Three-dimensional numerical simulation of velocity field distribution in an oxy-coal combustor-melter-separator furnace

2021 ◽  
Vol 118 (5) ◽  
pp. 510
Author(s):  
Yao-zong Shen ◽  
Kai Zhao ◽  
Zheng Kong ◽  
Yu-zhu Zhang ◽  
Yan Shi ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Velocity Field ◽  
Velocity Distribution ◽  
Molten Pool ◽  
Dead Zone ◽  
Sudden Change ◽  
Three Dimensional ◽  
Maximum Velocity ◽  
Simulation Method ◽  
Distribution Area

In view of the influence of tuyere layout change on velocity field in oxy-coal combustor-melter-separator furnace, three-dimensional numerical simulation method was used to compare the distribution of velocity field in the furnace under different tuyere layout. The purpose is to explore the influence of the velocity distribution on the molten pool flow in the process of multi-tuyere injection. It is shown that the maximum velocity of the upper and lower tuyeres is 60 m/s and 50 m/s. And the change of tuyere has a significant effect on the velocity distribution in the molten pool, and the sudden change of velocity near the tuyere will trigger a certain scale of gyratory zone. In addition, the change of tuyere arrangement will result in the concentration of velocity distribution in the molten pool and the increase of flow dead zone, while the change of tuyere spacing will not only promote the increase of flow dead zone, but also reduce the velocity distribution area.

scholarly journals Strata behavior and control strategy of backfilling collaborate with caving fully-mechanized mining

2020 ◽  
Vol 12 (1) ◽  
pp. 703-717
Author(s):  
Yin Wei ◽  
Wang Jiaqi ◽  
Bai Xiaomin ◽  
Sun Wenjie ◽  
Zhou Zheyuan
Keyword(s):  
Numerical Simulation ◽  
Control Strategy ◽  
Three Dimensional ◽  
Simulation Method ◽  
Mine Pressure ◽  
Hydraulic Support ◽  
Transition Area ◽  
Pressure Concentration ◽  
Strata Behavior ◽  
And Control

AbstractThis article analyzes the technical difficulties in full-section backfill mining and briefly introduces the technical principle and advantages of backfilling combined with caving fully mechanized mining (BCCFM). To reveal the strata behavior law of the BCCFM workface, this work establishes a three-dimensional numerical model and designs a simulation method by dynamically updating the modulus parameter of the filling body. By the analysis of numerical simulation, the following conclusions about strata behavior of the BCCFM workface were drawn. (1) The strata behavior of the BCCFM workface shows significant nonsymmetrical characteristics, and the pressure in the caving section is higher than that in the backfilling section. φ has the greatest influence on the backfilling section and the least influence on the caving section. C has a significant influence on the range of abutment pressure in the backfilling section. (2) There exits the transition area with strong mine pressure of the BCCFM workface. φ and C have significant effect on the degree of pressure concentration but little effect on the influence range of strong mine pressure in the transition area. (3) Under different conditions, the influence range of strong mine pressure is all less than 6 m. This article puts forward a control strategy of mine pressure in the transition area, which is appropriately improving the strength of the transition hydraulic support within the influence range (6 m) in the transition area according to the pressure concentration coefficient. The field measurement value of Ji15-31010 workface was consistent with numerical simulation, which verifies the reliability of control strategy of the BCCFM workface.

scholarly journals Study of the Effect of Centrifugal Force on Rotor Blade Icing Process

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Zhengzhi Wang ◽  
Chunling Zhu
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Force ◽  
Rotor Blade ◽  
Flow Direction ◽  
Three Dimensional ◽  
Simulation Method ◽  
Two Phase ◽  
Numerical Simulation Method ◽  
Calculation Results ◽  
Flow Field Characteristics

