scholarly journals Interfacial Assembly and Jamming of Polyelectrolyte Surfactants: A Simple Route To Print Liquids in Low-Viscosity Solution

2020 ◽  
Vol 12 (15) ◽  
pp. 18116-18122 ◽  
Author(s):  
Ruiyan Xu ◽  
Tan Liu ◽  
Huilou Sun ◽  
Beibei Wang ◽  
Shaowei Shi ◽  
...  
Keyword(s):  
Viscosity Solution ◽  
Interfacial Assembly ◽  
Simple Route ◽  
Low Viscosity

Evidence of re-entrant behavior in laponite-PEO systems

2005 ◽  
Vol 899 ◽  
Author(s):  
Hossein Baghdadi ◽  
Surita R. Bhatia ◽  
Elizabeth E. C. Jensen ◽  
Nalini Easwar
Keyword(s):  
Molecular Weight ◽  
Viscosity Solution ◽  
High Viscosity ◽  
Polymer Chains ◽  
Low Viscosity ◽  
End Distance ◽  
Depletion Force ◽  
Poly Ethylene Oxide ◽  
Poly Ethylene ◽  
Electrostatic Repulsions

AbstractRheology and dynamic light scattering capture re-entrant behavior of laponite-polymer systems. Neat laponite under basics conditions and concentrations of 2wt% or greater forms a viscoelastic soft glass due to electrostatic repulsions. We show that that addition of low molecular weight poly(ethylene oxide) (PEO) melts the glass due to a depletion force. The depletion force speeds up dynamics in the system resulting in a low viscosity solution. A re-entrant viscoelastic solid is formed with the addition of high molecular weight PEO due to the polymer chains bridging between laponite particles. As expected the transition from a low to high viscosity solution scales with the polymer mean square end-to-end distance and gap between laponite particles.

Portable rheometer to overcome the challenge of measuring low viscosity solution of acrylamide-based polymers at high temperature with an affordable cost for O&G applications

2021 ◽  
Vol 65 (5) ◽  
pp. 1053-1063
Author(s):  
S. Antignard ◽  
G. Dupuis ◽  
C. Favéro ◽  
L. Rodriguez ◽  
B. Grassl
Keyword(s):  
High Temperature ◽  
Viscosity Solution ◽  
Low Viscosity

Effect of diffusion on Förster resonance energy transfer in low-viscosity solution

2014 ◽  
Vol 140 (21) ◽  
pp. 214508 ◽  
Author(s):  
Atsushi Muratsugu ◽  
Junji Watanabe ◽  
Shuichi Kinoshita
Keyword(s):  
Energy Transfer ◽  
Viscosity Solution ◽  
Resonance Energy Transfer ◽  
Resonance Energy ◽  
Forster Resonance Energy Transfer ◽  
Förster Resonance Energy Transfer ◽  
Low Viscosity ◽  
Förster Resonance

The Use of Styrenes as Embedding Media for Electron Microscopy

1971 ◽  
Vol 29 ◽  
pp. 488-489
Author(s):  
Edward D. De-Lamater ◽  
Eric Johnson ◽  
Thad Schoen ◽  
Cecil Whitaker
Keyword(s):  
Electron Microscopy ◽  
Surface Tension ◽  
Ultraviolet Light ◽  
Methyl Ethyl Ketone Peroxide ◽  
Methyl Ethyl ◽  
Styrene Polymerization ◽  
Radical Initiation ◽  
Tertiary Butyl ◽  
Low Viscosity ◽  
Free Radical Initiation

Monomeric styrenes are demonstrated as excellent embedding media for electron microscopy. Monomeric styrene has extremely low viscosity and low surface tension (less than 1) affording extremely rapid penetration into the specimen. Spurr's Medium based on ERL-4206 (J.Ultra. Research 26, 31-43, 1969) is viscous, requiring gradual infiltration with increasing concentrations. Styrenes are soluble in alcohol and acetone thus fitting well into the usual dehydration procedures. Infiltration with styrene may be done directly following complete dehydration without dilution.Monomeric styrenes are usually inhibited from polymerization by a catechol, in this case, tertiary butyl catechol. Styrene polymerization is activated by Methyl Ethyl Ketone peroxide, a liquid, and probably acts by overcoming the inhibition of the catechol, acting as a source of free radical initiation.Polymerization is carried out either by a temperature of 60°C. or under ultraviolet light with wave lengths of 3400-4000 Engstroms; polymerization stops on removal from the ultraviolet light or heat and is therefore controlled by the length of exposure.

