scholarly journals Numerical study on aerodynamic characteristics of rotating missile launched vertically under strong transverse wind

2020 ◽  
Vol 1507 ◽  
pp. 082013
Author(s):  
Yihang Xu ◽  
Shaosong Chen ◽  
Hang Zhou
Keyword(s):  
Numerical Study ◽  
Aerodynamic Characteristics ◽  
Strong Transverse

Numerical study of geometric morphing wings of the 1303 UCAV

2021 ◽  
pp. 1-17
Author(s):  
B. Nugroho ◽  
J. Brett ◽  
B.T. Bleckly ◽  
R.C. Chin
Keyword(s):  
Flight Control ◽  
Numerical Study ◽  
Aerodynamic Characteristics ◽  
Morphing Wing ◽  
Rolling Moment ◽  
Wide Range ◽  
Morphing Wings ◽  
Wing Geometry ◽  
Lift And Drag ◽  
Wing Morphing

ABSTRACT Unmanned Combat Aerial Vehicles (UCAVs) are believed by many to be the future of aerial strike/reconnaissance capability. This belief led to the design of the UCAV 1303 by Boeing Phantom Works and the US Airforce Lab in the late 1990s. Because UCAV 1303 is expected to take on a wide range of mission roles that are risky for human pilots, it needs to be highly adaptable. Geometric morphing can provide such adaptability and allow the UCAV 1303 to optimise its physical feature mid-flight to increase the lift-to-drag ratio, manoeuvrability, cruise distance, flight control, etc. This capability is extremely beneficial since it will enable the UCAV to reconcile conflicting mission requirements (e.g. loiter and dash within the same mission). In this study, we conduct several modifications to the wing geometry of UCAV 1303 via Computational Fluid Dynamics (CFD) to analyse its aerodynamic characteristics produced by a range of different wing geometric morphs. Here we look into two specific geometric morphing wings: linear twists on one of the wings and linear twists at both wings (wash-in and washout). A baseline CFD of the UCAV 1303 without any wing morphing is validated against published wind tunnel data, before proceeding to simulate morphing wing configurations. The results show that geometric morphing wing influences the UCAV-1303 aerodynamic characteristics significantly, improving the coefficient of lift and drag, pitching moment and rolling moment.

Effect of Vaned Diffuser on a Modified Turbocharger Centrifugal Compressor Performance

2014 ◽  
Vol 663 ◽  
pp. 347-353
Author(s):  
Layth H. Jawad ◽  
Shahrir Abdullah ◽  
Zulkifli R. ◽  
Wan Mohd Faizal Wan Mahmood
Keyword(s):  
Centrifugal Compressor ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Width Ratio ◽  
Outlet Section ◽  
Suction Surface ◽  
Vaned Diffuser ◽  
Minimum Width

A numerical study that was made in a three-dimensional flow, carried out in a modified centrifugal compressor, having vaned diffuser stage, used as an automotive turbo charger. In order to study the influence of vaned diffuser meridional outlet section with a different width ratio of the modified centrifugal compressor. Moreover, the performance of the centrifugal compressor was dependent on the proper matching between the compressor impeller along the vaned diffuser. The aerodynamic characteristics were compared under different meridional width ratio. In addition, the velocity vectors in diffuser flow passages, and the secondary flow in cross-section near the outlet of diffuser were analysed in detail under different meridional width ratio. Another aim of this research was to study and simulate the effect of vaned diffuser on the performance of a centrifugal compressor. The simulation was undertaken using commercial software so-called ANSYS CFX, to predict numerically the performance charachteristics. The results were generated from CFD and were analysed for better understanding of the fluid flow through centrifugal compressor stage and as a result of the minimum width ratio the flow in diffuser passage tends to be uniformity. Moreover, the backflow and vortex near the pressure surface disappear, and the vortex and detachment near the suction surface decrease. Conclusively, it was observed that the efficiency was increased and both the total pressure ratio and static pressure for minimum width ratio are increased.

Numerical study of the aerodynamic and power characteristics of the cycloidal rotor, under incoming flow

2019 ◽  
pp. 25-34
Author(s):  
Александр Анатольевич Дектерев ◽  
Артем Александрович Дектерев ◽  
Юрий Николаевич Горюнов
Keyword(s):  
Flow Velocity ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Simulation Method ◽  
Aerodynamic Characteristics ◽  
Incoming Flow ◽  
Ansys Fluent ◽  
Energy Characteristics ◽  
Power Characteristics ◽  
Calculation Results

