scholarly journals Fabrication Of Carbon Aerogels From Coir For Oil Adsorption

2022 ◽  
Vol 964 (1) ◽  
pp. 012033
Author(s):  
Hieu M Nguyen ◽  
Khoi A Tran ◽  
Tram T N Nguyen ◽  
Nga N H Do ◽  
Kien A Le ◽  
...  
Keyword(s):  
Freeze Drying ◽  
Oil Spills ◽  
Sol Gel ◽  
Urea Solution ◽  
Carbon Aerogels ◽  
Low Density ◽  
High Porosity ◽  
Motor Oil ◽  
Sol Gel Process ◽  
Oil Adsorption

Abstract Coir, known as coconut fibers, are an abundant cellulosic source in Vietnam, which are mostly discarded when copra and coconut water are taken, causing environmental pollution and waste of potential biomass. In this research, carbon aerogels from chemically pretreated coir were successfully synthesized via simple sol-gel process with NaOH-urea solution, economical freeze-drying, and carbonization. The samples, including pretreated coir, coir aerogels, and carbon aerogels, are characterized using FTIR spectroscopy, SEM, XRD spectroscopy, and TGA. The carbon aerogels exhibit low density (0.034–0.047 g/cm3), high porosity (97.63–98.32 %), and comparable motor oil sorption capacity (22.71 g/g). The properties of carbon aerogels are compared with those of coir aerogels, indicating such better values than those of coir aerogels. Coir-derived carbon aerogels is a potential replacement for the hydrophobically-coated cellulose aerogels in term of treating oil spills.

Mechanical Behavior of Bioactive Glass-Polyvinyl Alcohol Hybrid Foams Obtained by the Sol-Gel Process

2005 ◽  
Vol 284-286 ◽  
pp. 757-760 ◽  
Author(s):  
Marivalda Pereira ◽  
Showan N. Nazhat ◽  
Julian R. Jones ◽  
Larry L. Hench
Keyword(s):  
Polyvinyl Alcohol ◽  
Bioactive Glass ◽  
Mechanical Behavior ◽  
Sol Gel ◽  
Precursor Solution ◽  
High Porosity ◽  
Soft Tissue Regeneration ◽  
Sol Gel Process ◽  
Potential Applications ◽  
Hybrid Foams

The possibility of enhancing mechanical properties by incorporation of polymeric components to sol-gel derived materials is extremely attractive to prepare macroporous scaffolds, leading to materials with potential applications in both hard and soft tissue regeneration. In this work bioactive glass-polyvinyl alcohol hybrids were developed and their mechanical behavior was evaluated. Hybrids were synthesized by adding polyvinyl alcohol to a sol-gel precursor solution, which was then foamed with the addition of a surfactant and vigorous agitation. The foams were cast, aged and dried at 40°C. A cleaning step to decrease the acidic character of the obtained hybrids was undertaken by immersion in a NH4OH solution. The mechanical behavior of the hybrids was evaluated in compression using both stress and strain control tests. Hybrid foams had a high porosity varying from 60-90% and the macropore diameter ranged from 10 to 600 µm. The modal macropore diameter varied with the inorganic phase composition and with the polymer content in the hybrid. The strain at fracture of the as prepared hybrid foams was substantially greater than pure gel-glass foams. The cleaned hybrids presented a slightly higher strength and lower deformation than the as prepared foams.

Preparation of Silica Aerogels Monoliths from Hydrophobic Silica Gels and Pluronic10R5 via Sol–Gel Process

2020 ◽  
Vol 12 (2) ◽  
pp. 206-211
Author(s):  
Supattra Eangpayung ◽  
Supan Yodyingyong ◽  
Darapond Triampo
Keyword(s):  
Mass Loss ◽  
Propylene Oxide ◽  
Silica Aerogel ◽  
Sol Gel ◽  
Silica Aerogels ◽  
Silica Gels ◽  
High Porosity ◽  
Hydrophobic Silica ◽  
Sol Gel Process ◽  
Poly Propylene