Some quantitative applications of vascular corrosion casting

1992 ◽  
Vol 50 (1) ◽  
pp. 738-739
Author(s):  
Fred E. Hossler
Keyword(s):  
Blood Vessels ◽  
Nuclear Orientation ◽  
Three Dimensional ◽  
Surrounding Tissue ◽  
Confocal Laser ◽  
Corrosion Casting ◽  
Venous Valve ◽  
Casting Technique ◽  
Low Viscosity ◽  
Quantitative Measurements

Preparation of replicas of the complex arrangement of blood vessels in various organs and tissues has been accomplished by infusing low viscosity resins into the vasculature. Subsequent removal of the surrounding tissue by maceration leaves a model of the intricate three-dimensional anatomy of the blood vessels of the tissue not obtainable by any other procedure. When applied with care, the vascular corrosion casting technique can reveal fine details of the microvasculature including endothelial nuclear orientation and distribution (Fig. 1), locations of arteriolar sphincters (Fig. 2), venous valve anatomy (Fig. 3), and vessel size, density, and branching patterns. Because casts faithfully replicate tissue vasculature, they can be used for quantitative measurements of that vasculature. The purpose of this report is to summarize and highlight some quantitative applications of vascular corrosion casting. In each example, casts were prepared by infusing Mercox, a methyl-methacrylate resin, and macerating the tissue with 20% KOH. Casts were either mounted for conventional scanning electron microscopy, or sliced for viewing with a confocal laser microscope.

Investigation of thin sections of biological standards by EDX, EELS, and Auger electron spectroscopy

1990 ◽  
Vol 48 (2) ◽  
pp. 184-185
Author(s):  
S. Lehner ◽  
H.E. Bauer ◽  
R. Wurster ◽  
H. Seiler
Keyword(s):  
Processing System ◽  
Beam Current ◽  
Beam Diameter ◽  
Thin Sections ◽  
Biologically Relevant ◽  
Energy Filtering ◽  
Low Viscosity ◽  
Carbon Foils ◽  
Electron Microscopical ◽  
Exchange Membrane

In order to compare different microanalytical techniques commercially available cation exchange membrane SC-1 (Stantech Inc, Palo Alto), was loaded with biologically relevant elements as Na, Mg, K, and Ca, respectively, each to its highest possible concentration, given by the number concentration of exchangeable binding sites (4 % wt. for Ca). Washing in distilled water, dehydration through a graded series of ethanol, infiltration and embedding in Spurr’s low viscosity epoxy resin was followed by thin sectioning. The thin sections (thickness of about 50 nm) were prepared on carbon foils and mounted on electron microscopical finder grids.The samples were analyzed with electron microprobe JXA 50A with transmitted electron device, EDX system TN 5400, and on line operating image processing system SEM-IPS, energy filtering electron microscope CEM 902 with EELS/ESI and Auger spectrometer 545 Perkin Elmer.With EDX, a beam current of some 10-10 A and a beam diameter of about 10 nm, a minimum-detectable mass of 10-20 g Ca seems within reach.

Ultrastructural autoradiography of L6 skeletal-muscle cells exposed to a tritiated macrolide antibiotic (LY237216) in vitro

1992 ◽  
Vol 50 (1) ◽  
pp. 612-613
Author(s):  
S.L. White ◽  
C.B. Jensen ◽  
D.D. Giera ◽  
D.A. Laska ◽  
M.N. Novilla ◽  
...  
Keyword(s):  
Skeletal Muscle ◽  
Quantitative Analysis ◽  
Macrolide Antibiotic ◽  
Circle Method ◽  
Apical Surface ◽  
Polycarbonate Membrane ◽  
L6 Cells ◽  
Low Viscosity ◽  
Erythromycin A