Исследование направлено на разработку и апробацию методики численного моделирования аэродинамических и энергетических характеристик циклоидального ротора. За основу взята конфигурация ротора IAT21 L3. Для нее с использованием CFD-пакета ANSYS Fluent построена математическая модель и выполнен расчет. Проанализировано влияние скорости набегающего потока воздуха на движущийся ротор. Математическая модель и полученные результаты исследования могут быть использованы при создании летательных аппаратов с движителями роторного типа. This article addresses the study of the aerodynamic and energy characteristics of a cycloidal rotor subject to the influence of the incoming flow. Cycloidal rotor is one of the perspective devices that provide movement of aircrafts. Despite the fact that the concept of a cycloidal rotor arose in the early twentieth century, the model of a full-scale aircraft has not been yet realized. Foreign scientists have developed models of aircraft ranging in weight from 0.06 to 100 kg. The method of numerical calculation of the cycloidal rotor from the article [1] is considered and realized in this study. The purpose of study was the development and testing of a numerical simulation method for the cycloidal rotor and study aerodynamic and energy characteristics of the rotor in the hovering mode and under the influence of the oncoming flow. The aerodynamic and energy characteristics of the cycloidal rotor, rotating at a speed of 1000 rpm with incoming flow on it with velocities of 20-80 km/h, were calculated. The calculation results showed a directly proportional increase of thrust with an increase of the incoming on the rotor flow velocity, but the power consumed by the rotor was also increased. Increase of the incoming flow velocity leads to the proportional increasing of the lift coefficient and the coefficient of drag. Up to a speed of 80 km/h, an increase in thrust and power is observed; at higher speeds, there is a predominance of nonstationary effects and difficulties in estimating the aerodynamic characteristics of the rotor. In the future, it is planned to consider the 3D formulation of the problem combined with possibility of the flow coming from other sides.

Aerodynamic optimisation of the rocket plane in subsonic and supersonic flight conditions

2017 ◽  
Vol 231 (12) ◽  
pp. 2266-2281 ◽  
Author(s):  
Marcin Figat ◽  
Agnieszka Kwiek
Keyword(s):  
Mach Number ◽  
Main Part ◽  
Numerical Study ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Design ◽  
Supersonic Speed ◽  
Supersonic Flight ◽  
Special Vehicle ◽  
Speed Regime ◽  
The Impact

This paper presents the results of a numerical study of the aerodynamic shape of the Rocket Plane LEX. The Rocket Plane is a main part of the Modular Airplane System – MAS; a special vehicle devoted to suborbital tourist flights. The Rocket Plane was designed for subsonic and supersonic flight conditions. Therefore, the impact of the Mach number should be considered during the aerodynamic design of the Rocket Plane. The main goal of the investigation was to determine the sensitivity of the Rocket Plane aerodynamic characteristics to the Mach number during the optimisation of the LEX geometry. The paper includes results of the optimisation process for Mach number from the range Ma = 0.5 to Ma = 2.5. These results reveal that the aerodynamic characteristics of models optimised for the subsonic and transonic regime of Mach numbers (up to Ma = 1) were also improved for the supersonic speed regime. However, in the case of models optimised for the supersonic flight regime the aerodynamic characteristics in subsonic flight regime, are inferior compared to the model before the optimisation process.

Experimental and Numerical Study on Aerodynamic Characteristics of a Flapping Wing with Angled Cross-Section

2017 ◽  
Vol 2017 (0) ◽  
pp. J0240201
Author(s):  
Satoshi IKEDA ◽  
Hiroto NAGAI ◽  
Nobuhide UDA ◽  
Yuichi HIRAKAWA ◽  
Masahiko MUROZONO
Keyword(s):  
Cross Section ◽  
Numerical Study ◽  
Aerodynamic Characteristics ◽  
Flapping Wing

Studies on Aerodynamic Characteristics of Dump Diffusers for Modern Aircraft Engines

2012 ◽  
Vol 232 ◽  
pp. 246-251 ◽  
Author(s):  
P. Sathyan ◽  
S. Srikanth ◽  
I. Dheepan ◽  
M. Arun ◽  
C. Aswin ◽  
...  
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Aerodynamic Characteristics ◽  
Navier Stokes ◽  
Finite Volume Scheme ◽  
Aircraft Engines ◽  
Navier Stokes Equations ◽  
Dynamic Constraints ◽  
Fully Implicit

The geometrical optimization of dump diffusers are extremely demanding as the flow fields and stress fields are very complex and must be well understood to achieve the required design efficiencies. In this paper parametric analytical studies have been carried out for examining the aerodynamics characteristics of different dump diffusers for modern aircraft engines. Numerical studies have been carried out using SST K- ω turbulence model. This code solves SST k- ω turbulence equations using the coupled second order implicit unsteady formulation. In the numerical study, a fully implicit finite volume scheme of the compressible, Reynolds-Averaged, Navier-Stokes equations is employed. We concluded that in addition to the dump gap ratio, the aerodynamic shape of the flame tube case and the other geometric variables are also need to be optimized judiciously after considering the fluid dynamic constraints for controlling the pressure recovery and the losses.

Sign in / Sign up

Export Citation Format

Share Document