scholarly journals Velocity measurements of individual droplets in liquid-liquid Taylor flows in circular capillaries

2021 ◽  
Vol 2116 (1) ◽  
pp. 012074
Author(s):  
Seyyed Saeed Shojaee Zadeh ◽  
Patrick Walsh ◽  
Vanessa Egan
Keyword(s):  
Strong Influence ◽  
Viscosity Ratio ◽  
Flow Regimes ◽  
Bond Number ◽  
Droplet Velocity ◽  
Velocity Measurements ◽  
Wide Range ◽  
Set Up ◽  
Varying Viscosity ◽  
Flow Velocities

Abstract This study is focused on the effect of droplet length on droplet velocity in liquid-liquid Taylor flows for microfluidic applications. An experimental set up was designed to measure droplet velocity over a wide range of droplet lengths and flow velocities while also varying viscosity ratio. Five different fluid combinations were examined by employing AR20, FC40, HFE7500 and water. Results indicate the complexity of predicting droplet velocity in such flow regimes and also show a strong influence of viscosity ratio and Bond number.

On the buoyancy-driven motion of a drop towards a rigid surface or a deformable interface

1990 ◽  
Vol 217 ◽  
pp. 547-573 ◽  
Author(s):  
Stergios G. Yiantsios ◽  
Robert H. Davis
Keyword(s):  
Solid Surface ◽  
Viscosity Ratio ◽  
Bond Number ◽  
Boundary Integral ◽  
Fractional Powers ◽  
Drop Shape ◽  
Wide Range ◽  
Deformable Interface ◽  
Long Time ◽  
Viscous Drop

The deformation of a viscous drop, driven by buoyancy towards a solid surface or a deformable interface, is analysed in the asymptotic limit of small Bond number, for which the deformation becomes important only when the drop is close to the solid surface or interface. Lubrication theory is used to describe the flow in the thin gap between the drop and the solid surface or interface, and boundary-integral theory is used in the fluid phases on either side of the gap. The evolution of the drop shape is traced from a relatively undeformed state until a dimple is formed and a long-time quasi-steady-state pattern is established. A wide range of drop to suspending phase viscosity ratios is examined. It is shown that a dimple is always formed, independently of the viscosity ratio, and that the long-time thinning rates take simple forms as inverse fractional powers of time.

Settlers or Movers? The Temporality of Past Migrations, Political Inaction and its Consequences, 1945–1985

2018 ◽  
Author(s):  
Jozefien De Bock
Keyword(s):  
Temporary Workers ◽  
Guest Workers ◽  
Temporary Migration ◽  
Wide Range ◽  
Settler Societies ◽  
Future Policy ◽  
Set Up ◽  
Legal Frameworks ◽  
Temporary Migrants ◽  
Multicultural Policies

Historically, those societies that have the longest tradition in multicultural policies are settler societies. The question of how to deal with temporary migrants has only recently aroused their interest. In Europe, temporary migration programmes have a much longer history. In the period after WWII, a wide range of legal frameworks were set up to import temporary workers, who came to be known as guest workers. In the end, many of these ‘guests’ settled in Europe permanently. Their presence lay at the basis of European multicultural policies. However, when these policies were drafted, the former mobility of guest workers had been forgotten. This chapter will focus on this mobility of initially temporary workers, comparing the period of economic growth 1945-1974 with the years after the 1974 economic crisis. Further, it will look at the kind of policies that were developed towards guest workers in the era before multiculturalism. This way, it shows how their consideration as temporary residents had far-reaching consequences for the immigrants, their descendants and the receiving societies involved. The chapter will finish by suggesting a number of lessons from the past. If the mobility-gap between guest workers and present-day migrants is not as big as generally assumed, then the consequences of previous neglect should serve as a warning for future policy making.

ORAL HISTORY SOURCES AS LEARNING MATERIALS: A CASE STUDY OF THE NATIONAL UNIVERSITY OF SCIENCE AND TECHNOLOGY

2016 ◽  
Vol 3 (2) ◽  
pp. 82-93
Author(s):  
Gugulethu Shamaine Nkala ◽  
Rodreck David
Keyword(s):  
Oral History ◽  
Learning Experience ◽  
Science And Technology ◽  
Group Discussion ◽  
Human Interaction ◽  
Learning Material ◽  
Wide Range ◽  
National Archives ◽  
National University ◽  
Set Up

