scholarly journals Experimental Campaign Tests on a Tesla Micro-Expanders

2019 ◽  
Vol 113 ◽  
pp. 03015 ◽  
Author(s):  
Avinash Renuke ◽  
Alberto Traverso ◽  
Matteo Pascenti
Keyword(s):  
Experimental Analysis ◽  
Rotational Speed ◽  
Compressed Air ◽  
Working Fluid ◽  
Experiment System ◽  
Disk Thickness ◽  
Experimental Campaign ◽  
Power Group ◽  
Speed Up ◽  
The Impact

This paper presents the experimental campaign on Tesla turbo expanders carried out at Thermo-chemical Power group (TPG) of University of Genoa, Italy. An experiment system is established using compressed air as a working fluid. A 200 W turbine is tested with rotational speed up to 40000 rpm. Experimental analysis focused mainly on the efficiency features of this expander, showing the impact on performance of different disk gaps, disk thickness, discharge holes, exhaust geometry, as a function of speed and mass flow. An improved version of 3 kW air Tesla turboexpander is built. Preliminary experimental results are discussed along with the effect of number of nozzles on the performance of the turbine.

Experimental study of thermohydraulic characteristics and irreversibility analysis of novel axial corrugated tube with spring tape inserts

2020 ◽  
Vol 92 (3) ◽  
pp. 30901
Author(s):  
Suvanjan Bhattacharyya ◽  
Debraj Sarkar ◽  
Ulavathi Shettar Mahabaleshwar ◽  
Manoj K. Soni ◽  
M. Mohanraj
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Thermal Performance ◽  
Working Fluid ◽  
The Novel ◽  
Heat Exchanger Tube ◽  
Heat Transfer Augmentation ◽  
Corrugated Tube ◽  
The Impact ◽  
Exchanger Tube

The current study experimentally investigates the heat transfer augmentation on the novel axial corrugated heat exchanger tube in which the spring tape is introduced. Air (Pr = 0.707) is used as a working fluid. In order to augment the thermohydraulic performance, a corrugated tube with inserts is offered. The experimental study is further extended by varying the important parameters like spring ratio (y = 1.5, 2.0, 2.5) and Reynolds number (Re = 10 000–52 000). The angular pitch between the two neighboring corrugations and the angle of the corrugation is kept constant through the experiments at β = 1200 and α = 600 respectively, while two different corrugations heights (h) are analyzed. While increasing the corrugation height and decreasing the spring ratio, the impact of the swirling effect improves the thermal performance of the system. The maximum thermal performance is obtained when the corrugation height is h = 0.2 and spring ratio y = 1.5. Eventually, correlations for predicting friction factor (f) and Nusselt number (Nu) are developed.

scholarly journals Computer Model for Financial, Environmental and Risk Analysis of a Wind–Diesel Hybrid System with Compressed Air Energy Storage

Energies ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 4054 ◽  
Author(s):  
Youssef Benchaabane ◽  
Rosa Elvira Silva ◽  
Hussein Ibrahim ◽  
Adrian Ilinca ◽  
Ambrish Chandra ◽  
...  
Keyword(s):  
Risk Assessment ◽  
Renewable Energy ◽  
Energy Storage ◽  
Environmental Impact ◽  
Hybrid System ◽  
Computer Model ◽  
Net Present Value ◽  
Compressed Air ◽  
Compressed Air Energy Storage ◽  
The Impact

Remote and isolated communities in Canada experience gaps in access to stable energy sources and must rely on diesel generators for heat and electricity. However, the cost and environmental impact resulting from the use of fossil fuels, especially in local energy production, heating, industrial processes and transportation are compelling reasons to support the development and deployment of renewable energy hybrid systems. This paper presents a computer model for economic analysis and risk assessment of a wind–diesel hybrid system with compressed air energy storage. The proposed model is developed from the point of view of the project investor and it includes technical, financial, risk and environmental analysis. Robustness is evaluated through sensitivity analysis. The model has been validated by comparing the results of a wind–diesel case study against those obtained using HOMER (National Renewable Energy Laboratory, Golden, CO, United States) and RETScreen (Natural Resources Canada, Government of Canada, Canada) software. The impact on economic performance of adding energy storage system in a wind–diesel hybrid system has been discussed. The obtained results demonstrate the feasibility of such hybrid system as a suitable power generator in terms of high net present value and internal rate of return, low cost of energy, as well as low risk assessment. In addition, the environmental impact is positive since less fuel is used.

