scholarly journals Experimental and empirical investigation of a CI engine fuelled with blends of diesel and roselle biodiesel

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Tikendra Nath Verma ◽  
Upendra Rajak ◽  
Abhishek Dasore ◽  
Asif Afzal ◽  
A. Muthu Manokar ◽  
...  
Keyword(s):  
Alternative Fuels ◽  
Fuel Injection ◽  
Full Range ◽  
Injection Timing ◽  
Gas Temperature ◽  
Fuel Blends ◽  
Technical Ability ◽  
Compression Ignition Engines ◽  
Range Characterization ◽  
Exhaust Gas Temperature

AbstractThe continuous rise in demand, combined with the depletion of the world's fossil fuel reserves, has forced the search for alternative fuels. The biodiesel produced from Roselle is one such indigenous biodiesel with tremendous promise, and its technical ability to operate with compression ignition engines is studied in this work. To characterize the fuel blends, researchers used experimental and empirical approaches while operating at engine loads of 25, 50, 75, and 100%, and with fuel injection timings of 19°, 21°, 23°, 25°, and 27° before top dead center. Results indicate that for 20% blend with the change of injection timing from 19° bTDC to 27° bTDC at full load, brake specific fuel consumption and exhaust gas temperature was increased by 15.84% and 4.60% respectively, while brake thermal efficiency decreases by 4.4%. Also, an 18.89% reduction in smoke, 5.26% increase in CO2, and 12.94% increase in NOx were observed. In addition, an empirical model for full range characterization was created. With an r-squared value of 0.9980 ± 0.0011, the artificial neural network model constructed to characterize all 10 variables was able to predict satisfactorily. Furthermore, substantial correlation among specific variables suggested that empirically reduced models were realistic.

scholarly journals Engine Behaviour Characterisation of Roselle Biodiesel Through Experimental and Empirical Method

2021 ◽  
Author(s):  
Tikendra Nath Verma ◽  
Upendra Rajak ◽  
Satishchandra Salam ◽  
Asif Afzal ◽  
A. Muthu Manokar ◽  
...  
Keyword(s):  
Alternative Fuels ◽  
Fuel Injection ◽  
Full Range ◽  
Empirical Method ◽  
Injection Timing ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Fuel Blends ◽  
Exhaust Gas Temperature

Abstract Persistent increase in demand and depletion of world fossil fuel reserve has necessitated the lookout for alternative fuels. One such indigenous biodiesel with significant potential is the biodiesel extracted from Roselle whose technical feasibility to operate with compression ignition engine is investigated in this study. Experimental and empirical methodologies had been employed to characterise the fuel blends while operating at engine loads of 25%, 50%, 75% and 100%, and with fuel injection timings of 19°, 21°, 23°, 25° and 27° bTDC. Results showed that for 20% blend, with advanced injection timing from 19° bTDC to 27° bTDC at full load, brake specific fuel consumption and exhaust gas temperature for 20% blend was higher by 15.84% and 4.60%, while decrease in brake thermal efficiency by 4.4%. Also, 18.89% reduction in smoke, 5.26% increase in CO2 and 12.94% increase in NOx were observed. In addition, an empirical model was developed for full range characterisation. The artificial neural network model thus developed to characterise all the 10 variables was able to predict satisfactorily with r-squared value of 0.9980 ± 0.0011. Further, high correlation amongst certain variables indicated to plausible empirically reduced models.

scholarly journals Performance evaluation of common rail direct injection (CRDI) engine fuelled with Uppage Oil Methyl Ester (UOME)

2015 ◽  
Vol 4 (1) ◽  
pp. 1-10 ◽  
Author(s):  
D.N. Basavarajappa ◽  
N. R. Banapurmath ◽  
S.V. Khandal ◽  
G. Manavendra
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Engines ◽  
High Speed ◽  
Alternative Fuels ◽  
High Pressures ◽  
Fuel Injection ◽  
Injection Timing ◽  
Engine Operation ◽  
Performance And Emission

