scholarly journals Retorting conditions affect palatability and physical characteristics of canned cat food

2017 ◽  
Vol 6 ◽  
Author(s):  
Esther A. Hagen-Plantinga ◽  
Denmark F. Orlanes ◽  
Guido Bosch ◽  
Wouter H. Hendriks ◽  
Antonius F. B. van der Poel

AbstractThe effects of different temperature and time conditions during retorting of canned cat food on physicochemical characteristics and palatability were examined. For this purpose, lacquer cans containing an unprocessed loaf-type commercial cat food were heated in a pressurised retorting system at three specified temperature–time profiles (113°C/232 min, 120°C/103 min and 127°C/60 min) to equal a similar lethality (F0 value = 30). Physicochemical properties (viscosity, texture, particle size, pH) were determined, and a 10 d three-bowl palatability test was performed with ten European shorthair cats. Retorting at 113°C/232 min resulted in differences in all the physical parameters examined (<viscosity, firmness, adhesiveness, and > particle size). Significant pH differences were observed (6·53, 6·63 and 6·66 for T113/232, 120 and 127°C, respectively). Preference ratios were 0·38, 0·31 and 0·31 for T113/232, 120 and 127°C, respectively (P = 0·067). It can be concluded that different retorting temperature–time profiles with equal F0 value significantly affect physical characteristics and tended to affect palatability of moist cat food.

2013 ◽  
Vol 826 ◽  
pp. 175-182
Author(s):  
Le Fu Lv ◽  
Guo Sheng Gai ◽  
Chun Sheng Liu ◽  
Yu Fen Yang ◽  
Zhen Quan He ◽  
...  

The K-feldspar rocks, mechanically activated by a microcrystalline mill with an organic activator, were used to study their physical properties and kinetics of element release. The results showed that the microcrystalline grinding reduced particle size, significantly increased specific surface area, obviously improved the morphologies, and broke the lattice structure and increased abundance of amorphous and disordered constituents in K-feldspar rocks within 45 minutes of grinding. Further grinding beyond 45 minutes resulted in an undesirable effect. The microcrystalline grinding also improved release amount of K, Na, Si, Al, Fe and P, and increased the value of pH and EC in extracting solution. Among the grinding treatments, the best physicochemical properties were obtained at 45 minutes and the energy consumption was lower. In comparison to the ordinary K-feldspar rocks, the physical characteristics of the activated K-feldspar rocks were changed significantly. These changes enhanced the nutrient release from the K-feldspar rocks. Thus, microcrystalline grinding technology was important to exploit and utilize the K-feldspar rocks.


Author(s):  
Giscard K. Kaptso ◽  
Nicolas Y. Njintang ◽  
Joseph D. Hounhouigan ◽  
Joel Scher ◽  
Carl M.F. Mbofung

The present study is part of a project aimed at producing bambara groundnut (Voandzeia subterranean) flours for the preparation of koki (a steamed cooked paste). The flours were produced from the black (BBG) and white (WBG) varieties by the combined processes of soaking, drying, dehulling and milling. Some physicochemical characteristics of the flours were evaluated and the effects of flour particle size, salt concentration and pH on their functional properties were investigated. Significant varietal influence was indicated on the proteins and carbohydrates with the WBG variety showing high level of proteins (19.7%) and the BBP variety the highest carbohydrate content (61.7%). It was equally observed that an increase in NaCl tends to induce a reduction in the water absorption capacity (WAC), foam capacity and emulsion properties. The emulsion and foam capacities were observed to be at their minimum values within the pH range 2 and 4.


Author(s):  
Archana Nerella ◽  
Basava Dontamsetti ◽  
Aruna Mantena

The objective of the current investigation was to prepare solid lipid nanoparticles (SLNs) from different lipids and to study the effect of lipids on physicochemical characteristics of letrozole loaded SLN. In order to prepare small, stable, uniform and high Letrozole loaded SLNs, many factors such as lipid and stabilizer concentration and preparation parameters can be considered. Out of these, we have selected solid lipid as lipid matrix to investigate an effect on SLNs. SLNs were prepared using different lipids by modified hot sonication method. The effect of different lipids and stabilizers on physicochemical characteristics of Letrozole loaded SLNs were investigated. Letrozole loaded SLNs showed different physicochemical properties and release profiles according to used solid lipid. In case of particle size, SLN1 showed biggest particle size (532.5 ± 26.4nm) and highest encapsulation efficiency (81.37 ± 6.72%) and, SLN4 showed highest cumulative drug percentage (89.4 ± 1.8%, 24 h) release. These results suggest that lipids type affect physicochemical properties and release profile of SLN. The choice of lipid and stabilizer played important role on the physicochemical characteristics and in vitro release of Letrozole loaded SLNs.