In vitro exposure to LY237216 (9-Deoxo-11-deoxy-9,11-{imino[2-(2-methoxyethoxy)ethylidene]-oxy}-(9S)-erythromycin), a macrolide antibiotic, was found to induce cytoplasmic vacuolation in L6 skeletal muscle myoblast cultures (White, S.L., unpubl). The present study was done to determine, by autoradiographic quantitative analysis, the subcellular distribution of 3H-LY237216 in L6 cells.L6 cells (ATCC, CRL 1458) were cultured to confluency on polycarbonate membrane filters (Millipore Corp., Bedford, MA) in M-199 medium (GIBCO® Labs) with 10% fetal bovine serum. The cells were exposed from the apical surface for 1-hour to unlabelled-compound (0 μCi/ml) or 50 (μCi/ml of 3H-LY237216 at a compound concentration of 0.25 mg/ml. Following a rapid rinse in compound-free growth medium, the cells were slam-frozen against a liquid nitrogen cooled, polished copper block in a CF-100 cryofixation unit (LifeCell Corp., The Woodlands, TX). Specimens were dried in the MDD-C Molecular Distillation Drier (LifeCell Corp.), vapor osmicated and embedded in Spurrs low viscosity resin. Ultrathin sections collected on formvar coated stainless steel grids were counter-stained, then individually mounted on corks. A monolayer of Ilford L4 nuclear emulsion (Polysciences, Inc., Warrington, PA) was placed on the sections, utilizing a modified “loop method”. The emulsions were exposed for 7-weeks in a light-tight box at 4°C. Autoradiographs were developed in Microdol-X developer and examined on a Philips EM410LS transmission electron microscope. Quantitative analysis of compound localization employed the point and circle approach of Williams; incorporating the probability circle method of Salpeter and McHenry.

The concerted use of SEM, TEM, and SCM for examination of resin-dentin interfaces

1994 ◽  
Vol 52 ◽  
pp. 476-477
Author(s):  
B. Van Meerbeek ◽  
L. J. Conn ◽  
E. S. Duke
Keyword(s):  
Surface Layer ◽  
Stress Distribution ◽  
Phosphoric Acid ◽  
Bonding Mechanism ◽  
Restorative Dentistry ◽  
Dental Adhesive ◽  
Low Viscosity ◽  
Dentin Adhesives ◽  
Acid Etch ◽  
Tooth Tissue

Restoration of decayed teeth with tooth-colored materials that can be bonded to tooth tissue has been a highly desirable property in restorative dentistry for many years. Advantages of such an adhesive restorative technique over conventional techniques using non-adhesive metal-based restoratives include improved restoration retention with minimal sacrifice of sound tooth tissue for retention purposes, superior adaptation and sealing of the restoration margins in prevention of caries recurrence, improved stress distribution across the tooth-restoration interface throughout the whole tooth, and even reinforcement of weakened tooth structures. The dental adhesive technology is rapidly changing. An efficient resin bond to enamel has already long been achieved. Its bonding mechanism has been fully elucidated and has proven to be a durable and reliable clinical treatment. However, bonding to dentin represents a greater challenge. After the failures of a dentin acid-etch technique in imitation of the enamel phosphoric-acid-etch technique and a bonding procedure based on chemical adhesion, modern dentin adhesives are currently believed to bond to dentin by a micromechanical hybridization process. This process is developed by an initial demineralization of the dentin surface layer with acid etchants exposing a collagen fibril arrangement with interfibrillar microporosities that subsequently become impregnated by low-viscosity monomers. Although the development of such a hybridization process has well been documented in the literature, questions remain with respect to parameters of-primary importance to adhesive efficacy.

The microstructure of functionalized poLyacrylonitrile beads for bioseparations

1990 ◽  
Vol 48 (4) ◽  
pp. 1094-1095
Author(s):  
Eduardo A. Kamenetzky ◽  
David A. Ley
Keyword(s):  
Aqueous Solution ◽  
Affinity Chromatography ◽  
Pore Size Distribution ◽  
Pore Size ◽  
Surface Coverage ◽  
Vacuum Impregnation ◽  
Thin Sections ◽  
Selective Staining ◽  
Low Viscosity ◽  
Diamond Knife

The microstructure of polyacrylonitrile (PAN) beads for affinity chromatography bioseparations was studied by TEM of stained ultramicrotomed thin-sections. Microstructural aspects such as overall pore size distribution, the distribution of pores within the beads, and surface coverage of functionalized beads affect performance properties. Stereological methods are used to quantify the internal structure of these chromatographic supports. Details of the process for making the PAN beads are given elsewhere. TEM specimens were obtained by vacuum impregnation with a low-viscosity epoxy and sectioning with a diamond knife. The beads can be observed unstained. However, different surface functionalities can be made evident by selective staining. Amide surface coverage was studied by staining in vapor of a 0.5.% RuO4 aqueous solution for 1 h. RuO4 does not stain PAN but stains, amongst many others, polymers containing an amide moiety.

Sign in / Sign up

Export Citation Format

Share Document