scholarly journals Effect of the sorting track profile change on the it’s occupancy quality at train humping

2018 ◽  
Vol 216 ◽  
pp. 02012 ◽  
Author(s):  
Konstantin Kornienko ◽  
Sergei Bessonenko
Keyword(s):  
Simulation Model ◽  
High Quality ◽  
Run Off ◽  
Profile Correction ◽  
Probability Of Collision ◽  
Profile Change

To increase the hump yard capacity, it is necessary to ensure high quality of sorting track occupancy. The purpose of this paper is to study the effect of changing the track profile on the quality of its occupancy. The simulation model developed for occupancy of sorting tracks based on the calculation of the speed of the cut and taking the following into consideration was used for the study: the possibility of starting the cut movement after a stop, errors in operation of the devices in charge of the speed of releasing the cut to the track, the possibility of displacement of the cars when the next cut collides with them. A real profile of the sorting facility track was analyzed as an example of it. It was determined that the profile caused strong effect on the track occupancy quality. The sagging of the profile causes an increase in the probability of collision of the cuts with exceeding the permissible speed. An increase in the up-gradient reduces the range of the run-off distance, which in turn causes an increase in the number of car back-ins. Profile correction will allow increasing the track occupancy quality.

Novel Dielectric Stack Actuators for Dynamic Applications

2012 ◽  
Author(s):  
Sven Herold ◽  
William Kaal ◽  
Tobias Melz
Keyword(s):  
Simulation Model ◽  
Surface Resistance ◽  
Design Concept ◽  
Metal Electrodes ◽  
High Quality ◽  
Complex Material ◽  
Simulation Results ◽  
Actuator Design ◽  
Load Conditions

In order to realize dielectric elastomer stack actuators suitable for dynamic applications a new actuator design with rigid, perforated electrodes is developed. The low surface resistance of the metal electrodes predestines this concept for dynamic applications where higher currents are present. Detailed numerical analyses are performed to show the potential of this approach, to study the complex material deformation and to optimize the aperture geometry. A multilayer stack actuator is then manufactured and characterized experimentally under various load conditions to gain suitable parameters for a parametrized model. It is subsequently used to attenuate vibrations of a truss structure. By careful adjusting the parameters it functions both as passive absober and as actuator. A comparison of experimental and simulation results proves the high quality of the simulation model. The work shows the great potential of the new design concept for future applications especially in the field of smart structures.

Validation of Shiphandling Simulation Models

2011 ◽  
Author(s):  
Tor E. Berg ◽  
Edvard Ringen
Keyword(s):  
Simulation Model ◽  
Numerical Models ◽  
Real Life ◽  
Simulation Models ◽  
Test Scheme ◽  
High Quality ◽  
Simulation Tools ◽  
Benchmark Study ◽  
Actual Application

This paper describes the need for improved methods for validating numerical models used in shiphandling simulators. Such models vary in complexity, from rather simplistic models used for initial shiphandling training at maritime training centers to high-quality models used in the study of advanced marine operations. High-quality simulation models are also used in investigations of maritime accidents such as collisions and groundings. The SIMMAN 2008 conference presented the results of benchmarking studies of simulation tools currently used by research institutes, universities and training centers around the world. Many of these tools employ models based on numerical calculations using methods based on potential or viscous fluid flow, experiments using scale ship models (free running or captive) or semi empirical expressions based on regression analysis of previous model tests. The organizers of SIMMAN 2008 made the hull characteristics of certain ship types available for a comparative study of simulation maneuvering models. The outcome of the benchmark study (using IMO standard maneuvers as case study maneuvers) showed that simulated results varied significantly. In the opinion of the authors, there is an urgent need for new validation studies. The first part of this paper discusses the concepts of simulation model fidelity, verification and validation and the present guidelines issued by ITTC for validation of maneuvering simulation models. The second part looks at the outcomes of the SIMMAN 2008 conference and describes MARINTEK’s contribution to the benchmark study. The use of real-world measurements in model validation is briefly discussed. The need for registration of actual test conditions, as well as the types of tests that should be included in a test scheme, are presented. Finally, the authors discuss validation requirements with respect to the actual application of the selected simulation model as an engineering tool that can be transferred to training simulators used by maritime training centers. It is assumed that simplified simulation models may reduce the quality of simulator based training for ship officers. It is believed that increased quality of simulator model will improve the transfer of training from simulators to real life operations and remove some of the uncertainties related to investigation of maritime accidents.

scholarly journals Modelling an enterprise global IP network with multimedia services

2019 ◽  
Vol 6 ◽  
pp. 45-53
Author(s):  
Yoana Ivanova
Keyword(s):  
Simulation Model ◽  
Simulation Software ◽  
Multimedia Content ◽  
Multimedia Services ◽  
High Quality ◽  
Operational Costs ◽  
Ip Network ◽  
Packet Tracer ◽  
Quality Of Voice

The aim of this paper is building a simulation model of an enterprise global IP network with multimedia services using the network simulation software Cisco Packet Tracer. They are examined protocols for the realization of the VoIP service and providing multimedia content to end users with guaranteed high quality of voice and multimedia services. The result of the research is a simulation model implemented using Cisco networking devices that are selected due to their advantages compared to other device models. The applied contributions are expressed in reducing the operational costs and ensuring reliable protection and stability when the load of the network is maximum.