For economic and social development of any country energy is one of the most essential requirements. Continuously increasing price of crude petroleum fuels in the present days coupled with alarming emissions and stringent emission regulations has led to growing attention towards use of alternative fuels like vegetable oils, alcoholic and gaseous fuels for diesel engine applications. Use of such fuels can ease the burden on the economy by curtailing the fuel imports. Diesel engines are highly efficient and the main problems associated with them is their high smoke and NOx emissions.  Hence there is an urgent need to promote the use of alternative fuels in place of high speed diesel (HSD) as substitute. India has a large agriculture base that can be used as a feed stock to obtain newer fuel which is renewable and sustainable. Accordingly Uppage oil methyl ester (UOME) biodiesel was selected as an alternative fuel. Use of biodiesels in diesel engines fitted with mechanical fuel injection systems has limitation on the injector opening pressure (300 bar). CRDI system can overcome this drawback by injecting fuel at very high pressures (1500-2500 bar) and is most suitable for biodiesel fuels which are high viscous. This paper presents the performance and emission characteristics of a CRDI diesel engine fuelled with UOME biodiesel at different injection timings and injection pressures. From the experimental evidence it was revealed that UOME biodiesel yielded overall better performance with reduced emissions at retarded injection timing of -10° BTDC in CRDI mode of engine operation.

Effect of Fuel Injection Strategy on DPF Regeneration in Single Cylinder Diesel Engine

2015 ◽  
Author(s):  
Sungjun Yoon ◽  
Hongsuk Kim ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Operating Conditions ◽  
Experimental Results ◽  
Exhaust Gas ◽  
Post Injection ◽  
Gas Temperature ◽  
Injection Strategy ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

Stringent emission regulations (e.g., Euro-6) force automotive manufacturers to equip DPF (diesel particulate filter) on diesel cars. Generally, post injection is used as a method to regenerate DPF. However, it is known that post injection deteriorates specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration becomes one of key technologies for diesel powertrain equipped with a DPF. This paper presents correlations between fuel injection strategy and exhaust gas temperature for DPF regeneration. Experimental apparatus consists of a single cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, post injection timing covers from 40 deg aTDC to 110 deg aTDC and double post injection was considered. In addition, effects of injection pressures were investigated. The engine load was varied from low-load to mid-load and fuel amount of post injection was increased up to 10mg/stk. Oil dilution during fuel injection and combustion processes were estimated by diesel loss measured by comparing two global equivalences ratios; one is measured from Lambda sensor installed at exhaust port, the other one is estimated from intake air mass and injected fuel mass. In the present study, the differences in global equivalence ratios were mainly caused from oil dilution during post injection. The experimental results of the present study suggest an optimal engine operating conditions including fuel injection strategy to get appropriate exhaust gas temperature for DPF regeneration. Experimental results of exhaust gas temperature distributions for various engine operating conditions were summarized. In addition, it was revealed that amounts of oil dilution were reduced by splitting post injection (i.e., double post injection). Effects of injection pressure on exhaust gas temperature were dependent on combustion phasing and injection strategies.

Effect of the Fuel Injection Strategy on Diesel Particulate Filter Regeneration in a Single-Cylinder Diesel Engine

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
Sungjun Yoon ◽  
Hongsuk Kim ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Diesel Particulate ◽  
Injection Strategy ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

Stringent emission regulations (e.g., Euro-6) have forced automotive manufacturers to equip a diesel particulate filter (DPF) on diesel cars. Generally, postinjection is used as a method to regenerate the DPF. However, it is known that postinjection deteriorates the specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration is one of the key technologies for diesel powertrains equipped with a DPF. This paper presents correlations between the fuel injection strategy and exhaust gas temperature for DPF regeneration. The experimental apparatus consists of a single-cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, the postinjection timing was in the range of 40 deg aTDC to 110 deg aTDC and double postinjection was considered. In addition, the effects of the injection pressure were investigated. The engine load was varied among low load to midload conditions, and the amount of fuel of postinjection was increased up to 10 mg/stk. The oil dilution during the fuel injection and combustion processes was estimated by the diesel loss measured by comparing two global equivalences ratios: one measured from a lambda sensor installed at the exhaust port and one estimated from the intake air mass and injected fuel mass. In the present study, the differences of the global equivalence ratios were mainly caused by the oil dilution during postinjection. The experimental results of the present study suggest optimal engine operating conditions including the fuel injection strategy to obtain an appropriate exhaust gas temperature for DPF regeneration. The experimental results of the exhaust gas temperature distributions for various engine operating conditions are discussed. In addition, it was revealed that the amount of oil dilution was reduced by splitting the postinjection (i.e., double postinjection). The effects of the injection pressure on the exhaust gas temperature were dependent on the combustion phasing and injection strategies.