Altitude Effects on the Performance of Small Radial Turbomachinery: Part I — Compressor Impellers

2016 ◽  
Author(s):  
Dries Verstraete ◽  
Kjersti Lunnan
Keyword(s):  
Reynolds Number ◽  
Performance Analysis ◽  
Rotational Speed ◽  
Pressure Ratio ◽  
Unmanned Aircraft ◽  
Good Match ◽  
One Dimensional ◽  
Design Changes ◽  
Current Article ◽  
The Impact

Small unmanned aircraft are currently limited to flight ceilings below 20,000 ft due to the lack of an appropriate propulsion system. One of the most critical technological hurdles for an increased flight ceiling of small platforms is the impact of reduced Reynolds number conditions at altitude on the performance of small radial turbomachinery. The current article investigates the influence of Reynolds number on the efficiency and pressure ratio of two small centrifugal compressor impellers using a one-dimensional meanline performance analysis code. The results show that the efficiency and pressure ratio of the 60 mm baseline compressor at the design rotational speed drops with 6–9% from sea-level to 70,000 ft. The impact on the smaller 20 mm compressor is slightly more pronounced and amounts to 6–10%. Off-design changes at low rotational speeds are significantly higher and can amount to up to 15%. Whereas existing correlations show a good match for the efficiency drop at the design rotational speed, they fail to predict efficiency changes with rotational speed. A modified version is therefore proposed.

An experimental analysis of the impact of campaign polls on electoral information seeking

2015 ◽  
Vol 40 ◽  
pp. 146-157 ◽  
Author(s):  
Jason Roy ◽  
Shane P. Singh ◽  
Patrick Fournier ◽  
Blake Andrew
Keyword(s):  
Experimental Analysis ◽  
Information Seeking ◽  
The Impact

An Experimental Analysis of the Effects of Different Hardware Setups on Stereo Camera Systems

2021 ◽  
Vol 15 (03) ◽  
pp. 337-357
Author(s):  
Alexander Julian Golkowski ◽  
Marcus Handte ◽  
Peter Roch ◽  
Pedro J. Marrón
Keyword(s):  
Experimental Analysis ◽  
Autonomous Navigation ◽  
Indoor Environments ◽  
Camera System ◽  
Stereo Camera ◽  
Camera Systems ◽  
Sensing Technology ◽  
Stereo Cameras ◽  
The Impact ◽  
General Guidance

For many application areas such as autonomous navigation, the ability to accurately perceive the environment is essential. For this purpose, a wide variety of well-researched sensor systems are available that can be used to detect obstacles or navigation targets. Stereo cameras have emerged as a very versatile sensing technology in this regard due to their low hardware cost and high fidelity. Consequently, much work has been done to integrate them into mobile robots. However, the existing literature focuses on presenting the concepts and algorithms used to implement the desired robot functions on top of a given camera setup. As a result, the rationale and impact of choosing this camera setup are usually neither discussed nor described. Thus, when designing the stereo camera system for a mobile robot, there is not much general guidance beyond isolated setups that worked for a specific robot. To close the gap, this paper studies the impact of the physical setup of a stereo camera system in indoor environments. To do this, we present the results of an experimental analysis in which we use a given software setup to estimate the distance to an object while systematically changing the camera setup. Thereby, we vary the three main parameters of the physical camera setup, namely the angle and distance between the cameras as well as the field of view and a rather soft parameter, the resolution. Based on the results, we derive several guidelines on how to choose the parameters for an application.

STUDY ON THE PROCESS OF RAPESEED HULLING BY THE IMPACT

2019 ◽  
Author(s):  
А.О. РЕНЗЯЕВ ◽  
О.П. РЕНЗЯЕВ ◽  
С.Н. КРАВЧЕНКО ◽  
Р.В. КРЮК
Keyword(s):  
Rotational Speed ◽  
Calculated Data ◽  
Quality Characteristics ◽  
Complete Separation ◽  
Edible Oil ◽  
Siberian Region ◽  
The Core ◽  
The Cost ◽  
The Impact

