scholarly journals Computed X-ray Tomography of Powder Metallurgy Product for Rapid, Quantitative Size and Shape Distribution Analysis

2016 ◽  
Vol 22 (S3) ◽  
pp. 1756-1757
Author(s):  
Noah Budiansky ◽  
Daniel P. Dennies ◽  
Joel Forman ◽  
David Wong ◽  
Joe Tucker
2019 ◽  
Vol 3 (1) ◽  
pp. 3 ◽  
Author(s):  
Tobias Thiede ◽  
Tatiana Mishurova ◽  
Sergei Evsevleev ◽  
Itziar Serrano-Munoz ◽  
Christian Gollwitzer ◽  
...  

The quality of components made by laser beam melting (LBM) additive manufacturing is naturally influenced by the quality of the powder bed. A packing density <1 and porosity inside the powder particles lead to intrinsic voids in the powder bed. Since the packing density is determined by the particle size and shape distribution, the determination of these properties is of significant interest to assess the printing process. In this work, the size and shape distribution, the amount of the particle’s intrinsic porosity, as well as the packing density of micrometric powder used for LBM, have been investigated by means of synchrotron X-ray computed tomography (CT). Two different powder batches were investigated: Ti–6Al–4V produced by plasma atomization and stainless steel 316L produced by gas atomization. Plasma atomization particles were observed to be more spherical in terms of the mean anisotropy compared to particles produced by gas atomization. The two kinds of particles were comparable in size according to the equivalent diameter. The packing density was lower (i.e., the powder bed contained more voids in between particles) for the Ti–6Al–4V particles. The comparison of the tomographic results with laser diffraction, as another particle size measurement technique, proved to be in agreement.


Nanomaterials ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 154
Author(s):  
Mathias Urbain ◽  
Florian Riporto ◽  
Sandrine Beauquis ◽  
Virginie Monnier ◽  
Jean-Christophe Marty ◽  
...  

Phase-pure, highly crystalline sub-50 nm LiNbO3 nanocrystals were prepared from a non-aqueous solvothermal process for 72 h at 230 °C and a commercial precursor solution of mixed lithium niobium ethoxide in its parent alcohol. A systematic variation of the reaction medium composition with the addition of different amounts of co-solvent including butanol, 1,3-propanediol, 1,4-butanediol, and 1,5-pentanediol resulted in the formation of nanocrystals of adjustable mean size and shape anisotropy, as demonstrated from XRD measurements and TEM imaging. Colloidal stability of ethanol- and water-based suspensions was evaluated from dynamic light scattering (DLS)/zeta potential studies and correlated with FTIR data. Thanks to the evolution in the nanocrystal size and shape distribution we observed, as well as to the available literature on the alkoxide chemistry, the reaction pathways and growth mechanisms were finally discussed with a special attention on the monomer formation rate, leading to the nucleation step. The polar, non-perovskite crystalline structure of LiNbO3 was also evidenced to play a major role in the nanocrystal shape anisotropy.


2015 ◽  
Vol 772 ◽  
pp. 284-289 ◽  
Author(s):  
Sabuj Mallik ◽  
Jude Njoku ◽  
Gabriel Takyi

Voiding in solder joints poses a serious reliability concern for electronic products. The aim of this research was to quantify the void formation in lead-free solder joints through X-ray inspections. Experiments were designed to investigate how void formation is affected by solder bump size and shape, differences in reflow time and temperature, and differences in solder paste formulation. Four different lead-free solder paste samples were used to produce solder bumps on a number of test boards, using surface mount reflow soldering process. Using an advanced X-ray inspection system void percentages were measured for three different size and shape solder bumps. Results indicate that the voiding in solder joint is strongly influenced by solder bump size and shape, with voids found to have increased when bump size decreased. A longer soaking period during reflow stage has negatively affectedsolder voids. Voiding was also accelerated with smaller solder particles in solder paste.


1999 ◽  
Vol 45 (149) ◽  
pp. 22-30 ◽  
Author(s):  
F. Pauer ◽  
S. Kipfstuhl ◽  
W. F. Kuhs ◽  
H. Shoji

AbstractWe performed microscopic observations and a statistical study of the number, size and shape distribution of clathrates in the GRIP (Greenland Ice Core Project) deep ice core, using 185 samples from a depth range of 1016–3014 m, spanning a period of 6 to >110 ka BP and encompassing the Holocene, Wisconsin and Eemian periods. The number concentration of the clathrates varied considerably with climatic changes. It was possible to detect the rapid climatic oscillations in the last glacial between 13 and 110 ka BP, the Dansgaard–Oeschger cycles, in the number-concentration profile of clathrates. The mean volume of clathrates is less clearly influenced by climatic factors, with a tendency towards greater volumes in warmer periods, but also a growth of clathrates with depth could be detected. This growth rate was calculated to be 3.1 × 10-12 cm3 a-1. The amount of gases captured in the clathrates is estimated to be significantly smaller than the total amount of air determined by gas-concentration measurements. This points to diffusion processes of atmospheric gases within the ice matrix.


Author(s):  
Md Mehtab Alam and B.S Motgi

The paper deals with detailed study on microstructure and mechanical properties of aluminum 7068 reinforced with fly ash and silicon carbide by powder metallurgy, aluminum 7068, silicon carbide and fly ash were taken in powder form of required size and mixed together in varying proportion according to specification and compacted with pressure of 400MPa using hydraulic press to make samples and then samples were sintered at 600°c for 2 hours, the samples were tested for density, compressive strength, hardness and microstructure was analyzed using scanning electron microscope, energy dispersive x-ray study was carried out in order to confirm presence of silicon carbide and fly ash in aluminum matrix.


2020 ◽  
Vol 1 (4) ◽  
pp. 187-193
Author(s):  
Elaheh Gharibshahian

KTiOPO4 nanoparticles are known as the best candidate to utilize for second-harmonic generation in multiphoton microscopes and bio labels. Size and shape are important and effective parameters to control the properties of nanoparticles. In this paper, we will investigate the role of capping agent concentration on the size and shape control of KTP nanoparticles. We synthesized KTP nanoparticles by the co-precipitation method. Polyvinyl alcohol with different mole ratios to titanium ion (1:3, 1:2, 1:1) was used as a capping agent. Products were examined by X-ray diffraction patterns and scanning electron microscopy analyses. X-ray diffraction patterns confirmed the formation of the KTP structure. The biggest (56.36nm) and smallest (39.42nm) grain size were obtained by 1:3 and 1:1 mole ratios of capping agent, respectively. Dumbly, spherical and polyhedral forms of KTP nanoparticles were observed by the change in capping agent mole ratio. The narrowest size distribution of KTiOPO4 nanoparticles was obtained at 1:1 mole ratio of capping agent. Doi: 10.28991/HIJ-2020-01-04-06 Full Text: PDF


Sign in / Sign up

Export Citation Format

Share Document