scholarly journals Study on the variation of physical and mechanical characteristics under freeze-thaw condition

2020 ◽  
Vol 165 ◽  
pp. 03021
Author(s):  
Tian Yanzhe
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Physical And Mechanical Properties ◽  
Peak Stress ◽  
Friction Angle ◽  
Confining Pressure ◽  
Freeze Thaw ◽  
Triaxial Compressive Strength

Subjected to freeze-thaw cycles, the deformation of physical and mechanical properties is the main cause of engineering disasters. Based on the analysis of the results of triaxial compression test after different freeze-thaw cycles, conclusions are drawn that: under the certain freeze-thaw cycles conditions, with the increase of confining pressure, the triaxial compressive strength, elastic modulus and the axial strain increase gradually, indicating that the failure of rock changes from brittle failure to plastic failure; in the case of same confining pressure, with the increase of the number of freeze-thaw cycles, the triaxial compressive strength,elastic modulus of rock decreases and the axial strain corresponding to peak stress gradually increase. With the increase of the number of freeze-thaw cycles, the cohesion of grit is in the form of exponentially decays to reduce,the internal friction angle changes very little.

scholarly journals Mechanical Characteristics of Coal Samples under Triaxial Unloading Pressure with Different Test Paths

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Yang Zhang ◽  
Yongjie Yang ◽  
Depeng Ma
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Axial Loading ◽  
Peak Stress ◽  
Friction Angle ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Compression Tests ◽  
Leading Role ◽  
Unloading Rate

In order to understand the influence of unloading path on the mechanical properties of coal, triaxial unloading confining pressure tests with different initial confining pressure and different unloading rate were carried out. The test results show that the triaxial unloading strength of coal samples under different test conditions is lower than conventional triaxial tests, but the brittleness characteristics are more obvious. This result indicates that the coal samples are easily damaged under unloading conditions. In the axial loading stage of the confinement unloading tests, the axial strain plays a leading role. However, during the confining pressure unloading stage, the circumferential deformation is large, which is the main deformation in this stage. Higher unloading rates of confining pressure are associated with shorter times between the peak stress position and sample complete failure. This shows that samples are more easily destroyed under higher unloading rates and the samples are more difficultly destroyed under lower unloading rates. In addition, with increasing unloading rate, the peak principal stress difference and confining pressure at failure decrease gradually, whereas the confining pressure difference at failure increases gradually. Compared with conventional triaxial compression tests, the cohesion of coal is reduced and the internal friction angle is increased under the condition of triaxial unloading test.

scholarly journals Experimental Study on the Mechanical Properties of Sandstone under the Action of Chemical Erosion and Freeze-Thaw Cycles

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Lizhuang Cui ◽  
Nan Qin ◽  
Shuai Wang ◽  
Xuezhi Feng
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Triaxial Compression ◽  
Rock Properties ◽  
Chemical Solution ◽  
Compression Tests ◽  
Chemical Erosion ◽  
Freeze Thaw ◽  
The Impact

In order to study the mechanical properties of sandstone under the coupling action of chemical erosion and freeze-thaw cycles, the fine-grained yellow sandstone in a mining area in Zigong, China, is collected as the research object. The changes in mechanical properties of yellow sandstone under the coupling action of chemical solution erosion and freeze-thaw cycles are analyzed based on uniaxial compression tests (UCTs) and triaxial compression tests (TCTs). The results show that, with the increase in freeze-thaw cycles, the compressive strength, elastic modulus, and cohesion of the sandstone samples decrease with varying degrees. Under constant freeze-thaw cycles, the most serious mechanical properties of degradation are observed in acidic solution, followed by alkaline solution and neutral solution. Under different confining pressures, the compressive strength and elastic modulus of the sandstone samples decrease exponentially with the increase in freeze-thaw cycles. Under the action of the chemical solution erosion and freeze-thaw cycles, the internal friction angle fluctuates around 30°. For the cohesion degradation, 35.4%, 29.3%, and 27.2% degradation are observed under acidic, alkaline, and neutral solutions. Nuclear magnetic resonance imaging shows that the chemical erosion and freeze-thaw cycles both promote the degradation of rock properties from surface to interior; after 45 freeze-thaw cycles, the mechanical properties drop sharply. To properly design rock tunneling support and long-term protection in the cold region, the impact of both freeze-thaw cycles and chemical erosion should be considered.

scholarly journals Physical and Mechanical Properties of Gypsum-Like Rock Materials