Исследованы прочностные и физико-механические свойства оболочки рапса с точки зрения ее разрушения и удаления. Установлено, что наиболее рациональным является двухстадийный способ обрушивания: 1-я стадия – на вальцовых мельницах, 2-я – на центробежной обрушивающей машине. Определены параметры центробежной обрушивающей машины для обеспечения минимальной необходимой линейной скорости 10,81 м/с: угол наклона отбойной пластины (90 ± 2)°, частота вращения барабана (2400 ± 150) об/мин. Установлено, что правильно подобранные условия и угол, под которым происходит удар, позволяют значительно снизить количество не до конца обрушенного семени и содержание расколотого ядра. При этом при свободном ударе об отбойную пластину под углом, отличным от 88–91°, или подаче недостаточно равномерного потока семян значительно увеличивается содержание необрушенных семян. На разрушение 1 кг семян необходимо затратить 58,45 Дж. Таким образом, по расчетным данным, для семян рапса диаметром 1,5 мм частота вращения барабана должна находиться в диапазоне от 2221 до 2565 об/мин при ударе семени под углом 90°. Диаметр семян рапса, выращиваемого в Сибирском регионе, составляет от 0,8 до 1,8 мм. Установлено, что подсушивание семян рапса в течение 30–40 с при температуре 100°С позволяет увеличить эффективность разрушения оболочки до полного ее отделения от ядра рапса. Представленные результаты позволяют повысить качество очистки семян рапса от оболочки и улучшить качественные характеристики получаемого масла, облегчить последующие технологические процессы получения пищевого масла, снизить затраты на рафинацию и дезодорацию на 2%. The strength and physico-mechanical properties of the shell of rapeseed in terms of its destruction and removal are investigated. It is established that the most rational is a two-stage method of seed hulling: the 1st stage – on roller mills, the 2nd – on a centrifugal hulling machine. The parameters of the centrifugal hulling machine to provide the minimum required linear speed of 10,81 m/s are defined: the angle of inclination of the turnback plate (90 ± 2)°, the rotational speed of drum (2400 ± 150) RPM. It is established that the correctly selected conditions and the angle at which the impact occurs, can significantly reduce the amount is not completely hulling seed and the substance of the split nucleus. At the same time, with a free impact on the turnback plate at an angle different from 88–91°, or the supply of an insufficiently uniform flow of seeds, the content is not completely hulling seed increases significantly. On hulling of 1 kg of seeds it is necessary to spend 58,45 J. Thus, according to the calculated data, for rape seeds with a diameter of 1,5 mm, the rotational speed of drum should be in the range from 2221 to 2565 RPM when the seed is struck at an angle of 90°. The diameter of rapeseed grown in the Siberian region ranges from 0,8 to 1,8 mm. It was found that drying of rapeseed for 30–40 s at a temperature of 100°C, can increase the efficiency of destruction of the shell to its complete separation from the core of rapeseed. The presented results make it possible to improve the quality of cleaning of rape seeds from the shell and improve the quality characteristics of the obtained oil, facilitate the subsequent technological processes of obtaining edible oil, reduce the cost of refining and deodorization by 2%.

Effect of Buoyancy and Density Ratio on Heat Transfer in a Smooth Cooling Channel of a Gas Turbine Blade

2018 ◽  
Author(s):  
Mandana S. Saravani ◽  
Saman Beyhaghi ◽  
Ryoichi S. Amano
Keyword(s):  
Heat Transfer ◽  
Rotational Speed ◽  
Cfd Simulation ◽  
Density Ratio ◽  
Reynolds Numbers ◽  
Buoyancy Effect ◽  
Square Channel ◽  
First Case ◽  
Computational Fluid Dynamics Cfd ◽  
The Impact

The present work investigates the effects of buoyancy and density ratio on the thermal performance of a rotating two-pass square channel. The U-bend configuration with smooth walls is selected for this study. The channel has a square cross-section with a hydraulic diameter of 5.08 cm (2 inches). The lengths of the first and second passes are 514 mm and 460 mm, respectively. The turbulent flow enters the channel with Reynolds numbers of up to 34,000. The rotational speed varies from 0 to 600 rpm with the rotational numbers up to 0.75. For this study, two approaches are considered for tracking the buoyancy effect on heat transfer. In the first case, the density ratio is set constant, and the rotational speed is varied. In the second case, the density ratio is changed in the stationary case, and the effect of density ratio is discussed. The range of Buoyancy number along the channel is 0–6. The objective is to investigate the impact of Buoyancy forces on a broader range of rotation number (0–0.75) and Buoyancy number scales (0–6), and their combined effects on heat transfer coefficient for a channel with aspect ratio of 1:1. Several computational fluid dynamics (CFD) simulation are carried out for this study, and some of the results are validated against experimental data.

