scholarly journals Feasibility study of concrete by using polyethylene terephthalate fiber in enhancing the mechanical properties of concrete

2021 ◽  
Vol 1197 (1) ◽  
pp. 012041
Author(s):  
Kartik D Rathod ◽  
Isha Khedikar ◽  
Kuldeep Dabhekar
Keyword(s):  
Mechanical Property ◽  
Compressive Strength ◽  
Polyethylene Terephthalate ◽  
Solid Waste Management ◽  
Direct Method ◽  
Glass Fibers ◽  
Dry Density ◽  
Chemical Attack ◽  
Compressive Strength Test ◽  
Health Related

Abstract In these project Polyethylene terephthalate fiber (PET) fibers are use to improve the mechanical property of concrete and minimize the environmental pollution of earth. PET is use to prepare container for water, cold drinks, food etc. which is single used and it thrown in to the sea, dump on free land and burning. It cause many serious effect on animals, sea animals, destroy land fertility and other health related issues. The PET material are used to improve mechanical property of concrete like compressive strength, dry and wet density and static and dynamic elastic modulus. Thus fibers are available in natural and artificial material. Now a days, artificial fibers are widely used in India. The types of fibers are plastic fibers, glass fibers, steel fibers etc. In India according to solid waste management data is 15,350 tons daily and 1,84,120 tons annually generate, but only 9,350 tons daily and 1,12,120 tons annually collected. So the uncollected data is that about 6000 tons daily and 72,000 tons annually uncollected, in such a way that it causes many problems to the atmosphere so that it becomes environmentally harmful. For developing country concrete is most important material. It is extensively used in construction industry. Concrete have many advantages like long service life, durability, chemical attack resistance etc. Thus concrete has some many disadvantage like low tensile strength, flexural strength and cracks. To overcome these disadvantage add some supplements in concrete to improve its strength. The fiber are one of them. It reduces environmental problem it becomes eco-friendly. In case of compressive strength test, wet density test and direct method of UPV result are obtain as concrete carry higher applied load also it give high compressive strength, high wet and dry density of concrete and quality of concrete is good when adding 0.4% of shape - 01 PET fiber in concrete.

scholarly journals Comparison of Compressive Strength of Concrete by Partial Replacement of Cement with GGBS and Silica Fume with Sea Water Curing and Addition with Fibers

2021 ◽  
pp. 31-39
Author(s):  
A Aswani and Janardhan G
Keyword(s):  
Compressive Strength ◽  
Silica Fume ◽  
Sea Water ◽  
Glass Fibers ◽  
Vital Role ◽  
Strength Test ◽  
Partial Replacement ◽  
Compressive Strength Test ◽  
Water Curing ◽  
Compressive Strength Of Concrete

In construction world concrete plays a vital role, around 60% of structure consists of Concrete. However, the production of Portland cement, an essential constituent of concrete, leads to the release of significant amounts of CO2, depletion of natural resources and environmental degradation. This paper investigates the compressive strength of concrete by replacing cement with GGBS and silica fume effect of glass fibers on performance of concrete is studied. In this present work a humble attempt had been made to evaluate and compare the compressive strengths of GGBS blended concrete cubes with controlled concrete cubes cured under sea water for 28 days. By conducting the tests on the cubes, conclusions were drawn after plotting and analyzing the results. Compressive strength test is conducted on the samples after 28 days. The optimum value is obtained at 15% replacement with GGBS and 5% with Silica fume. In this study again we trailed addition with Glass fibers with the percentage of 0.5%,1.0%,1.5%, compressive strength have been studied. Finally at 1.0% addition we get maximum strength compared to controlled mix.

scholarly journals PERBANDINGAN KUAT TEKAN BATA PLASTIK BERJENIS POLYPROPYLENE (PP) POLYETHYLENE TEREPHTHALATE (PET) DAN HIGH DENSITY POLYETHYLENE (HDPE)

2021 ◽  
Vol 9 (1) ◽  
pp. 019
Author(s):  
Muhammad Ridho Reksi ◽  
Dian Rahayu Jati ◽  
Yulisa Fitrianingsih
Keyword(s):  
Compressive Strength ◽  
Polyethylene Terephthalate ◽  
High Density Polyethylene ◽  
Strength Test ◽  
High Density ◽  
Raw Material ◽  
Selling Price ◽  
Purchase Price ◽  
Compressive Strength Test ◽  
Markup Pricing