Silica aerogel, the most common type of aerogels, comprised of 95% air in its structure which made the aerogel has a high surface area, high porosity, low density, and low thermal conductivity. Because of its structure and high porosity, one of its major weakness compared to other materials is being very brittle. This study aims at strengthening the connection points between silica nanoparticles using Pluronic10R5 (poly(propylene oxide)8–poly(ethylene oxide)22–poly(propylene oxide)8) where the Pluronic10R5 was used to reduce phase separation during the silica condensation reaction in the sol–gel process. Silica aerogel monoliths were prepared via a sol–gel process from hydrophobic silica gels and Pluronic10R5 with an ambient pressure drying (APD) process. Results from the compression test showed that the Pluronic10R5/silica aerogels have improved mechanical property by ten times that of unmodified silica aerogels. A thermogravimetric analysis (TGA) showed a mass loss at 300–400 °C that is attributed to the surface methyl group, while a mass loss at 200 °C refers to the loss of Pluronic10R5 which confirms the incorporation of Pluronic10R5 into the monolith. Moreover, infrared (IR) images revealed that the top surface temperature of Pluronic10R5/silica aerogels monolith is about 80 °C differs from the bottom heat source temperature of 160 °C.

Performance Study and Structure Control of Carbon Aerogel

2013 ◽  
Vol 706-708 ◽  
pp. 897-900 ◽  
Author(s):  
Rui He ◽  
Xuan Liu ◽  
Zhen Fa Liu ◽  
Li Hui Zhang
Keyword(s):  
High Surface ◽  
Sol Gel ◽  
Supercritical Drying ◽  
Carbon Aerogel ◽  
Preparation Condition ◽  
Carbon Aerogels ◽  
Performance Study ◽  
Structure Control ◽  
Sol Gel Process ◽  
Nanopore Structure

In this research the fabrication of carbon aerogel is reported. nanopore carbon aerogels were prepared via a sol-gel process with resorcinol and formaldehyde (RF) aerogels,which were cost-effectively manufacture form Rf wet gels by an ambient drying technique instead of conventional supercritical drying. The key of the work is to fabricate carbon aerogels with controllable nanopore structure, which means sharp pore size distribution and extremely high surface area.The influence of preparation condition of carbon aerogels was studied by scanning electron microscope and Micropore Physisorption Analyzer. The BET surface of the carbon aerogels are from 749m2/g to 1156m2/g .The size of the carbon nanoparticles are in the range of 20nm~40nm. The micro-pore volume and bore diameter can be controlled by gelation conditions such as RF mass fraction.

Preparation and Characterization of Phloroglucinol-Resorcinol-Formaldehyde Carbon Aerogels

2013 ◽  
Vol 423-426 ◽  
pp. 523-527
Author(s):  
Xuan Liu ◽  
Zhen Fa Liu ◽  
Hao Lin Fu ◽  
Rui He ◽  
Li Hui Zhang
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
High Specific Surface Area ◽  
Carbon Aerogels ◽  
Resorcinol Formaldehyde ◽  
Sol Gel Process ◽  
Solvent Replacement ◽  
Organic Aerogels

Phloroglucinol-resorcinol-formaldehyde organic aerogels (PRF) were prepared using phloroglucinol, resorcinol and formaldehyde in a sol-gel process, solvent replacement and drying at room temperature. The phloroglucinol-resorcinol-formaldehyde carbon aerogels (CPRF) were prepared by charring the PRF at high temperature under the aegis of helium flow. The microstructure of CPRF was characterized by infrared spectroscopy, specific surface area analyzer and scanning electron microscopy. The results showed that the CPRF had continuous network structure and high specific surface area.

Facile synthesis of monolithic mayenite with well-defined macropores via an epoxide-mediated sol–gel process accompanied by phase separation

2014 ◽  
Vol 38 (12) ◽  
pp. 5832-5839 ◽  
Author(s):  
Xingzhong Guo ◽  
Xiaobo Cai ◽  
Jie Song ◽  
Yang Zhu ◽  
Kazuki Nakanishi ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Phase Separation ◽  
Sol Gel ◽  
High Porosity ◽  
Macroporous Structure ◽  
Facile Synthesis ◽  
Sol Gel Process

Monolithic mayenite has been successfully prepared via a sol–gel process followed by heat-treatment, exhibiting co-continuous macroporous structure and high porosity.