scholarly journals The impact of rotational speed and water volume on textile translational motion in a front-loading washer

2018 ◽  
Vol 89 (16) ◽  
pp. 3401-3410 ◽  
Author(s):  
Hong Liu ◽  
R Hugh Gong ◽  
Pinghua Xu ◽  
Xuemei Ding ◽  
Xiongying Wu
Keyword(s):  
Residence Time ◽  
Rotational Speed ◽  
High Speed ◽  
Translational Motion ◽  
Processing System ◽  
Water Volume ◽  
Motion Path ◽  
Rotational Axis ◽  
Passive Region ◽  
The Impact

Textile motion in a front-loading washer has been characterized via video capturing, and a processing system developed based on image geometric moment. Textile motion significantly contributes to the mass transfer of the wash solution in porous materials, particularly in the radial direction (perpendicular to the rotational axis of the inner drum). In this paper, the velocity profiles and residence time distributions of tracer textiles have been investigated to characterize the textile dynamics in a front-loading washer. The results show that the textile motion varies significantly with the water volume and rotational speed, and that the motion path follows certain patterns. Two regions are observed in the velocity plots: a passive region where the textile moves up with low velocity and an active region where the textile falls down with relatively high speed. A stagnant area in the residence time profile is observed. This corresponds to the passive region in the velocity profile. The stagnant area affects the mechanical action, thus influencing washing efficiency and textile performance. The findings on textile dynamics will help in the development of better front-loading washers.

scholarly journals Performance analysis of the thermoacoustic refrigerator with the standing wave and air as a working fluid

2018 ◽  
Vol 44 ◽  
pp. 00063 ◽  
Author(s):  
Jakub Kajurek ◽  
Artur Rusowicz
Keyword(s):  
Temperature Difference ◽  
High Reliability ◽  
Power Input ◽  
Acoustic Power ◽  
Operating Frequency ◽  
Working Fluid ◽  
Resonator Length ◽  
Environmental Friendliness ◽  
The Impact ◽  
Thermoacoustic Refrigerator

Thermoacoustic refrigerator is a new and emerging technology capable of transporting heat from a low-temperature source to a high-temperature source by utilizing the acoustic power input. These devices, operating without hazardous refrigerants and owning no moving components, show advantages of high reliability and environmental friendliness. However, simple to fabricate, the designing of thermoacoustic refrigerators is very challenging. This paper illustrates the impact of significant factors on the performance of the thermoacoustic refrigerator which was measured in terms of the temperature difference generated across the stack ends. The experimental device driven by a commercial loudspeaker and air at atmospheric pressure as a working fluid was examined under various resonator length and operating frequencies. The results indicate that appropriate resonator’s length and operating frequency lead to an increase in the temperature difference created across the stack. The maximum values were achieved for operating frequency equalled to 200 and 300 Hz whereas resonator length corresponded to the half-length of the acoustic wave for these frequencies. The results of experiment also confirm that relationship between these parameters is strongly affected by the stack spacing, which in this research was equalled to 0.4 mm.

scholarly journals Investigations of Inducers Operating With High Rotational Speed

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Björn Gwiasda ◽  
Matthias Mohr ◽  
Martin Böhle
Keyword(s):  
Rotational Speed ◽  
Test Bench ◽  
Pressure Rise ◽  
Working Fluid ◽  
Cfd Simulations ◽  
High Rotational Speed ◽  
Rotating Speed ◽  
Performance Pressure ◽  
Computational Fluid Dynamics Cfd ◽  
Suction Performance

Suction performance, pressure rise, and efficiency for four different inducers are examined with computational fluid dynamics (CFD) simulations and experiments performed with 18,000 rpm and 24,000 rpm. The studies originate from a research project that includes the construction of a new test bench in order to judge the design of the different inducers. This test bench allows to conduct experiments with a rotational speed of up to 40,000 rpm and high pressure ranges from 0.1 bar to 40 bar with water as working fluid. Experimental results are used to evaluate the accuracy of the simulations and to gain a better understanding of the design parameter. The influence of increasing the rotating speed from 18,000 rpm to 24,000 rpm on the performance is also shown.

Sign in / Sign up

Export Citation Format

Share Document