Cold atmospheric plasma activity on microorganisms. A study on the influence of the treatment time and surface

2015 ◽  
Vol 81 (4) ◽  
Author(s):  
C. L. Xaplanteris ◽  
E. D. Filippaki ◽  
J. K. Christodoulakis ◽  
M. A. Kazantzaki ◽  
E. P. Tsakalos ◽  
...  

The second half of the 20th century can be characterized and named as the ‘plasma era’, as the plasma gathered scientific interest because of its special physical behaviour. Thus, it was considered as the fourth material state and the plasma physics began to form consequently. In addition to this, many important applications of plasma were discovered and put to use. Especially, in last few decades, there has been an increased interest in the use of cold atmospheric plasma in bio-chemical applications. Until now, thermal plasma has been commonly used in many bio-medical and other applications; however, more recent efforts have shown that plasma can also be produced at lower temperature (close to the environment temperature) by using ambient air in an open space (in atmospheric pressure). However, two aspects remain neglected: firstly, low-temperature plasma production with a large area, and secondly, acquiring the necessary knowledge and understanding the relevant interaction mechanisms of plasma species with microorganisms. These aspects are currently being investigated at the ‘Demokritos’ Plasma Laboratory in Athens, Greece with radio frequency (27.12 MHz and it integer harmonics)-driven sub-atmospheric pressure plasma (100 Pa). The first aspect was achieved with atmospheric plasma being produced at a low temperature (close to the environment temperature) and in a large closed space systems. Regarding the plasma effect on living microorganisms, preliminary experiments and findings have already been carried out and many more have been planned for the near future.

2021 ◽  
Vol 6 (1) ◽  
pp. 78-86
Author(s):  
N. Yu. Moskalenko ◽  
O. A. Kudryashova ◽  
L. S. Kudryashov ◽  
S. L. Tikhonov ◽  
N. V. Tikhonova ◽  
...  

It is known that processing methods ensuring partial or full microbial inactivation are quite limited. Therefore, it is of great interest to develop technique and technologies allowing the effective action on microorganisms without a significant influence on product properties. The use of cold plasma can be one of the promising methods of meat product treatment by cold sterilization. The present work examines a possibility of chilled meat treatment with low-temperature atmospheric-pressure plasma to increase its stability to microbial spoilage and extend shelf life. To obtain low temperature plasma, the equipment developed by the designing department “Plasmamed” was used. Chilled meat was treated with low-temperature atmospheric-pressure argon plasma for 5, 10, 20 and 30 min. Samples were stored at a temperature of 2–4 °C for 10 days. Organoleptic indices, moisture weight fraction, changes in pH and water activity were analyzed before treatment and during storage. Sanitary microbiological analyses were carried out by the following indicators: quantity of mesophilic aerobic and facultative anaerobic microorganisms (QMAFAnM), the presence and quantity of coliforms, Salmonella, Escherichia coli, Listeria monocytogenes, Proteus. It was shown that meat cold treatment with argon plasma inhibited the development of mesophilic microorganisms. The colony forming units detected in the samples after ten days of storage were determined by the duration of exposure to plasma. It was proved that meat treatment for 15 and 30 min had the bactericidal effect and facilitated an improvement in meat color during storage. The organoleptic indices of the samples treated with plasma corresponded to the requirements of standards and approved consumer characteristics.


2015 ◽  
Vol 4 (6) ◽  
pp. 313-317
Author(s):  
Hideaki SHAKUTSUI ◽  
Yuhshi KAJI ◽  
Kenya HIROSAWA ◽  
Hiroshi TAKAHASHI ◽  
Hiroshi AKAMATSU ◽  
...  

2019 ◽  
Vol 8 (11) ◽  
pp. 1930 ◽  
Author(s):  
Bih-Show Lou ◽  
Chih-Ho Lai ◽  
Teng-Ping Chu ◽  
Jang-Hsing Hsieh ◽  
Chun-Ming Chen ◽  
...  

Using the Taguchi method to narrow experimental parameters, the antimicrobial efficiency of a cold atmospheric plasma jet (CAPJ) treatment was investigated. An L9 array with four parameters of CAPJ treatments, including the application voltage, CAPJ-sample distance, argon (Ar) gas flow rate, and CAPJ treatment time, were applied to examine the antimicrobial activity against Escherichia coli (E. coli). CAPJ treatment time was found to be the most influential parameter in its antimicrobial ability by evaluation of signal to noise ratios and analysis of variance. 100% bactericidal activity was achieved under the optimal bactericidal activity parameters including the application voltage of 8.5 kV, CAPJ-sample distance of 10 mm, Ar gas flow rate of 500 sccm, and CAPJ treatment time of 300 s, which confirms the efficacy of the Taguchi method in this design. In terms of the mechanism of CAPJ’s antimicrobial ability, the intensity of hydroxyl radical produced by CAPJ positively correlated to its antimicrobial efficiency. The CAPJ antimicrobial efficiency was further evaluated by both DNA double-strand breaks analysis and scanning electron microscopy examination of CAPJ treated bacteria. CAPJ destroyed the cell wall of E. coli and further damaged its DNA structure, thus leading to successful killing of bacteria. This study suggests that optimal conditions of CPAJ can provide effective antimicrobial activity and may be grounds for a novel approach for eradicating bacterial infections.


Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 935 ◽  
Author(s):  
Jacek Tyczkowski ◽  
Hanna Kierzkowska-Pawlak ◽  
Jan Sielski ◽  
Iwona Krawczyk-Kłys

This paper proposed a kinetic model that can describe the changes in the adhesion properties of styrene–butadiene (SBS) block copolymer surfaces under the influence of low-temperature plasma treatment. As a measure of these changes, the peel strength of joints formed between the copolymer surface and the polyurethane adhesive was chosen. Five types of low-temperature low-pressure RF plasma, two inert plasmas (Ar and He), and three reactive plasmas (O2, CO2, and CCl4) were tested. It was found that for all these types of plasma, the peel strength with the plasma treatment time first increases rapidly reaching a maximum value, and then there is a visible decrease in peel strength, after which the peel strength increases again. This dependence of the peel strength on the plasma treatment time is very well described by the proposed model, which considers three processes: (1) the generation of radical states followed by the creation of functional groups involved in the adhesive bonding process, (2) the surface cross-linking that decreases the concentration of these functional groups, and (3) the formation of nano-roughness. The model analysis revealed differences between the action of reactive and inert plasmas in the SBS surface cross-linking mechanism and preferential etching process, as well as differences in the generation of radical states between the O2 plasma (electron process) and other plasmas tested (ionic processes).


Sign in / Sign up

Export Citation Format

Share Document