Manufactory and Properties of Poly(p-Phenylenebenzobisoxazole) Aerogels Prepared by a Simple Freeze-Drying Procedure

2020 ◽  
Vol 993 ◽  
pp. 662-668
Author(s):  
Yu Nong Wei ◽  
Guang Li ◽  
Sheng Lin Yang ◽  
Jun Hong Jin
Keyword(s):  
High Performance ◽  
Freeze Drying ◽  
Sol Gel ◽  
Fire Retardant ◽  
Decomposition Temperature ◽  
High Specific Surface Area ◽  
High Porosity ◽  
Cellulose Aerogel ◽  
Small Pore ◽  
Small Pore Diameter

Aerogels based on organic high performance fibers have been attracted great attention due to its excellent thermal and mechanical properties. Here, PBO nanofiber aerogel were prepared from the super-fiber PBO through a top-down process with a sol-gel process and a simple freeze-drying process, followed by thermal cross-linking. The prepared aerogel has a small volume shrinkage, a high specific surface area of 168.9 m2 /g and a small pore diameter of 1.356 nm. Because of its 3D porous structure, it results in a low density of 6 to 30 mg/cm3 and a high porosity (98%). The aerogel retains the molecular structure of PBO at the same time, which gives it initial thermal decomposition temperature up to 500 °C and a superior fire-retardant capability. PBO aerogel possesses good compressive properties with a yield stress of 0.44MPa at 80% strain and an elasticity modulus of 1.98 MPa which is higher than SiO2 and cellulose aerogel reported.

Organic Biodegradable Aerogels Used in Controlled Drug Release

2011 ◽  
Vol 1306 ◽  
Author(s):  
Anja Veronovski ◽  
Zoran Novak ◽  
Knez Željko
Keyword(s):  
Drug Delivery ◽  
Drug Release ◽  
Nicotinic Acid ◽  
Sol Gel ◽  
Supercritical Drying ◽  
Diffusion Method ◽  
Cross Linking ◽  
High Porosity ◽  
Alginate Solution ◽  
Sol Gel Process

ABSTRACTThere are a lot of synthetic polymers which can be used for controlled drug delivery, however they are not easily accepted by the organism. Also incorporation of drugs into carriers runs under difficult conditions. Therefore scientists have been inclined to use natural-origin polymers, such as proteins and polysaccharides. Some of these promising natural polysaccharidic candidates are alginic acid sodium salt, guar gum and chitosan due to their outstanding merits. They are similar to extracellular matrix having high chemical versatility, good biological performance and cell or enzyme-controlled degradability. Many polysaccharidic hydrogels for drug delivery have already been prepared, but one of their weakness is their short life in dry air conditions; thus, special coating materials are being developed for enhancing their life time.Alginates were used in the present research for synthesis of organic biodegradable gels by sol-gel process, which were further easily converted to aerogels by supercritical drying. They are safe for use, nontoxic, and derived from renewable sources. Aerogels made of alginate are dry and stable materials, which makes them interesting as a substitute to hydrogels. Alginates undergo reversible gelation in aqueous solution through interaction with divalent cations such as Ca2+, which create ionic inter-chain bridges. Two fundamental methods of ionic cross-linking were used to prepare alginate hydrogels: the diffusion method, where spheres are created and the internal setting method resulting in monoliths. After producing the hydrogel, alcogels were formed by solvent exchange using 100% ethanol. Ethanol was later replaced by supercritical CO2 with supercritical drying (100 bar, 35°C). Aerogels made from natural polysaccharides combine both biocharacteristics and aerogel characteristics such as high porosity and specific surface area, which makes them really attractive in drug delivery applications. The aerogels obtained in present research were therefore studied as drug carriers. The effects of the alginate composition and synthesis method on model drug nicotinic acid release were investigated. The results indicated that by using the internal setting cross-linking method for obtaining aerogels nicotinic acid was released in a more controlled manner. That is why further investigation was done on alginate spherical beads for prolonging their drug release. A multi-step sol-gel process was applied to generate complex aerogels with multi-membranes. First ionically cross-linked spherical cores were obtained by dropwise addition of sodium alginate solution into a CaCl2 solution. These cores were further immersed into alginate solution, filtered through a sieve and dropped into a salt solution again. By repeating the above process, different multi-membrane hydrogels were produced and further converted to aerogels. By adding more membranes around core burst drug release was successfully inhibited.