In view of the rotor icing problems, the influence of centrifugal force on rotor blade icing is investigated. A numerical simulation method of three-dimensional rotor blade icing is presented. Body-fitted grids around the rotor blade are generated using overlapping grid technology and rotor flow field characteristics are obtained by solving N-S equations. According to Eulerian two-phase flow, the droplet trajectories are calculated and droplet impingement characteristics are obtained. The mass and energy conservation equations of ice accretion model are established and a new calculation method of runback water mass based on shear stress and centrifugal force is proposed to simulate water flow and ice shape. The calculation results are compared with available experimental results in order to verify the correctness of the numerical simulation method. The influence of centrifugal force on rotor icing is calculated. The results show that the flow direction and distribution of liquid water on rotor surfaces change under the action of centrifugal force, which lead to the increasing of icing at the stagnation point and the decreasing of icing on both frozen limitations.

Calculation and Design Method Study of the Coil-Wound Heat Exchanger

2014 ◽  
Vol 1008-1009 ◽  
pp. 850-860 ◽  
Author(s):  
Zhou Wei Zhang ◽  
Jia Xing Xue ◽  
Ya Hong Wang
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Heat Exchanger ◽  
Design Method ◽  
Fluid Velocity ◽  
Exchange Process ◽  
Three Dimensional ◽  
Simulation Method ◽  
Physical Parameters ◽  
Numerical Result

A calculation method for counter-current type coil-wound heat exchanger is presented for heat exchange process. The numerical simulation method is applied to determine the basic physical parameters of wound bundles. By controlling the inlet fluid velocity varying in coil-wound heat exchanger to program and calculate the iterative process. The calculation data is analyzed by comparison of numerical result and the unit three dimensional pipe bundle model was built. Studies show that the introduction of numerical simulation can simplify the pipe winding process and accelerate the calculation and design of overall configuration in coil-wound heat exchanger. This method can be applied to the physical modeling and heat transfer calculation of pipe bundles in coil wound heat exchanger, program to calculate the complex heat transfer changing with velocity and other parameters, and optimize the overall design and calculation of spiral bundles.

The Research on Steering Fracture Numerical Simulation

2013 ◽  
Vol 734-737 ◽  
pp. 1488-1492
Author(s):  
Zhen Yu Liu ◽  
Li Hong Yao ◽  
Hu Zhen Wang ◽  
Cui Cui Ye
Keyword(s):  
Numerical Simulation ◽  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
Simulation Method ◽  
Production Performance ◽  
Phase Flow ◽  
Water Production ◽  
Two Phase ◽  
Fractured Well

The fractures after artificial steering fracturing appear in shades of curved surface. Aiming at the problem of steering fracture, in the paper, numerical simulation method under the condition of three-dimensional two-phase flow is presented based on finite element method. In this method, of steering fracture was achieved by adopting surface elements fractures and tetrahedron elements to describe formation. By numerical simulation, the change rule of oil and water production performance of steering fractures can be calculated, and then the steering fracture parameters can be optimized before fracturing. A new method was supplied for the numerical simulation of artificial fractured well.

Investigation of the Submerged Depth of Aeration Impellers in an Oxidation Ditch by Numerical Simulation

2012 ◽  
Vol 178-181 ◽  
pp. 429-432
Author(s):  
Y. L. Liu ◽  
B. Lv ◽  
W.L. Wei
Keyword(s):  
Numerical Simulation ◽  
Velocity Distribution ◽  
Average Velocity ◽  
Sewage Treatment ◽  
Processing System ◽  
Simulation Method ◽  
Velocity Fields ◽  
Oxidation Ditch ◽  
Depth Direction ◽  
Sewage Treatment System

In this paper, the flow structure of the oxidation ditch was studied using numerical simulation method and different submerged depth of aeration impellers. The computed velocity fields were analyzed, which shows that under the same conditions, and by using the optimal submerged depth the average velocity of the flow in oxidation ditch is increased and the velocity near-bottom has increased significantly. The results of comparisons show that the velocity distribution is more uniform along the depth direction, and that the flow velocity distribution structure can prevent sludge from settling in the oxidation ditch processing system at the submergence ratio called the optimal submergence ratio, which helps to improve the efficiency of oxidation ditch sewage treatment system.