Influence of technology parameters of free-cutting steel continuous casting on the billet internal structure

2020 ◽  
Vol 76 (2) ◽  
pp. 139-142
Author(s):  
A. T. Kunakbaeva ◽  
A. M. Stolyarov ◽  
M. V. Potapova
Keyword(s):  
Regression Analysis ◽  
Continuous Casting ◽  
Internal Structure ◽  
Sulfur Content ◽  
Manganese Content ◽  
High Quality ◽  
Correlation And Regression Analysis ◽  
Cutting Steel ◽  
Continuously Cast

Free-cutting steel gains specific working properties thanks to the high content of sulfur and phosphorus. These elements, especially sulfur, have a rather high tendency to segregation. Therefore, segregation defects in free-cutting steel continuously cast billets can be significantly developed. The aim of the work was to study the influence of the chemical composition of freecutting steel and casting technological parameters on the quality of the macrostructure of continuously cast billets. A metallographic assessment of the internal structure of cast metal made of free-cutting steel and data processing by application of correlation and regression analysis were the research methods. The array of production data of 43 heats of free-cutting steel of grade A12 was studied. Steel casting on a five-strand radial type continuous casting machine was carried out by various methods of metal pouring from tundish into the molds. Metal of 19 heats was poured with an open stream, and 24 heats – by a closed stream through submerged nozzles with a vertical hole. High-quality billets had a cross-sectional size of 150×150 mm. The macrostructure of high-quality square billets made of free-cutting steel of A12 grade is characterized by the presence of central porosity, axial segregation and peripheral point contamination, the degree of development of which was in the range from 1.5 to 2.0 points, segregation cracks and strips – about 1.0 points. In the course of casting with an open stream, almost all of these defects are more developed comparing with the casting by a closed stream. As a result of correlation and regression analysis, linear dependences of the development degree of segregation cracks and strips both axial and angular on the sulfur content in steel and on the ratio of manganese content to sulfur content were established. The degree of these defects development increases with growing of sulfur content in steel of A12 grade. These defects had especially strong development when sulfur content in steel was of more than 0.10%. To improve the quality of cast metal, it is necessary to have the ratio of the manganese content to the sulfur content in the metal more than eight.

Experience of clinical testing of personal telemedicine system ‘Obereg’ for remote monitoring of patients in intensive care units

2020 ◽  
pp. 52-58 ◽  
Author(s):  
A. A. Eryomenko ◽  
N. V. Rostunova ◽  
S. A. Budagyan ◽  
V. V. Stets
Keyword(s):  
Intensive Care ◽  
Intensive Care Units ◽  
Remote Monitoring ◽  
Clinical Testing ◽  
Transportation Of Patients ◽  
High Quality ◽  
Telemedicine System ◽  
Accuracy Of Measurements ◽  
Hospital Equipment

The experience of clinical testing of the personal telemedicine system ‘Obereg’ for remote monitoring of patients at the intensive care units of leading Russian clinics is described. The high quality of communication with the remote receiving devices of doctors, the accuracy of measurements, resistance to interference from various hospital equipment and the absence of its own impact on such equipment were confirmed. There are significant advantages compared to stationary patient monitors, in particular, for intra and out-of-hospital transportation of patients.

METHODOLOGICAL ASPECTS OF VISUALIZATION OF CORONARY ARTERIES WITH TRANSTHORACIC ECHOCARDIOGRAPHY

2018 ◽  
pp. 26-35
Author(s):  
Z. A. Agaeva ◽  
K. B. Baghdasaryan
Keyword(s):  
Blood Flow ◽  
Coronary Blood Flow ◽  
Coronary Arteries ◽  
Transthoracic Echocardiography ◽  
Second Harmonic ◽  
Anatomic Reconstruction ◽  
High Quality ◽  
Acoustic Window ◽  
Methodological Aspects

The transthoracic echocardiography made by multifrequency probes with support of the mode of the second harmonic imaging, is a competitive method for visualization of the main coronary arteries and allows to estimate coronary blood flow with high quality. Of course, the method has considerable restrictions, most important of which is the low spatial resolution of a method, due to small acoustic window. Because of this the transthoracic visualization of coronary arteries perhaps will not become the leading method of anatomic reconstruction of separately taken coronary artery and especially all coronary arteries system. However uniqueness and indisputable advantage of this method is an opportunity to noninvasively estimate a coronary blood flow both once, and in dynamics.