AbstractPlastic waste needs attention because it can cause serious problems if not managed properly. Of the various types of plastics, the most widely disposed of to the environment are Polypropylene, Polyethylene Terephthalate, and High-Density Polyethylene which are usually in the form of plastic bags and bottles. This research was conducted to make bricks made of plastic as an alternative material for infrastructure that is economical, strong, and durable, which is seen based on the compressive strength value based on its type, namely PP, PET, and HDPE plastic bricks. The compressive strength testing phase is carried out three times in each type. The selling price of plastic bricks is determined by the Markup pricing method. The process of plastic brick making includes collecting plastic waste, washing, drying, chopping, melting, and printing. Based on the research results, the plastic bricks produced from the types of PET, HDPE, and PP are in the form of blocks with a size of 19 cm x 10 cm x 6.5 cm, where the PET type brick requires 5.1 kg of waste, 3.6 kg of HDPE type, and the type of PP as much as 3 kg. The compressive strength test values for PP, PET, and HDPE plastic bricks have met the compressive strength standards based on SNI 15-2094-2000, with the highest average compressive strength test values found in PP plastic bricks of 246 kg/cm², plastic bricks HDPE type 166 kg/cm², and plastic brick type PET 98.7 kg/cm². The selling price of plastic bricks without including the purchase price of plastic as raw material for making plastic bricks (Scenario I) for PP plastic bricks costs Rp1.907,00/brick, PET types Rp3.024,00/brick, and HDPE types Rp3.464,00/brick. While the selling price of plastic bricks by entering the purchase price of plastic as raw material for making plastic bricks (Scenario II) for PP plastic bricks Rp2.867,00/brick, PET type Rp4.624,00/brick, and HDPE type Rp3.944,00/brick.Keywords: Compressive Strength, Markup Pricing, Plastic Brick. AbstrakSampah plastik perlu mendapatkan perhatian karena menimbulkan masalah yang serius jika tidak dikelola dengan baik. Dari berbagai jenis plastik, yang paling banyak dibuang ke lingkungan adalah jenis Polypropylene, Polyethylene Terephthalate, dan High Density Polyethylene yang biasanya dalam bentuk kantong dan botol plastik. Penelitian ini dilakukan guna membuat bata berbahan plastik sebagai bahan alternatif infrastruktur yang bersifat ekonomis, kuat dan tahan lama yang dilihat berdasarkan nilai kuat tekan berdasarkan jenisnya, yaitu bata plastik jenis PP, PET, dan HDPE. Tahap pengujian kuat tekan dilakukan sebanyak tiga kali pengulangan di setiap jenisnya. Harga jual bata plastik ditentukan dengan metode Markup pricing. Proses pembuatan bata plastik yaitu pengumpulan sampah plastik, pencucian, penjemuran, pencacahan, pelelehan, dan pencetakan. Berdasarkan hasil penelitian, bata plastik yang dihasilkan dari jenis PET, HDPE, dan PP berbentuk balok dengan ukuran 19 cm x 10 cm x 6,5 cm, dimana bata jenis PET memerlukan sampah sebanyak 5,1 kg, jenis HDPE sebanyak 3,6 kg, dan  jenis PP sebanyak 3 kg. Nilai uji kuat tekan pada bata plastik jenis PP, PET, dan HDPE telah memenuhi standar kuat tekan berdasarkan SNI 15-2094-2000, dengan nilai uji kuat tekan rata-rata tertinggi terdapat pada bata plastik jenis PP sebesar 246 kg/cm², bata plastik jenis HDPE 166 kg/cm², dan bata plastik jenis PET 98,7 kg/cm². Harga jual bata plastik tanpa memasukkan harga beli plastik sebagai bahan baku pembuatan bata plastik (Skenario I) pada bata plastik jenis PP seharga Rp1.907,00/bata, jenis PET Rp3.024,00/bata, dan jenis HDPE Rp3.464,00/bata. Sedangkan harga jual bata plastik dengan memasukkan harga beli plastik sebagai bahan baku pembuatan bata plastik (Skenario II) pada bata plastik jenis PP Rp2.867,00/bata, jenis PET Rp4.624,00/bata, dan jenis HDPE Rp3.944,00/bata.Kata Kunci: Bata Plastik, Kuat Tekan, Markup Pricing.