Effects of Surfactants on the Synthesis of Silica Aerogels Prepared by Ambient Pressure Drying

2012 ◽  
Vol 512-515 ◽  
pp. 1625-1630
Author(s):  
Hua Zheng Sai ◽  
Li Xing ◽  
Jun Hui Xiang ◽  
Fu Shi Zhang ◽  
Li Jie Cui ◽  
...  
Keyword(s):  
Ambient Pressure ◽  
Sol Gel ◽  
Drying Shrinkage ◽  
Silica Aerogels ◽  
Ambient Pressure Drying ◽  
Ammonium Bromide ◽  
High Porosity ◽  
Free Silica ◽  
Sol Gel Process ◽  
Cetyltrimethyl Ammonium

In this research, aerogels were synthesized by a two-step sol-gel process without supercritical conditions. During the process, tetraethoxysilane (TEOS) was used as precursor, and different surfactants, i.e. cetyltrimethyl ammonium bromide (CTAB) and polyethylene glycol–600 (PEG–600), were used as dopants respectively. In order to minimize the drying shrinkage and preserve the high porosity structure, the surface of the gels was modified by trimethylchlorosilane (TMCS) before the ambient pressure drying (APD). The effect of surfactent on the structure of the resulting aerogels was investigated. The aerogels which involved surfactants exhibited resistance to cracking during the APD of the alcogels. The modification by TMCS has been confirmed using Infrared (IR) spectroscopy. The porous structure of aerogels was investigated by Brunauer-Emmett- Teller (BET) instrument, differential scanning calorimeter (DSC) and scanning electron micrograph (SEM). The results indicated that surfactants as dopants could significantly affect the structure and optical property of aerogels and be beneficial for obtaining crack-free silica aerogels via ambient pressure drying process.

Bioactive Gelatin-Siloxane Hybrids as Tissue Engineering Scaffold

2006 ◽  
Vol 111 ◽  
pp. 13-18 ◽  
Author(s):  
Lei Ren ◽  
Akiyoshi Osaka ◽  
B. Yu ◽  
Wei Shi ◽  
Dong Tao Ge ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Freeze Drying ◽  
Ph Value ◽  
Sol Gel ◽  
Freezing Temperature ◽  
Structure Change ◽  
Pore Characteristics ◽  
Biodegradable Scaffolds ◽  
Antibiotic Drug ◽  
Sol Gel Process

Ca2+-containing porous gelatin-siloxane hybrids were prepared using sol-gel process, post-gelation soaking, and freeze-drying. The porosity and pore size of the hybrids could be well controlled by the freezing temperature and the pH value of the soaking solution. The pore characteristics were related to the structure change during the soaking treatment. A bone-like apatite layer was able to form in the Ca2+-containing porous gelatin-siloxane hybrids upon soaking in a stimulated body fluid. The porous gelatin-siloxane hybrids could release gentamicin sulfate which is an antibiotic drug in bone chemotherapy. Thus, those hybrid materials are proposed to find application as novel bioactive and biodegradable scaffolds in bone tissue engineering.

scholarly journals Experiences with Sol-Gel Bonded High Porosity Alumina Fiber Materials for Filter Applications

1988 ◽  
Vol 121 ◽  
Author(s):  
Karin E. Handrick ◽  
August Mohlratzer ◽  
Rolf Ostertag ◽  
Dieter Sporn ◽  
Helmut Schmidt
Keyword(s):  
Gas Flow ◽  
Porous Alumina ◽  
Sol Gel ◽  
High Porosity ◽  
Alumina Fiber ◽  
Gas Filtration ◽  
Ceramic Binder ◽  
Sol Gel Process ◽  
Fiber Materials ◽  
The Stability

ABSTRACTHigh porous alumina fiber structures appear promising for hot gas filtration in particular for diesel particulate traps. For this purpose, however, a method is required for manufacturing of stable shapes resistant to the blow-out by the gas flow. The sol-gel-process was expected to be the best suited method for fiber bonding to provide the required stability.The main tasks of the development-work were a uniform isotropie fiber-distribution, the adaptation of the sol-gel-process to the application, and the deliberate synthesis of the gel-derived alumina bonding phase.The appropriate fibrous structure was obtained by a repeated filtration of sol/fiber suspensions. The properties of the ceramic binder were adapted by concentrating the sol and/or adding aluminas or aluminium hydroxides.Testing of prototypes with optimized structures has shown, however, that the stability of the structure decreased after thermal load. The thermal fatigue of x-A12O3 is assumed to be responsible for this failure.

Sign in / Sign up

Export Citation Format

Share Document