Knowledge presented by Oral History (OH) is unique in that it shares the tacit perspective, thoughts, opinions and understanding of the interviewee in its primary form. While teachers, lecturers and other education specialists have at their disposal a wide range of primary, secondary and tertiary sources upon which to relate and share or impart knowledge, OH presents a rich source of information that can improve the learning and knowledge impartation experience. The uniqueness of OH is presented in the following advantages of its use: it allows one to learn about the perspectives of individuals who might not otherwise appear in the historical record; it allows one to compensate for the digital age; one can learn different kinds of information; it provides historical actors with an opportunity to tell their own stories in their own words; and it offers a rich opportunity for human interaction. This article discusses the placement of oral history in the classroom set-up by investigating its use as a source of learning material presented by the National Archives of Zimbabwe to students in the Department of Records and Archives Management at the National University of Science and Technology (NUST). Interviews and a group discussion were used to gather data from an archivist at the National Archives of Zimbabwe, lecturers and students in the Department of Records and Archives Management at NUST, respectively. These groups were approached on the usability, uniqueness and other characteristics that support this type of knowledge about OH in a tertiary learning experience. The findings indicate several qualities that reflect the richness of OH as a teaching source material in a classroom set-up. It further points to weak areas that may be addressed where the source is considered a viable strategy for knowledge sharing and learning. The researchers present a possible model that can be used to champion the use of this rich knowledge source in classroom education at this university and in similar set-ups. 

Nanofiltration of endocrine disrupting compounds

2003 ◽  
Vol 3 (5-6) ◽  
pp. 321-327 ◽  
Author(s):  
M. Gallenkemper ◽  
T. Wintgens ◽  
T. Melin
Keyword(s):  
Wastewater Treatment ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Endocrine Disrupting Compounds ◽  
Municipal Wastewater Treatment ◽  
Water And Wastewater Treatment ◽  
Wide Range ◽  
Endocrine Disrupting ◽  
Municipal Wastewater Treatment Plants ◽  
Set Up

Endocrine disrupting compounds can affect the hormone system in organisms. A wide range of endocrine disrupters were found in sewage and effluents of municipal wastewater treatment plants. Toxicological evaluations indicate that conventional wastewater treatment plants are not able to remove these substances sufficiently before disposing effluent into the environment. Membrane technology, which is proving to be an effective barrier to these substances, is the subject of this research. Nanofiltration provides high quality permeates in water and wastewater treatment. Eleven different nanofiltration membranes were tested in the laboratory set-up. The observed retention for nonylphenol (NP) and bisphenol A (BPA) ranged between 70% and 100%. The contact angle is an indicator for the hydrophobicity of a membrane, whose influence on the permeability and retention of NP was evident. The retention of BPA was found to be inversely proportional to the membrane permeability.

scholarly journals A System-Agnostic, Adaptable and Extensible Animal Support Cradle System for Cardio-Respiratory-Synchronised, and Other, Multi-Modal Imaging of Small Animals

Tomography ◽  
2021 ◽  
Vol 7 (1) ◽  
pp. 39-54
Author(s):  
Veerle Kersemans ◽  
Stuart Gilchrist ◽  
Philip Danny Allen ◽  
Sheena Wallington ◽  
Paul Kinchesh ◽  
...  
Keyword(s):  
Scientific Data ◽  
Cardiac Monitoring ◽  
Small Animals ◽  
Maintenance System ◽  
Wide Range ◽  
Set Up ◽  
Animal Handling ◽  
Imaging Performance ◽  
Significant Effort

Standardisation of animal handling procedures for a wide range of preclinical imaging scanners will improve imaging performance and reproducibility of scientific data. Whilst there has been significant effort in defining how well scanners should operate and how in vivo experimentation should be practised, there is little detail on how to achieve optimal scanner performance with best practices in animal welfare. Here, we describe a system-agnostic, adaptable and extensible animal support cradle system for cardio-respiratory-synchronised, and other, multi-modal imaging of small animals. The animal support cradle can be adapted on a per application basis and features integrated tubing for anaesthetic and tracer delivery, an electrically driven rectal temperature maintenance system and respiratory and cardiac monitoring. Through a combination of careful material and device selection, we have described an approach that allows animals to be transferred whilst under general anaesthesia between any of the tomographic scanners we currently or have previously operated. The set-up is minimally invasive, cheap and easy to implement and for multi-modal, multi-vendor imaging of small animals.

scholarly journals LED Rail Signals: Full Hardware Realization of Apparatus with Independent Intensity by Temperature Changes

