Influence of sintering temperature and pH on the phase transformation, particle size and anti-reflective properties of RHA nano silica powders

2012 ◽  
Vol 85 (12) ◽  
pp. 1109-1124 ◽  
Author(s):  
K. Saravanan ◽  
R. Yuvakkumar ◽  
V. Rajendran ◽  
P. Paramasivam
Keyword(s):  
Particle Size ◽  
Phase Transformation ◽  
Sintering Temperature ◽  
Nano Silica

scholarly journals The effect of milling time on the alumina phase transformation in the AMCs powder metallurgy reinforced by silica-sand-tailings

2022 ◽  
pp. 103-117
Author(s):  
Sukanto ◽  
Wahyono Suprapto ◽  
Rudy Soenoko ◽  
Yudy Surya Irawan
Keyword(s):  
Particle Size ◽  
Phase Transformation ◽  
Powder Metallurgy ◽  
Mechanical Alloying ◽  
Milling Time ◽  
Sintering Temperature ◽  
Silica Sand ◽  
Second Phase ◽  
The Matrix ◽  
The Impact

This study aims to determine the effect of milling time and sintering temperature parameters on the alumina transformation phase in the manufacture of Aluminium Matrix Composites (AMCs) reinforced by 20 % silica sand tailings using powder metallurgy technology. The matrix and fillers use waste to make the composites more efficient, clean the environment, and increase waste utilization. The milling time applied to the Mechanical Alloying (MA) process was 0.5, 6, 24, 48, and 96 hours, with a ball parameter ratio of 15:1 and a rotation of 93 rpm. Furthermore, hot compaction was carried out using a 100 MPa two-way hydraulic compression machine at a temperature of 300 °C for 20 minutes. The temperature variables of the sintering parameter process were 550, 600 to 650 °C, with a holding time of 10 minutes. Characterization of materials carried out included testing particle size, porosity, X-Ray Diffraction (XRD), SEM-Image, and SEM-EDX. The particle measurement of mechanical alloying processed, using Particle Size Analyzer (PSA) instrument and based on XRD data using the Scherrer equation, showed a relatively similar trend, decreasing particle size occurs when milling time was increased 0.5 to 24 hours. However, when the milling time increases to 48 and 96 hours, the particle size tends to increase slightly, due to cold-weld and agglomeration when the Mechanical Alloying is processed. The impact is the occurrence of the matrix and filler particle pairs in the cold-weld state. So, the results of XRD and SEM-EDX characterization showed a second phase transformation to form alumina compounds at a relatively low sintering temperature of 600 °C after the mechanical alloying process was carried out with a milling time on least 24 hours

Phase transformation and Raman spectra in BaTiO3 nanocrystals

2002 ◽  
Vol 718 ◽  
Author(s):  
Jian Yu ◽  
X. J. Meng ◽  
J.L. Sun ◽  
G.S. Wang ◽  
J.H. Chu
Keyword(s):  
Particle Size ◽  
Phase Transformation ◽  
Low Temperature ◽  
Long Range ◽  
Lattice Expansion ◽  
Inversion Symmetry ◽  
Range Interaction ◽  
Cooperative Phenomena ◽  
Long Range Interaction ◽  
Hydrothermal Methods

AbstractIn this paper, size-induced ferroelectricit yweakening, phase transformation, and anomalous lattice expansion are observed in nanocrystalline BaTiO3 (nc-BaTiO3) deriv ed b y low temperature hydrothermal methods, and they are w ellunderstood using the terms of the long-range interaction and its cooperative phenomena altered by particle size in covalen t ionic nanocrystals. In cubic nc-BaTiO3, five modes centerd at 186, 254, 308, 512 and 716 cm-1 are observed Raman active in cubic nanophase, and they are attributed to local rhombohedral distortion breaking inversion-symmetry in cubic nanophase. The254 and 308 cm-1 modes are significantly affected not only by the concentration of hydroxyl defects, but also their particular configuration. And the 806 cm-1 modes found to be closely associated with OH - absorbed on grain boundaries.

Size-dependent solution-mediated phase transformation of piroxicam monohydrate particles

CrystEngComm ◽  
2021 ◽  
Vol 23 (16) ◽  
pp. 2928-2932
Author(s):  
Changlin Yao ◽  
Lei Wang ◽  
Xinyuan Wang ◽  
Xutang Tao
Keyword(s):  
Particle Size ◽  
Phase Transformation ◽  
Size Dependent

The transformation from the piroxicam monohydrate to form I or form II could be achieved precisely by adjusting the particle size itself in the 99% acetone-1% H2O solvent at 31 °C.

EFFECTS OF PARTICLE SIZE AND SINTERING TEMPERATURE ON SUPERELASTICITY BEHAVIOR OF NiTi SHAPE MEMORY ALLOY USING NANOINDENTATION

2021 ◽  
pp. 2150024
Author(s):  
C. VELMURUGAN ◽  
V. SENTHILKUMAR
Keyword(s):  
Particle Size ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Sintering Temperature ◽  
Niti Alloy ◽  
Indentation Load ◽  
Niti Shape Memory Alloy ◽  
Recovery Ratio ◽  
Work Recovery ◽  
Niti Sma