Estimates on poverty in Russia and the additional measures to reduce it at the regional level

2020 ◽  
Vol 18 (4) ◽  
pp. 739-752 ◽  
Author(s):  
R.M. Sadykov
Keyword(s):  
Poverty Rate ◽  
Regional Level ◽  
Living Standards ◽  
Standard Of Living ◽  
High Quality ◽  
Social Standard ◽  
Republic Of Bashkortostan ◽  
The Republic ◽  
Sociological Studies

Subject. This article deals with the issues of social justice and a high quality of life, creating favorable economic and social conditions. Objectives. The article aims to assess the rate and changes in poverty in Russia and the Republic of Bashkortostan and develop complementary measures to reduce it. Methods. For the study, I used the methods of logical, comparative, economic and statistical analyses, the results of sociological studies, and official statistics. Results. The article highlights additional measures to reduce poverty in the region, including the establishment of a minimum social standard of living in each particular region that determines the poverty rate. Conclusions. Various factors, such as economic sanctions, economic slowdowns, territorial and regional imbalances, lead to living standards decline and poverty rise.

SCIENTIFIC BASIS OF POSTGRADUATE TRAINING FOR OFFICER WORKING ETHNIC AFFAIRS USING STATE BUDGET IN THE PERIOD OF 2018 – 2025

2017 ◽  
Author(s):  
La Duc Minh ◽  
Nguyen Thi Hao ◽  
Vu Thi Thuy
Keyword(s):  
Economic Development ◽  
Ethnic Groups ◽  
Human Resource ◽  
Postgraduate Training ◽  
Scientific Basis ◽  
National Defense ◽  
High Quality ◽  
State Budget ◽  
International Integration

Ethnic affairs play an important role in socio of ethnic groups’ solidarity, assurance of security and national defense stability. In -economic development, maintenanceorder to improve the quality of ethnic affairs, it is practical to carry out postgraduate training of officer implementing ethnic affairs using state budget with the aim of encouraging and enhancing officer quality to satisfy high-quality human resource in international integration.

Удобрение перца сладкого

2018 ◽  
Author(s):  
V.A. Borisov ◽  
A.M. Menshikh ◽  
V.S. Sosnov ◽  
G.F. Monakhos
Keyword(s):  
Drip Irrigation ◽  
Sweet Pepper ◽  
Water Soluble ◽  
Mineral Fertilizers ◽  
High Quality ◽  
Organic Mineral ◽  
Soluble Fertilizer

Показано действие минеральных удобрений, микрокристаллического комплексного водорастворимого удобрения «Мастер» и органоминерального наноудобрения с ростостимулирующей активностью «Арксойл» при капельном орошении на урожайность и качество сладкого перца нового гибрида F1 Темп. Сочетание основного удобрения с листовой и корневой подкормками позволяет получить до 65 т/га плодов перца высокого качества.The action of mineral fertilizers, microcrystalline complex water soluble fertilizer Master and organic mineral nano-fertilizer with growth-stimulating activity Arksoil under drip irrigation on the productivity and quality of sweet pepper of the new hybrid F1 Temp is shown. The combination of basic fertilizer with leaf and root fertilizing allows to obtain up to 65 t/ha of pepper fruits of high quality.

Child Diagnosis of Autism - How It Can Change the Family Life

2017 ◽  
Vol 5 (1) ◽  
pp. 498
Author(s):  
Maria Stănescu
Keyword(s):  
Early Intervention ◽  
Family Life ◽  
Social Life ◽  
Decisive Role ◽  
Autistic Children ◽  
Child Behaviors ◽  
High Quality ◽  
Child Diagnosis ◽  
The Family

The article is about the role of the family in the education and formation of children and, especially, in the life and development of autistic children. It describes the problems their family is facing and the need for counseling to parents with autistic children. The reaction to finding the diagnosis of autism varies from one family to another and may encounter a large variety: from disbelief, anger, guilt, helplessness, devastation, surprise, or even rejection of the child, to understanding and relief when finally the parents have an explanation for their child behaviors. Early intervention is important in psychological sustaining of the parent, as parent involvement in the recovery of the child with autism has a determinant role in his development and in ensuring a high quality of life of the child and the life of the hole family. The response to a child's autism diagnosis varies from one family to another. The family goes through a variety of disbelief, anger, guilt, helplessness, devastation, surprise, or even rejection of the child, to understanding and relief. Early intervention is very important in the psychological support of the parent. Because any change disturbs the family equilibrium. A diagnosis of autism changes not only the life of the diagnosed child, but also the life of family members. All the resources are focused on the need of the child. Although each parent is different, after diagnosing the child with autism, all parents are overwhelmed by confusion, shock and denial. Parents' feelings can be influenced by how their children's situation affects different aspects of life - it has an impact on service, on social life and all their personal life. If we look at the family as a system and when a disturbing factor appears, all parts of the system are affected. The involvement of parents in the recovery of the child with autism has a decisive role in its development and in ensuring a high quality of child's life and family life.

Sign in / Sign up

Export Citation Format

Share Document