Electronics ◽  
2021 ◽  
Vol 10 (11) ◽  
pp. 1291
Author(s):  
Giuseppe Schirripa Schirripa Spagnolo ◽  
Fabio Leccese
Keyword(s):  
Temperature Sensor ◽  
Energy Efficient ◽  
Light Emitting Diode ◽  
Junction Temperature ◽  
Light Emitting ◽  
Temperature Changes ◽  
Wide Range ◽  
International Regulations ◽  
Long Lifetime ◽  
Set Up

Nowadays, signal lights are made using light-emitting diode arrays (LEDs). These devices are extremely energy efficient and have a very long lifetime. Unfortunately, especially for yellow/amber LEDs, the intensity of the light is closely related to the junction temperature. This makes it difficult to design signal lights to be used in naval, road, railway, and aeronautical sectors, capable of fully respecting national and international regulations. Furthermore, the limitations prescribed by the standards must be respected in a wide range of temperature variations. In other words, in the signaling apparatuses, a system that varies the light intensity emitted according to the operating temperature is useful/necessary. In this paper, we propose a simple and effective solution. In order to adjust the intensity of the light emitted by the LEDs, we use an LED identical to those used to emit light as a temperature sensor. The proposed system was created and tested in the laboratory. As the same device as the ones to be controlled is used as the temperature sensor, the system is very stable and easy to set up.

scholarly journals Entropic measure unveils country competitiveness and product specialization in the World trade web

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Gianluca Teza ◽  
Michele Caraglio ◽  
Attilio L. Stella
Keyword(s):  
Iterative Scheme ◽  
Entropy Function ◽  
Bipartite Networks ◽  
Complexity Measures ◽  
Wide Range ◽  
Self Consistent ◽  
Set Up ◽  
Technical Features ◽  
Country Competitiveness ◽  
Entropic Measure

AbstractWe show how the Shannon entropy function can be used as a basis to set up complexity measures weighting the economic efficiency of countries and the specialization of products beyond bare diversification. This entropy function guarantees the existence of a fixed point which is rapidly reached by an iterative scheme converging to our self-consistent measures. Our approach naturally allows to decompose into inter-sectorial and intra-sectorial contributions the country competitivity measure if products are partitioned into larger categories. Besides outlining the technical features and advantages of the method, we describe a wide range of results arising from the analysis of the obtained rankings and we benchmark these observations against those established with other economical parameters. These comparisons allow to partition countries and products into various main typologies, with well-revealed characterizing features. Our methods have wide applicability to general problems of ranking in bipartite networks.

scholarly journals Membrane Lipid Composition of the Moderately Thermophilic Ammonia-Oxidizing Archaeon “Candidatus Nitrosotenuis uzonensis” at Different Growth Temperatures

2019 ◽  
Vol 85 (20) ◽  
Author(s):  
Nicole J. Bale ◽  
Marton Palatinszky ◽  
W. Irene C. Rijpstra ◽  
Craig W. Herbold ◽  
Michael Wagner ◽  
...  
Keyword(s):  
Lipid Composition ◽  
Strong Influence ◽  
Thermal Spring ◽  
Membrane Lipid ◽  
Effect Of Temperature ◽  
Environmental Niche ◽  
Membrane Lipid Composition ◽  
Moderately Thermophilic ◽  
Wide Range ◽  
Membrane Spanning

ABSTRACT “Candidatus Nitrosotenuis uzonensis” is the only cultured moderately thermophilic member of the thaumarchaeotal order Nitrosopumilales (NP) that contains many mesophilic marine strains. We examined its membrane lipid composition at different growth temperatures (37°C, 46°C, and 50°C). Its lipids were all membrane-spanning glycerol dialkyl glycerol tetraethers (GDGTs), with 0 to 4 cyclopentane moieties. Crenarchaeol (cren), the characteristic thaumarchaeotal GDGT, and its isomer (crenʹ) were present in high abundance (30 to 70%). The GDGT polar headgroups were mono-, di-, and trihexoses and hexose/phosphohexose. The ratio of glycolipid to phospholipid GDGTs was highest in the cultures grown at 50°C. With increasing growth temperatures, the relative contributions of cren and crenʹ increased, while those of GDGT-0 to GDGT-4 (including isomers) decreased. TEX86 (tetraether index of tetraethers consisting of 86 carbons)-derived temperatures were much lower than the actual growth temperatures, further demonstrating that TEX86 does not accurately reflect the membrane lipid adaptation of thermophilic Thaumarchaeota. As the temperature increased, specific GDGTs changed relative to their isomers, possibly representing temperature adaption-induced changes in cyclopentane ring stereochemistry. Comparison of a wide range of thaumarchaeotal core lipid compositions revealed that the “Ca. Nitrosotenuis uzonensis” cultures clustered separately from other members of the NP order and the Nitrososphaerales (NS) order. While phylogeny generally seems to have a strong influence on GDGT distribution, our analysis of “Ca. Nitrosotenuis uzonensis” demonstrates that its terrestrial, higher-temperature niche has led to a lipid composition that clearly differentiates it from other NP members and that this difference is mostly driven by its high crenʹ content. IMPORTANCE For Thaumarchaeota, the ratio of their glycerol dialkyl glycerol tetraether (GDGT) lipids depends on growth temperature, a premise that forms the basis of the widely applied TEX86 paleotemperature proxy. A thorough understanding of which GDGTs are produced by which Thaumarchaeota and what the effect of temperature is on their GDGT composition is essential for constraining the TEX86 proxy. “Ca. Nitrosotenuis uzonensis” is a moderately thermophilic thaumarchaeote enriched from a thermal spring, setting it apart in its environmental niche from the other marine mesophilic members of its order. Indeed, we found that the GDGT composition of “Ca. Nitrosotenuis uzonensis” cultures was distinct from those of other members of its order and was more similar to those of other thermophilic, terrestrial Thaumarchaeota. This suggests that while phylogeny has a strong influence on GDGT distribution, the environmental niche that a thaumarchaeote inhabits also shapes its GDGT composition.