2020 ◽  
Vol 10 (3) ◽  
pp. 169-184
Author(s):  
Rachna Anand ◽  
Arun Kumar ◽  
Arun Nanda

Background: Solubility and dissolution profile are the major factors which directly affect the biological activity of a drug and these factors are governed by the physicochemical properties of the drug. Crystal engineering is a newer and promising approach to improve physicochemical characteristics of a drug without any change in its pharmacological action through a selection of a wide range of easily available crystal formers. Objective: The goal of this review is to summarize the importance of crystal engineering in improving the physicochemical properties of a drug, methods of design, development, and applications of cocrystals along with future trends in research of pharmaceutical co-crystals. Co-crystallization can also be carried out for the molecules which lack ionizable functional groups, unlike salts which require ionizable groups. Conclusion: Co-crystals is an interesting and promising research area amongst pharmaceutical scientists to fine-tune the physicochemical properties of drug materials. Co-crystallization can be a tool to increase the lifecycle of an older drug molecule. Crystal engineering carries the potential of being an advantageous technique than any other approach used in the pharmaceutical industry. Crystal engineering offers a plethora of biopharmaceutical and physicochemical enhancements to a drug molecule without the need of any pharmacological change in the drug.


Agronomy ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 274
Author(s):  
Sara Mayo-Prieto ◽  
Alejandra J. Porteous-Álvarez ◽  
Sergio Mezquita-García ◽  
Álvaro Rodríguez-González ◽  
Guzmán Carro-Huerga ◽  
...  

Spain has ranked 6th on the harvested bean area and 8th in bean production in the European Union (EU). The soils of this area have mixed silt loam and sandy loam texture, with moderate clay content, neutral or acidic pH, rich in organic matter and low carbonate levels, providing beans with high water absorption capacity and better organoleptic qualities after cooking. Similar to other crops, it is attacked by some phytopathogens. Hitherto, chemical methods have been used to control these organisms. However, with the Reform of the Community Agrarian Policy in the EU, the number of authorized plant protection products has been reduced to prevail food security, as well as to be sustainable in the long term, giving priority to the non-chemical methods that use biological agents, such as Trichoderma. This study aimed to investigate the relative importance of various crop soil parameters in the adaptation of Trichoderma spp. autoclaved soils (AS) and natural soils (NS) from the Protected Geographical Indication (PGI) “Alubia La Bañeza—León” that were inoculated with Trichoderma velutinum T029 and T. harzianum T059 and incubated in a culture chamber at 25 °C for 15 days. Their development was determined by quantitative PCR. Twelve soil samples were selected and analyzed from the productive zones of Astorga, La Bañeza, La Cabrera, Esla-Campos and Páramo. Their physicochemical characteristics were different by zone, as the texture of soils ranged between sandy loam and silt loam and the pH between strongly acid and slightly alkaline, as well as the organic matter (OM) concentration between low and remarkably high. Total C and N concentrations and their ratio were between medium and high in most of the soils and the rest of the micronutrients had an acceptable concentration except for Paramo’s soil. Both Trichoderma species developed better in AS than in NS, T. velutinum T029 grew better with high levels of OM, total C, ratio C:N, P, K, Fe, and Zn than T. harzianum T059 in clay soils, with the highest values of cation exchange capacity (CEC), pH, Ca, Mg and Mn. These effects were validated by Canonical Correlation Analysis (CCA), texture, particularly clay concentration, OM, electrical conductivity (EC), and pH (physical parameters) and B and Cu (soil elements) are the main factors explaining the influence in the Trichoderma development. OM, EC, C:N ratio and Cu are the main soil characteristics that influence in T. velutinum T029 development and pH in the development of T. harzianum T059.