Influence of fuel injection strategies on efficiency and particulate emissions of gasoline and ethanol blends in a turbocharged multi-cylinder direct injection engine

2019 ◽  
Vol 22 (1) ◽  
pp. 152-164 ◽  
Author(s):  
Ripudaman Singh ◽  
Taehoon Han ◽  
Mohammad Fatouraie ◽  
Andrew Mansfield ◽  
Margaret Wooldridge ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Multiple Injection ◽  
Fuel Mass ◽  
Direct Injection Engine ◽  
Fuel Blends ◽  
Ethanol Blends ◽  
Injection Strategies

The effects of a broad range of fuel injection strategies on thermal efficiency and engine-out emissions (CO, total hydrocarbons, NOx and particulate number) were studied for gasoline and ethanol fuel blends. A state-of-the-art production multi-cylinder turbocharged gasoline direct injection engine equipped with piezoelectric injectors was used to study fuels and fueling strategies not previously considered in the literature. A large parametric space was considered including up to four fuel injection events with variable injection timing and variable fuel mass in each injection event. Fuel blends of E30 (30% by volume ethanol) and E85 (85% by volume ethanol) were compared with baseline E0 (reference grade gasoline). The engine was operated over a range of loads with intake manifold absolute pressure from 800 to 1200 mbar. A combined application of ethanol blends with a multiple injection strategy yielded considerable improvement in engine-out particulate and gaseous emissions while maintaining or slightly improving engine brake thermal efficiency. The weighted injection spread parameter defined in this study, combined with the weighted center of injection timing defined in the previous literature, was found well suited to characterize multiple injection strategies, including the effects of the number of injections, fuel mass in each injection and the dwell time between injections.

Experimental investigations on combustion of jatropha methyl ester in a turbocharged direct-injection diesel engine

2008 ◽  
Vol 222 (10) ◽  
pp. 1865-1877 ◽  
Author(s):  
K Anand ◽  
R P Sharma ◽  
P S Mehta
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Peak Pressure ◽  
Direct Injection ◽  
Pressure Rise ◽  
Experimental Investigations ◽  
Injection Timing ◽  
Gas Temperature

Suitability of vegetable oil as an alternative to diesel fuel in compression ignition engines has become attractive, and research in this area has gained momentum because of concerns on energy security, high oil prices, and increased emphasis on clean environment. The experimental work reported here has been carried out on a turbocharged direct-injection multicylinder truck diesel engine using diesel fuel and jatropha methyl ester (JME)-diesel blends. The results of the experimental investigation indicate that an increase in JME quantity in the blend slightly advances the dynamic fuel injection timing and lowers the ignition delay compared with the diesel fuel. A maximum rise in peak pressure limited to 6.5 per cent is observed for fuel blends up to 40 per cent JME for part-load (up to about 50 per cent load) operations. However, for a higher-JME blend, the peak pressures decrease at higher loads remained within 4.5 per cent. With increasing proportion of JME in the blend, the peak pressure occurrence slightly advances and the maximum rate of pressure rise, combustion duration, and exhaust gas temperature decrease by 9 per cent, 15 per cent and 17 per cent respectively. Although the changes in brake thermal efficiencies for 20 per cent and 40 per cent JME blends compared with diesel fuel remain insignificant, the 60 per cent JME blend showed about 2.7 per cent improvement in the brake thermal efficiency. In general, it is observed that the overall performance and combustion characteristics of the engine do not alter significantly for 20 per cent and 40 per cent JME blends but show an improvement over diesel performance when fuelled with 60 per cent JME blend.

Study And Evaluation of Injection Timing of CIDI Engine Injection Pump Using Alternate Fuel i.e Biodiesel Fuel

2016 ◽  
Vol 8 (01) ◽  
pp. 11-19
Author(s):  
P. K. Singh ◽  
Rohit K. Shrivastava ◽  
K. G. Sinha
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Gas Temperature ◽  
Engine Exhaust ◽  
Brake Thermal Efficiency ◽  
Injection Pump ◽  
Alternate Fuel ◽  
Exhaust Gas Temperature