scholarly journals Study on Fluorine Pollution in a Slag Yard

2019 ◽  
Vol 9 (5) ◽  
pp. 847
Author(s):  
Lide Wei ◽  
Changfu Wei ◽  
Sugang Sui
Keyword(s):  
Numerical Simulation ◽  
Experimental Investigation ◽  
Numerical Simulations ◽  
Solute Transport ◽  
Large Scale ◽  
Three Dimensional ◽  
Simulation Method ◽  
Laboratory Studies ◽  
Survey Results ◽  
Simulation Results

This paper suggests a large-scale three-dimensional numerical simulation method to investigate the fluorine pollution near a slag yard. The large-scale three-dimensional numerical simulation method included an experimental investigation, laboratory studies of solute transport during absorption of water by soil, and large-scale three-dimensional numerical simulations of solute transport. The experimental results showed that the concentrations of fluorine from smelting slag and construction waste soil were well over the discharge limit of 0.1 kg/m3 recommended by Chinese guidelines. The key parameters of the materials used for large-scale three-dimensional numerical simulations were determined based on an experimental investigation, laboratory studies, and soil saturation of survey results and back analyses. A large-scale three-dimensional numerical simulation of solute transport was performed, and its results were compared to the experiment results. The simulation results showed that the clay near the slag had a high saturation of approximately 0.9, consistent with the survey results. Comparison of the results showed that the results of the numerical simulation of solute transport and the test results were nearly identical, and that the numerical simulation results could be used as the basis for groundwater environmental evaluation.

Transient Simulation of a Three-Dimensional Moving Downburst

2012 ◽  
Vol 446-449 ◽  
pp. 3875-3878
Author(s):  
Bai Feng Ji ◽  
Wei Lian Qu
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Computational Fluid Dynamics ◽  
Wind Field ◽  
Three Dimensional ◽  
Simulation Method ◽  
Transient Simulation ◽  
Dynamics Simulation ◽  
Transmission Tower ◽  
Transient Wind

Thunderstorm microbursts, which are sources of extreme wind loadings in nature, have caused numerous structural failures, especially collapses of transmission tower around the world. Numerical simulation using computational fluid dynamics (CFD) has recently made significant progress in simulating downbursts. In this paper, transient simulation of a three-dimensional moving downburst was studied using computational fluid dynamics simulation method. Transient simulation of a three-dimensional moving downburst was conducted using time-filtered Reynolds Averaged Navier-Stokes (RANS) numerical simulation method. The three-dimensional transient wind field characteristics in a moving downburst were studied in detail. The results indicate that transient wind field characteristics in a moving downburst present quite different characteristics compared with stationary downburst at different heights and radial positions.

Three-Dimensional Numerical Simulation of the Flow around Two Side-by-Side Cylinders of Different Diameters

2014 ◽  
Vol 721 ◽  
pp. 199-202
Author(s):  
Zhen Xiao Bi ◽  
Zhi Han Zhu
Keyword(s):  
Numerical Simulation ◽  
Flow Direction ◽  
Three Dimensional ◽  
Cross Flow ◽  
Simulation Method ◽  
Scale Model ◽  
Hydrodynamic Characteristics ◽  
Eddy Simulation ◽  
Drag And Lift ◽  
Different Diameters

This paper presents the calculation of hydrodynamic characteristics of two side-by-side cylinders of different diameters in three dimensional incompressible uniform cross flow by using Large-eddy simulation method based on dynamical Smagorinsky-Lilly sub-grid scale model. Solution of the three dimensional N-S equations were obtained by the finite volume method. The numerical simulation focused on investigating the characteristic of the pressure distribution (drag and lift force), vorticity field and turbulence Re=. Results shows that, the asymmetry of the time –averaged velocity distribution in the flow direction behind the two cylinders is very obvious; the frequency of eddy shedding of the small cylinder is about twice of the large one. The turbulence of cylinders is more obvious.

Sign in / Sign up

Export Citation Format

Share Document