2020 ◽  
Vol 2020 ◽  
pp. 1-17 ◽  
Author(s):  
Sijiang Wei ◽  
Chongyang Wang ◽  
Yushun Yang ◽  
Meng Wang
Keyword(s):  
High Temperature ◽  
Internal Friction ◽  
Triaxial Compression ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Friction Angle ◽  
Confining Pressure ◽  
Peak Intensity ◽  
Saturated Sample ◽  
Gypsum Rock

In the process of tunnel construction, gypsum rock is often encountered, and the volume of gypsum rock expands when encountering water, which is easy to cause the occurrence of rock fall, collapse, and other disasters, bringing serious challenges to the safe construction of the tunnel. Therefore, in this paper, four groups of samples under different moisture content are tested by ultrasonography, uniaxial compression, conventional triaxial compression, Brazilian splitting, X-ray diffraction, and SEM, and then the physical and mechanical properties of gypsum rock are studied, and the conclusion is as follows: the density of the water saturated sample, and the longitudinal wave velocity of the natural sample are the highest. Both the water saturation and dehydration conditions have a weakening effect on the remolded sample of high-strength gypsum powder. The peak intensity of the sample gradually increases with the increase of confining pressure, and the relationship between the peak intensity and confining pressure of the sample conforms to the Coulomb strength criterion. After high-temperature dehydration, the sample showed obvious plastic softening characteristics. The cohesion and internal friction angle of the sample are closely related to the water content. The cohesion is the largest in the 45°C dehydrated sample, the internal friction angle is the smallest in the saturated sample, whereas the cohesion is the smallest and internal friction is the largest in the high-temperature dehydrated sample. The characteristics of failure for the natural and 45°C dehydrated samples are almost the same and most samples show shear or shear-tensile failure. The shear plane begins at the edge of the end face of the sample and exhibits a typical diagonal shear failure. The high-temperature dehydrated samples are completely broken under uniaxial and triaxial compression conditions. After high-strength gypsum powder was used to make the remolded sample, the calcium sulfate disappeared, the water content increased, and the main mineral components of the natural and saturated samples were the same. After dehydration at 45°C, the sample began to release structural water and generate SiO2. After high-temperature dehydration, the hemihydrate gypsum continued to dehydrate and become soluble anhydrous gypsum.

scholarly journals Sealing Performance of New Solidified Materials: Mechanical Properties and Stress Sensitivity Characterization of Pores

2020 ◽  
Vol 2020 ◽  
pp. 1-16
Author(s):  
Chao Zhang ◽  
Gaohan Jin ◽  
Chao Liu ◽  
Shugang Li ◽  
Junhua Xue ◽  
...  
Keyword(s):  
Coal Sample ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Peak Stress ◽  
Confining Pressure ◽  
Stress Sensitivity ◽  
Test System ◽  
Sample Material ◽  
Sealing Material ◽  
The Difference

Borehole-sealing solidified material plays a significant role in improving sealing quality and enhancing gas drainage performance. In this study, the MTS815 electro-hydraulic triaxial servo test system and MR-60 NMR test system were adopted to conduct triaxial compression control experiment on the coal sample material, concrete material, and new solidified sealing material, respectively. This paper aims to analyze the difference of support effects, porosity, and stress sensitivity between those materials. Experimental results show that under the same stress condition, the stiffness of traditional concrete solidified material is the largest, while the new solidified material is the second, and the coal sample material is the smallest. Compared with the traditional concrete solidified material, the new solidified sealing material has better strain-bearing capacity and volumetric expansion capacity under each confining pressure in the experiment. The axial strain and volume increment of new solidified material is higher than those of the traditional concrete solidified material at the peak stress. Meanwhile, the confining pressure has a certain hysteresis effect on the postpeak stress attenuation. Fracture has the strongest stress sensitivity in three pore types, and its T2 map relaxation area has a larger compression than adsorption pore and seepage pore under the same pressure. The relative content of seepage pore and fracture in the new solidified material is less than that of coal and concrete samples, and the stress sensitivity of the new solidified materials is weaker than that of coal and concrete materials, thence, new solidified material will have better performance in borehole sealing. Outcomes of this study could provide guidance on the selection of the most effective sealing materials for sealing-quality improvement.