In this investigation an experimental study of the effects of FIP injection timing on Specific Fuel Consumption(SFC), Brake Thermal Efficiency(BTE), Engine Exhaust Gas Temperature(EEGT), CO, HC, NOX and Smoke of “Kirloskar- 6R1080TA, 6-CylinderInline, Direct Injection, Turbocharged Intercooled, 191 hp Diesel Engine” has been conducted. Injection Timing retardation method has been utilised to reduce SFC, EEGT, CO, HC, NOX, Smoke and increase BTE of Kirloskar-6R1080TA Diesel Engine. The Kirloskar 6R1080TA engine has been tested for six different injection timings (23°, 21°, 20°, 19°, 18° and 17° CA BTC) at same engine speeds and load conditions. The SFC,EEGT, CO, HC, NOX and Smoke of engine are approximately higher and BTE lower for injection timings at 23°, 21°, 20°, 18° and 17° CA BTC than 19° CA BTC at same speed and load. The results are showing that SFC,EEGT,CO,HC,NOX and Smoke are approximately reduces and BTE increases by reducing injection timing from 23° CA BTC to 19° CA BTC. Optimum FIP injection timing for Kirloskar 6R1080TA engine has been achieved at 19° CA BTC.

Cylinder Pressure Information-Based Postinjection Timing Control for Aftertreatment System Regeneration in a Diesel Engine—Part II: Active Diesel Particulate Filter Regeneration

2016 ◽  
Vol 138 (8) ◽  
Author(s):  
Hyunjun Lee ◽  
Jaesik Shin ◽  
Manbae Han ◽  
Myoungho Sunwoo
Keyword(s):  
Diesel Particulate Filter ◽  
Fuel Injection ◽  
Control Method ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Cylinder Pressure ◽  
Gas Temperature ◽  
Diesel Particulate ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

The successful utilization of a diesel particulate filter (DPF) to reduce particulate matter (PM) in a passenger car diesel engine necessitates a periodic regeneration of the DPF catalyst without deterioration of the drivability and emission control performance. For successful active DPF regeneration, the exhaust gas temperature should be over 500 °C to oxidize the soot loaded in the DPF. Previous research increased the exhaust gas temperature by applying early and late post fuel injection with a look-up table (LUT) based feedforward control implemented into the engine management system (EMS). However, this method requires enormous calibration work to find the optimal timing and quantity of the main, early, and late post fuel injection with less certainty of accurate torque control. To address this issue, we propose a cylinder pressure based multiple fuel injection (MFI) control method for active DPF regeneration. The feedback control of the indicated mean effective pressure (IMEP), lambda, and DPF upstream temperature was applied to precisely control the injection quantity of the main, early, and late post fuel injection. To determine their fuel injection timings, a mass fraction burned 60% after location of the rate of heat release maximum (MFB60aLoROHRmax) was proposed based on the cylinder pressure information. The proposed control method was implemented in an in-house EMS and validated at several engine operating conditions. During the regeneration period, the exhaust gas temperature tracked the desired temperature, and the engine torque fluctuation was minimized with minimal PM and NOx emissions.

scholarly journals The effect of alternative fuels injection timing on toxic substances formation in CI engines

2017 ◽  
Vol 168 (1) ◽  
pp. 73-76
Author(s):  
Marcin WOJS ◽  
Piotr ORLIŃSKI ◽  
Jakub LASOCKI
Keyword(s):  
Diesel Fuel ◽  
Alternative Fuels ◽  
Fuel Injection ◽  
Combustion Process ◽  
Acid Methyl Ester ◽  
Operating Conditions ◽  
Injection Timing ◽  
Toxic Substances ◽  
Important Conclusion ◽  
Ci Engines

The present study describes selected issues associated with the emission level in toxic exhaust gases and fuel injection timing. The study was focused on the following types of fuels: Diesel oil (the base fuel) and the other fuels were the mixture of fatty acid methyl ester with Camelina (L10 – diesel fuel with 10% V/V FAME of Camelina and L20 – diesel fuel with 10% V/V FAME of Camelina) was used. Fuel injection advanced angle was set for three different values – the factory setting – 12° before TDC, later injection – 7° and earlier injection – 17°. The most important conclusion is that in most measurement points registered in the same engine operating conditions, the concentration of fuel NOx in L10 and L20 increased but PM emissions decreased which is caused by active oxygen located in the internal structure of the fuel. This fact contributes to the rise in temperature during the combustion process. At the same time factory settings of the angle makes NOx emissions lower and close to reference fuel.

Sign in / Sign up

Export Citation Format

Share Document