velocity ◽  
Asymmetric Structures ◽  
Analogue Models ◽  
Velocity Of Shortening ◽  
Geometry And Kinematics

AbstractAlthough the brittle material in analogue models is characterized by a linear Navier-Coulomb behaviour and rate-independent deformation, the geometry and style of deformation in accretionary wedges is sensitive to shortening velocity. In this study we have constructed a series of analogue models with various shortening velocities in order to study the influence of shortening velocity on the geometry and kinematics of accretionary wedges. Model results illustrate how shortening velocity has an important influence on the geometry and kinematics of the resulting wedge. In general, for models having similar bulk shortening, the accretionary wedges with higher velocities of shortening are roughly steeper, higher and longer, as well as having larger critical wedge angles and height. It accommodates a number of foreland-vergent thrusts, larger fault spacing and displacement rates than those of low- to medium-velocity shortening, which indicates a weak velocity-dependence in geometry of the wedge. Moreover, models with a high velocity of shortening undergo larger amounts of volumetric strain and total layer-parallel shortening than models with low- to medium-velocity shortening. The former accommodate a greater development of back thrusts and asymmetric structures; a backwards-to-forwards style of wedge growth therefore occurs in the frontal zone under high-velocity shortening.

An exact anelastic model for the free-surface relfection of P and S-I waves

1989 ◽  
Vol 79 (3) ◽  
pp. 842-859
Author(s):  
R. D. Borcherdt ◽  
G. Glassmoyer
Keyword(s):  
Free Surface ◽  
Volumetric Strain ◽  
Major Axis ◽  
P Wave ◽  
Reflection Coefficients ◽  
S Wave ◽  
Low Loss ◽  
Surface Reflection ◽  
Pierre Shale ◽  
Homogeneous Wave

Abstract Exact anelastic solutions incorporating inhomogeneous waves are used to model numerically S-I and P waves incident on the free surface of a low-loss anelastic half-space. Anelastic free-surface reflection coefficients are computed for the volumetric strain and displacement components of inhomogeneous wave fields. For the problem of an incident homogeneous S-I wave in Pierre shale, the largest strain and displacement amplitudes for the reflected P wave occur at angles of incidence for which the particle motion for the reflected inhomogeneous P wave is elliptical (minor/major axis = 0.6), the specific absorption (QP−1) is greater (300 per cent) and the velocity is less (25 per cent) than those for a corresponding homogeneous P wave, the direction of phase propagation is not parallel to the free surface, and the amplitude of the wave shows a significant increase with depth (6 per cent in one wavelength). Energy reflection coefficients computed for this low-loss anelastic model show that energy flow due to interaction of the incident and reflected waves reach maxima (30 per cent of the incident energy) near large but nongrazing angles of incidence. For the problem of an incident homogeneous P wave in Pierre shale, the inhomogeneity of the reflected S wave is shown not to contribute to significant variations in wave field characteristics over those that would be expected for a homogeneous wave.

Experimental investigation of the effect of compliant pores on reservoir rocks under hydrostatic and triaxial compression stress states

2019 ◽  
Vol 56 (7) ◽  
pp. 983-991
Author(s):  
Hua Yu ◽  
Kam Ng ◽  
Dario Grana ◽  
John Kaszuba ◽  
Vladimir Alvarado ◽  
...  
Keyword(s):  
Pore Pressure ◽  
Triaxial Compression ◽  
Matrix Material ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Differential Pressure ◽  
Sandstone Sample ◽  
Stress States ◽  
Rock Springs ◽  
Stage 1

The presence of compliant pores in rocks is important for understanding the stress–strain behaviors under different stress conditions. This paper describes findings on the effect of compliant pores on the mechanical behavior of a reservoir sandstone under hydrostatic and triaxial compression. Laboratory experiments were conducted at reservoir temperature on Weber Sandstone samples from the Rock Springs Uplift, Wyoming. Each experiment was conducted at three sequential stages: (stage 1) increase in the confining pressure while maintaining the pore pressure, (stage 2) increase in the pore pressure while maintaining the confining pressure, and (stage 3) application of the deviatoric load to failure. The nonlinear pore pressure – volumetric strain relationship governed by compliant pores under low confining pressure changes to a linear behavior governed by stiff pores under higher confining pressure. The estimated compressibilities of the matrix material in sandstone samples are close to the typical compressibility of quartz. Because of the change in pore structures during stage 1 and stage 2 loadings, the estimated bulk compressibilities of the sandstone sample under the lowest confining pressure decrease with increasing differential pressure. The increase in crack initiation stress is limited with increasing differential pressure because of similar total crack length governed by initial compliant porosity in sandstone samples.

scholarly journals THE BEHAVIOR CHARACTERISTICS OF A RESERVOIR LEVEE SUBJECTED TO INCREASING WATER LEVELS

2017 ◽  
Vol 23 (1) ◽  
pp. 15-27
Author(s):  
Chung-Won LEE ◽  
Yong-Seong KIM ◽  
Sung-Yong PARK ◽  
Dong-Gyun KIM ◽  
Gunn HEO
Keyword(s):  
Hydraulic Fracturing ◽  
Real Time ◽  
Pore Water ◽  
Volumetric Strain ◽  
Water Levels ◽  
The Core ◽  
The Stability ◽  
Centrifugal Model ◽  
Behavior Characteristics ◽  
Plastic Volumetric Strain

Centrifugal model testing has been widely used to study the stability of levees. However, there have been a limited number of physical studies on levees where the velocity of increasing water levels was considered. To investigate the behavior characteristics of reservoir levees with different velocities of increasing water levels, centrifugal model tests and seepage-deformation coupled analyses were conducted. Through this study, it was confirmed that increasing water levels at higher velocities induces dramatic increases in the displacement, plastic volumetric strain and risk of hydraulic fracturing occurring in the core of the levee. Hence, real-time monitoring of the displacement and the pore water pres­sure of a levee is important to ensure levee stability.

Sign in / Sign up

Export Citation Format

Share Document