scholarly journals Acid and Base Attack on Concrete by Partial Replacement of Cement with GGBS, Silica Fume and Addition with Fibers

2021 ◽  
Vol 7 (03) ◽  
pp. 44-51
Author(s):  
M Satya Himabindu and S Naveen Kumar
Keyword(s):  
Compressive Strength ◽  
Natural Resources ◽  
Silica Fume ◽  
Glass Fibers ◽  
Vital Role ◽  
Strength Test ◽  
Partial Replacement ◽  
Compressive Strength Test ◽  
Acid And Base ◽  
Compressive Strength Of Concrete

In construction world concrete plays a vital role, around 60% of structure consists of Concrete. However, the production of Portland cement, an essential constituent of concrete, leads to the release of significant amounts of CO2, depletion of natural resources and environmental degradation. This paper investigates the compressive strength of concrete by replacing cement with GGBS and silica fume effect of glass fibers on performance of concrete is studied. In this present work a humble attempt had been made to evaluate and compare the compressive strengths of GGBS blended concrete cubes with controlled concrete cubes cured under ACID and BASE for 28 days. By conducting the tests on the cubes, conclusions were drawn after plotting and analyzing the results. Compressive strength test is conducted on the samples after 28 days. The optimum value is obtained at 15% replacement with GGBS and 5% with Silica fume. In this study again we trailed addition with Glass fibers with the percentage of 0.5%,1.0%,1.5%, compressive strength have been studied. Finally at 1.0% addition we get maximum strength compared to controlled mix

scholarly journals Conceptualization and Design of a Small Pyrolysis Plant for the Sustainable Production of Flexible Bricks and Bituminous Concrete from Polyethylene Terephthalate Waste

2021 ◽  
Author(s):  
Ngonidzashe L. Shangwa ◽  
Wilson R. Nyemba ◽  
Simon Chinguwa ◽  
Tien-Chien Jen
Keyword(s):  
Compressive Strength ◽  
Polyethylene Terephthalate ◽  
Construction Materials ◽  
Road Construction ◽  
Calorific Value ◽  
Raw Material ◽  
Chemical Attack ◽  
Proper Disposal ◽  
Bituminous Concrete

Polyethylene terephthalate is majorly used for packaging of various products because of its resistance to chemical attack and environmental degradation, but the proper disposal of this non-biodegradable material has been a major challenge. Pyrolysis is the melting of plastic in the absence of oxygen. Currently pyrolysis of polyethylene terephthalate is considered as a viable recycling method since it only requires 5% of the calorific value of polyethylene terephthalate. This research was aimed at designing a pyrolysis plant for the production of construction materials with acceptable mechanical properties such as compressive strength and water absorption. Sustainable, eco-friendly road construction from bituminous concrete with waste polyethylene terephthalate has the capability of reducing carbon emissions. The polyethylene terephthalate bituminous composite has the flexibility of plastic but strength of concrete. The bricks have a maximum compressive strength of 10 N/mm2 which is within the standard range and have less water absorbing tendencies hence have a longer lifespan. Value addition is equally important in the pyrolysis plant so as to contribute to sustainable development. This book chapter reviews the different products such as polyethylene terephthalate composite bricks and flexible pavements which can effectively use polyethylene terephthalate waste as a raw material.

Improvement of Soil by Using Natural Material (JUTE AND GYPSUM)

2021 ◽  
Vol 9 (8) ◽  
pp. 2254-2258
Author(s):  
Zahid Hussain Shapoo
Keyword(s):  
Compressive Strength ◽  
Clayey Soil ◽  
Engineering Properties ◽  
Natural Material ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Compressive Strength Test ◽  
Proctor Test ◽  
Varying Length ◽  
Standard Proctor Test