Performance Comparison between High Strength Concrete and Ordinary Concrete under Mixed Erosion and Freeze-Thaw Cycling

2010 ◽  
Vol 163-167 ◽  
pp. 1667-1672
Author(s):  
Jian Zhang ◽  
Bo Diao ◽  
Yan Dong Li ◽  
Xiao Ning Zheng
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
High Strength Concrete ◽  
Mass Loss Rate ◽  
Peak Stress ◽  
High Strength ◽  
Performance Comparison ◽  
Freeze Thaw ◽  
Strength Concrete ◽  
Ordinary Concrete

: Performance of high strength concrete and ordinary concrete under alternating action of mixed erosion and freeze-thaw cycling were compared. The erosion solution was mixed by weight of 3% sodium chloride and 5% sodium sulfate. Results showed that, after 200 freeze-thaw cycles, the effect of surface scaling of ordinary concrete was more significant than that of high strength concrete, and the mass loss rate of ordinary concrete was much higher; The relative dynamic modulus of elasticity of high strength concrete slightly increased by 2.99%, while that of ordinary concrete decreased more than 13%. Compressive strength and elastic modulus of high strength and ordinary concrete behaved almost in the same way in the first 50 freeze-thaw cycles, with the increase of freeze-thaw cycles in the following test, the compressive strength and elastic modulus of ordinary concrete showed larger reductions than these of high strength concrete. As the freeze-thaw cycles increased, the corresponding strain to the peak stress of high strength concrete decreased, but it increased for ordinary concrete.

scholarly journals Experimental Investigation on Permeability Evolution of Dolomite Caprock under Triaxial Compression

Energies ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 6535
Author(s):  
Deng Xu ◽  
Jianfeng Liu ◽  
Zhide Wu ◽  
Lu Wang ◽  
Hejuan Liu ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Test Machine ◽  
Permeability Evolution ◽  
Triaxial Compressive Strength ◽  
Confining Pressures ◽  
Porosity And Permeability ◽  
The Difference ◽  
Maximum Permeability

In order to study the influence of different confining pressures on the stability and airtightness of dolomite underground gas storage, a permeability test under hydrostatic confining pressure, conventional triaxial compression test and gas–solid coupling test under triaxial compression were carried out on MTS815 test machine. During the tests, an acoustic emission (AE) monitoring system was also employed to estimate the rock damage. The experimental results showed that the relationships between permeability, porosity and hydrostatic confining pressure were exponential function and power function, respectively. Increasing confining pressure reduced the porosity and permeability of dolomite, and increased its triaxial compressive strength, but the addition of nitrogen reduced the compressive strength of dolomite by 10~30%, the higher the confining pressure, the smaller the difference. Compared with the maximum permeability under 15 MPa, confining pressure in the gas–solid coupling experiment, the maximum permeability under confining pressure of 30, 45, and 60 MPa is reduced by 42.0%, 84.4%, and 97.9%, respectively. In addition, the AE activity of dolomite decreases significantly with the increase in confining pressure, which also delayed the arrival of the AE active period.

scholarly journals Comparative Analyses Concerning Triaxial Compressive Yield Criteria of Coal with the Presence of Pore Water

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-15 ◽  
Author(s):  
Rulin Liu ◽  
Yanbin Yu ◽  
Weimin Cheng ◽  
Qingfeng Xu ◽  
Haotian Yang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Uniaxial Compressive Strength ◽  
Pore Water ◽  
Yield Criterion ◽  
Triaxial Compression ◽  
Strength Criterion ◽  
Confining Pressure ◽  
Quadratic Polynomial ◽  
Yield Criteria ◽  
Triaxial Compressive Strength

The least absolute deviation is used as a metric to analyze the applicability of five yield criteria, to describe the yield characteristics of coal based on triaxial compressive strength tests on natural, water-saturated, and seepage coal samples with the presence of pore water. The results show that the strength of coal exhibits nonlinear characteristics with the increase of confining pressure, which the linear Coulomb criterion fails to authentically describe. Although the parabolic Mohr criterion can describe the nonlinearity feature more decently than the linear yield criterion, the fitting error is significant, and the uniaxial compressive strength of coal is overestimated. The Hoek-Brown criterion, quadratic polynomial criterion, and exponential criterion yield decent fitting quality for the coal rock. In particular, the exponential strength criterion can accurately reflect the actual uniaxial compressive strength of the rock. However, the differential principle yield stress for an infinite confining pressure calculated from the exponential strength criterion is lower than the measured value. Furthermore, by employing effective stress principle to analyze the yield criteria for the saturated and seepage coal samples, one can find that the quadratic polynomial criterion and the exponential criterion can also reflect the changes of yield characteristics during the fluid-solid coupling triaxial compression test.

scholarly journals Effects of Long-Term Freeze–Thaw Cycles on the Properties of Stabilized/Solidified Lead-Zinc-Cadmium Composite-Contaminated Soil

2021 ◽  
Vol 18 (11) ◽  
pp. 6114
Author(s):  
Zhongping Yang ◽  
Jiazhuo Chang ◽  
Yao Wang ◽  
Xuyong Li ◽  
Shu Li
Keyword(s):  
Compressive Strength ◽  
Contaminated Soil ◽  
Triaxial Compression ◽  
Soil Column ◽  
Column Leaching ◽  
Freeze Thaw ◽  
Triaxial Compressive Strength ◽  
Zinc Cadmium ◽  
Lead Zinc