Agriculture ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 374
Author(s):  
Teresa Szczęsna ◽  
Ewa Waś ◽  
Piotr Semkiw ◽  
Piotr Skubida ◽  
Katarzyna Jaśkiewicz ◽  
...  

The aim of this study was to determine the influence of storage temperature and time on physicochemical parameters of starch syrups recommended for the winter feeding of bee colonies. The studies included commercially available three starch syrups and an inverted saccharose syrup that were stored at different temperatures: ca. 20 °C, 10–14 °C, and ca. 4 °C. Physicochemical parameters of fresh syrups (immediately after purchase) and syrups after 3, 6, 9, 12, 15, 18, 21, and 24 months of storage at the abovementioned temperatures were measured. It was observed that the rate of unfavorable changes in chemical composition of starch syrups and the inverted saccharose syrup, mainly the changes in the 5-hydroxymethylfurfural (HMF) content, depended on the type of a syrup and storage conditions (temperature, time). Properties of tested starch syrups intended for winter feeding of bees stored at ca. 20 °C maintained unchanged for up to 6 months, whereas the same syrups stored at lower temperatures (10–14 °C) maintained unchanged physicochemical parameters for about 12 months. In higher temperatures, the HMF content increased. To date, the influence of this compound on bees has not been thoroughly investigated.


Author(s):  
Longzhe Jin ◽  
Jianguo Liu ◽  
Jingzhong Guo ◽  
Jiaying Wang ◽  
Tianyang Wang

AbstractTo investigate the factors affecting the wettability of copper mine blasting dust, the primary blasting dust was collected from an open-pit copper mine and separated into hydrophilic blasting dust (HLBD) and hydrophobic blasting dust (HBBD) using water flotation method. The physicochemical properties of HLBD and HBBD were measured and compared with each other. The properties included particle size distributions (PSDs), micromorphologies, pore structures, mineral components and surface organic carbon functional groups. The results show that particle size and pore structure of the blasting dust are the main factors affecting its wettability. Specifically, particle size of HBBD is smaller than that of HLBD, and their respiratory dust (less than 10 µm) accounts for 61.74 vol% and 53.00 vol%, respectively. The pore structure of HBBD is more developed, and the total pore volume of HBBD is 1.66 times larger than that of HLBD. The identical mineral compositions were detected in HLBD and HBBD by X-rays diffraction (XRD); however, the surface organic hydrophobic component of HBBD is slightly larger than that of HLBD, this may be the reason for the poor wettability of HBBD. This study is significant to understand the effects of physicochemical properties of copper mine blasting dust on its wettability.


1938 ◽  
Vol 67 (1) ◽  
pp. 1-12 ◽  
Author(s):  
Gregory Shwartzman ◽  
S. A. Morell

Several physicochemical properties of the active principles of the phenomenon of local skin reactivity to bacterial filtrates have been investigated. Ultrafiltration through Zsigmondy filters of graded porosities has shown that the active substances are retained by membranes finer than 100 to 120 seconds, whereas coarser ones readily permit their passage. The average porosity of this filtration end-point represents a particle size of about 50 to 100 mµ. When fractionally precipitated with ammonium sulfate, most of the activity of a culture filtrate was concentrated in the two-thirds saturated portion. Isoelectric properties were studied by means of capillary analysis and cataphoresis. At pH 3.0 and below, the substances suspended in the culture filtrates migrated to the cathode; activity in this chamber, however, could not be demonstrated. At pH 4.0 and above, reversal to the anode occurred, as the active materials became negatively charged and readily migrated to this chamber. The isoelectric point, therefore, was considered to be between pH 3.0 and 4.0. Preliminary experiments on adsorption, extraction, and pH stability have been described.


2007 ◽  
Vol 3 (S248) ◽  
pp. 66-73
Author(s):  
J.-E. Arlot

AbstractThe main goal of the astrometry of solar system objects is to build dynamical models of their motions to understand their evolution, to determine physical parameters and to build accurate ephemerides for the preparation and the exploitation of space missions. For many objects, the ground-based observations are still very important because radar or observations from space probes are not available. More, the need of observations on a long period of time makes the ground-based observations necessary. The solar system objects have very different characteristics and the increase of the astrometric accuracy will depend on the objects and on their physical characteristics. The purpose of this communication is to show how to get the best astrometric accuracy.


Sign in / Sign up

Export Citation Format

Share Document