Structural interpretation using refraction velocities from marine seismic surveys

Geophysics ◽  
1986 ◽  
Vol 51 (1) ◽  
pp. 12-19 ◽  
Author(s):  
James F. Mitchell ◽  
Richard J. Bolander
Keyword(s):  
Sedimentary Rock ◽  
Seismic Energy ◽  
Seismic Survey ◽  
Subsurface Structure ◽  
Seismic Reflection Data ◽  
Near Surface ◽  
Reflection Data ◽  
Wide Range ◽  
Streamer Length ◽  
Set Up

Subsurface structure can be mapped using refraction information from marine multichannel seismic data. The method uses velocities and thicknesses of shallow sedimentary rock layers computed from refraction first arrivals recorded along the streamer. A two‐step exploration scheme is described which can be set up on a personal computer and used routinely in any office. It is straightforward and requires only a basic understanding of refraction principles. Two case histories from offshore Peru exploration demonstrate the scheme. The basic scheme is: step (1) shallow sedimentary rock velocities are computed and mapped over an area. Step (2) structure is interpreted from the contoured velocity patterns. Structural highs, for instance, exhibit relatively high velocities, “retained” by buried, compacted, sedimentary rocks that are uplifted to the near‐surface. This method requires that subsurface structure be relatively shallow because the refracted waves probe to depths of one hundred to over one thousand meters, depending upon the seismic energy source, streamer length, and the subsurface velocity distribution. With this one requirement met, we used the refraction method over a wide range of sedimentary rock velocities, water depths, and seismic survey types. The method is particularly valuable because it works well in areas with poor seismic reflection data.

Reorientation of a single red blood cell during sedimentation

2016 ◽  
Vol 806 ◽  
pp. 102-128 ◽  
Author(s):  
D. Matsunaga ◽  
Y. Imai ◽  
C. Wagner ◽  
T. Ishikawa
Keyword(s):  
Angular Velocity ◽  
Blood Cell ◽  
Red Blood Cell ◽  
Blood Cells ◽  
Driving Force ◽  
Viscosity Ratio ◽  
Orientation Angle ◽  
Bond Number ◽  
Vertical Orientation ◽  
Main Factors

The reorientation phenomenon of a single red blood cell during sedimentation is simulated using the boundary element method. The cell settles downwards due to a density difference between the internal and external fluids, and it changes orientation toward a vertical orientation regardless of Bond number or viscosity ratio. The reorientation phenomenon is explained by a shape asymmetry caused by the gravitational driving force, and the shape asymmetry increases almost linearly with the Bond number. When velocities are normalised by the driving force, settling/drifting velocities are weak functions of the Bond number and the viscosity ratio, while the angular velocity of the reorientation drastically changes with these parameters: the angular velocity is smaller for lower Bond number or higher viscosity ratio. As a consequence, trajectories of the sedimentation are also affected by the angular velocity, and blood cells with slower reorientation travel longer distances in the drifting direction. We also explain the mechanism of the reorientation using an asymmetric dumbbell. From the analysis, we show that the magnitude of the angular velocity is explained by two main factors: the shape asymmetry and the instantaneous orientation angle.

Sign in / Sign up

Export Citation Format

Share Document