The present study investigates the superelasticity properties of spark plasma sintered (SPS) nickel titanium shape memory alloy (NiTi SMA) with the influence of sintering temperature and particle size. The nanoindentation is conducted on the surface of the NiTi SMA at various loads such as 100, 300 and 500[Formula: see text]mN. The nanoindentation technique determines the quantitative results of elasto-plastic properties such as depth recovery in the form of superelasticity, stiffness, hardness and work recovery ratio from load–depth ([Formula: see text]–[Formula: see text]) data during loading and unloading of the indenter. Experimental findings show that the depth and work recovery ratio increases with the decrease of indentation load and particle size. In contrast, increasing the sintering temperature exhibited a better depth and work recovery due to the removal of pores which could enhance the reverse transformation. The contact stiffness is influenced by [Formula: see text] which leads to attain a maximum stiffness at the highest load (500[Formula: see text]mN) and particle size (45[Formula: see text][Formula: see text]m) along with the lowest sintering temperature (700∘C). NiTi alloy exhibited a maximum hardness of 9.46[Formula: see text]GPa when subjected to indent at the lowest load and particle size sintered at 800∘C. The present study reveals a better superelastic behavior in NiTi SMA by reducing the particle size and indentation load associated with the enhancement of sintering temperature.

Aluminate Green Phosphor with Small Particle Size Used for PDP via Co-Precipitation Method

2011 ◽  
Vol 295-297 ◽  
pp. 890-895
Author(s):  
Yan Dong ◽  
Yang Zhou ◽  
Xue Lin Han ◽  
Wei Jie Gu
Keyword(s):  
Particle Size ◽  
Phase Transformation ◽  
Small Particle ◽  
High Efficiency ◽  
Particle Growth ◽  
Solid State Reaction Method ◽  
Precipitation Method ◽  
Small Particle Size ◽  
Green Phosphor ◽  
Co Precipitation

Mg doped BaAl12O19:Mn2+ phosphor is one of the most efficient green phosphors for PDP. It is difficult to prepare the phosphor both have small particle size (< 3μm) and high luminescence. In the present work, a BaAl12O19:Mn2+ phosphor with small particle size was synthesized by the chemical co-precipitation method. Phase transformation and particle growth process during calcining process were investigated. The nucleation process was also discussed. The results show that, the phase transformation is complicated, the transition phases include BaCO3, γ-Al2O3, BaF2, BaAl2O4 and two phases contain Mn; The BaAl12O19 phase is formed from the reaction between BaAl2O4 phase and γ-Al2O3 phase, no a-Al2O3 phase appears during the entire process; The formation temperature of pure BaAl12O19 phase is 1200°C, which is lower than that in the high-temperature solid state reaction method. High efficiency BaAl12O19:Mn2+ phosphor with small particle size (< 2μm) and hexagonal flaky shape can be prepared by this method.

Effect of Process on the Dielectric Properties of BaTiO3-Based X9R Ceramics

2014 ◽  
Vol 906 ◽  
pp. 18-24 ◽  
Author(s):  
Bao Lin Zhang ◽  
Bin Bin Zhang ◽  
Ning Ning Wang ◽  
Jing Ming Fei
Keyword(s):  
Particle Size ◽  
Dielectric Properties ◽  
Milling Time ◽  
Sintering Temperature ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Sintered Ceramic ◽  
X Ray ◽  
Particle Size Analyzer

The effect of milling time and sintering process on the dielectric properties of BaTiO3-based X9R ceramics was investigated. The characterization of the raw powders and the sintered ceramic was carried out by X-ray diffraction and scanning electron microscopy. The particle size distribution of the mixed powders was examined by Laser Particle Size Analyzer. The results shown that with the milling time extended, the Cruie Peak was depressed, or even disappeared. Moreover, with the rise of sintering temperature, the dielectric constant of the ceramics increased and the dielectric loss decreased gradually. Eventually, by milling for 11h and sintering at 1090°Cfor 2h, good dielectric properties were obtained, which were ε25°C≥ 2526, εr/εr25°C≤± 12% (–55~200°C), tanδ≤1.12% (25°C).

scholarly journals Exploring the relationship between solvent-assisted ball milling, particle size, and sintering temperature in garnet-type solid electrolytes

2021 ◽  
Vol 484 ◽  
pp. 229252
Author(s):  
Marissa Wood ◽  
Xiaosi Gao ◽  
Rongpei Shi ◽  
Tae Wook Heo ◽  
Jose Ali Espitia ◽  
...  
Keyword(s):  
Particle Size ◽  
Ball Milling ◽  
Solid Electrolytes ◽  
Sintering Temperature ◽  
The Relationship

Effects of Micropores on Processing and Properties of Porous Irons

2017 ◽  
Vol 863 ◽  
pp. 26-32
Author(s):  
Ming Zhou Su ◽  
Hui Meng Wang ◽  
Chang Chen
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Corn Starch ◽  
Sintering Temperature ◽  
Starch Content ◽  
Volumetric Shrinkage ◽  
Small Particle Size ◽  
Compressive Properties ◽  
Different Temperatures ◽  
Powder Metallurgy Route

Porous irons with only micropores were produced through powder metallurgy route. Corn starch of small particle size (5-15μm) was utilized to regulate the densification of green compacts. The structural and mechanical properties of porous irons sintered at different temperatures were evaluated. The porosities increased with increasing the starch content, which reduced compressive strength and increased volumetric shrinkage. The compressive yield stress increased with increasing sintering temperature. It was also found that the effect of sintering temperature on the microstructure and compressive properties was more obvious when green compacts were less densified. Moreover, volumetric shrinkage of porous irons without adding starch remains in a quite low level for different sintering temperatures.

Sign in / Sign up

Export Citation Format

Share Document