Lead, zinc, and cadmium were used to prepare a composite-contaminated soil to replicate common situations, in which soil is usually simultaneously contaminated by multiple metals. To examine the long-term durability of stabilized/solidified (S/S) contaminated soil, specimens were subjected to a series of freeze–thaw (F-T) cycles, up to ninety times (one day per cycle), prior to testing. Triaxial compression tests, soil column leaching tests, and X-ray diffraction analysis were then employed to study the mechanical properties, environmental influences, and micro-mechanisms of the S/S lead-zinc-cadmium composite-contaminated soils after long-term F-T. The results showed that triaxial compressive strength increases within three F-T cycles, then decreases before slightly increasing or stabilizing after thirty F-T cycles. The stage of decreased cohesion thus occurs between three and fourteen F-T cycles, with variation in other factors similar to that of the triaxial compressive strength. The cohesion mainly increases between three and seven cycles. The soil column leaching test showed that the permeability of soil is more than four times higher than that of soil not subject to freeze–thaw cycles after ninety F-T cycles. XRD tests further revealed that the chemical composition of S/S contaminated soil and the occurrence of each heavy metal (HM) remained unchanged under F-T treatment.

scholarly journals Mechanical and Failure Criteria of Air-Entrained Concrete under Triaxial Compression Load after Rapid Freeze-Thaw Cycles

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Feng-kun Cui ◽  
Huai-shuai Shang ◽  
Tie-jun Zhao ◽  
Guo-xi Fan ◽  
Guo-sheng Ren
Keyword(s):  
Compressive Strength ◽  
Uniaxial Compressive Strength ◽  
Stress Ratio ◽  
Triaxial Compression ◽  
Complex Stress State ◽  
Experimental Results ◽  
Testing System ◽  
Freeze Thaw ◽  
Triaxial Compressive Strength ◽  
Air Entrained Concrete

The experiment study on the air-entrained concrete of 100 mm cubes under triaxial compression with different intermediate stress ratioα2=σ2D : σ3Dwas carried out using a hydraulic-servo testing system. The influence of rapid freeze-thaw cycles and intermediate stress ratio on the triaxial compressive strengthσ3Dwas analyzed according to the experimental results, respectively. The experimental results of air-entrained concrete obtained from the study in this paper and the triaxial compression experimental results of plain concrete got through the same triaxial-testing-system were compared and analyzed. The conclusion was that the triaxial compressive strength is greater than the biaxial and uniaxial compressive strength after the same rapid freeze-thaw cycles, and the increased percentage of triaxial compressive strength over biaxial compressive strength or uniaxial compressive strength is dependent on the middle stress. The experimental data is useful for precise analysis of concrete member or concrete structure under the action complex stress state.

scholarly journals Effect of freeze–thaw cycle on physical and mechanical properties and damage characteristics of sandstone

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Longxiao Chen ◽  
Kesheng Li ◽  
Guilei Song ◽  
Deng Zhang ◽  
Chuanxiao Liu
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Physical And Mechanical Properties ◽  
Freeze Thaw ◽  
Damage Characteristics ◽  
Large Pore ◽  
Natural Rock ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle

AbstractRock deterioration under freeze–thaw cycles is a concern for in-service tunnel in cold regions. Previous studies focused on the change of rock mechanical properties under unidirectional stress, but the natural rock mass is under three dimensional stresses. This paper investigates influences of the number of freeze–thaw cycle on sandstone under low confining pressure. Twelve sandstone samples were tested subjected to triaxial compression. Additionally, the damage characteristics of sandstone internal microstructure were obtained by using acoustic emission (AE) and mercury intrusion porosimetry. Results indicated that the mechanical properties of sandstone were significantly reduced by freeze–thaw effect. Sandstone’ peak strength and elastic modulus were 7.28–37.96% and 6.38–40.87% less than for the control, respectively. The proportion of super-large pore and large pore in sandstone increased by 19.53–81.19%. We attributed the reduced sandstone’ mechanical properties to the degenerated sandstone microstructure, which, in turn, was associated with increased sandstone macropores. The macroscopic failure pattern of sandstone changed from splitting failure to shear failure with an increasing of freeze–thaw cycles. Moreover, the activity of AE signal increased at each stage, and the cumulative ringing count also showed upward trend with the increase of freeze–thaw number.

Sign in / Sign up

Export Citation Format

Share Document