Abstract: Generally clay exhibits undesirable engineering properties like poor bearing capacity and higher compressibility. Thus the improvement of the soil at site is indispensable. There are many stabilizers to improve the strength of soil like Jute, Gypsum, fly ash, rice husk ash, cement, lime used rubber tyres etc. In the present Study , we added jute and gypsum as stabilizer to improve the properties of clayey soil . Locally available clayey soil is used in this study . The objective of this study is to improve the strength of the clayey soil by making soil-jute and soil-jute-gypsum mixture. six specimens are prepared to investigate the properties of soil out of which three specimens are prepared by adding 1% of jute with varying length of 1cm,2cm and 3cm and the remaining three specimens are prepared by adding 1% jute and gypsum each with varying length of 1cm,2cm and 3cm of jute . Standard proctor test and unconfined compressive strength test are conducted to analyse the optimum moisture content (OMC), Maximum dry density (MDD) and compressive strength of soil mixture.

scholarly journals Peat Stabilization using Gypsum and Fly Ash

2010 ◽  
Vol 1 (2) ◽  
pp. 1-5 ◽  
Author(s):  
Kolay P.K. ◽  
Pui M.P.
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Unconfined Compressive Strength ◽  
Peat Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Compressive Strength Test ◽  
Proctor Test ◽  
Ucs Test ◽  
Standard Proctor Test

This paper presents the stabilization of local peat soil from Matang, Sarawak, using gypsum and fly ash. Peat soil has been identified as one of the major groups of soils found in Malaysia, which has high compressibility and low shear strength. Presence of soft or peaty soil is a major problem encountered by civil engineers in Sarawak. Different percentages of gypsum (i.e., 2, 4, 6 and 8%) and fly ash (i.e., 5, 10, 15, 20 and 25%) were added into peat soil at optimum moisture content and it’s maximum dry density determined by standard Proctor test. Unconfined compressive strength (UCS) test were conducted to determine the strength gain after 7, 14 and 28 days of curing periods. Physical properties of the peat soil have also been studied for identification and classification purposes. The unconfined compressive strength test results show that the peat soil gained strength due to the addition of different percentages of admixtures such as gypsum and fly ash and the strength also increases with the increase of curing periods.

The influence of the addition of ground olive stone on the thermo-mechanical behavior of compressed earth blocks

2020 ◽  
Vol 108 (2) ◽  
pp. 203
Author(s):  
Samia Djadouf ◽  
Nasser Chelouah ◽  
Abdelkader Tahakourt
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Mechanical Behavior ◽  
Agricultural Waste ◽  
Hydraulic Press ◽  
Dry Density ◽  
Olive Stone ◽  
Compressed Earth Blocks ◽  
Clay Matrix ◽  
Earth Blocks

Sustainable development and environmental challenges incite to valorize local materials such as agricultural waste. In this context, a new ecological compressed earth blocks (CEBS) with addition of ground olive stone (GOS) was proposed. The GOS is added as partial clay replacement in different proportions. The main objective of this paper is to study the effect of GOS levels on the thermal properties and mechanical behavior of CEB. We proceeded to determining the optimal water content and equivalent wet density by compaction using a hydraulic press, at a pressure of 10 MPa. The maximum compressive strength is reached at 15% of the GOS. This percentage increases the mechanical properties by 19.66%, and decreases the thermal conductivity by 37.63%. These results are due to the optimal water responsible for the consolidation and compactness of the clay matrix. The substitution up to 30% of GOS shows a decrease of compressive strength and thermal conductivity by about 38.38% and 50.64% respectively. The decrease in dry density and thermal conductivity is related to the content of GOS, which is composed of organic and porous fibers. The GOS seems promising for improving the thermo-mechanical characteristics of CEB and which can also be used as reinforcement in CEBS.

scholarly journals Alkali-Activated Zeolite 4A Granules—Characterization and Suitability Assessment for the Application of Adsorption

Crystals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 360
Author(s):  
Pauls P. Argalis ◽  
Laura Vitola ◽  
Diana Bajare ◽  
Kristine Vegere
Keyword(s):  
Compressive Strength ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Morphological Properties ◽  
Solid Ratio ◽  
Suitability Assessment ◽  
Bet Analysis ◽  
Zeolite 4A ◽  
Compressive Strength Test ◽  
Alkali Activated

A major problem in the field of adsorbents is that binders (kaolin clay, bentonite) introduced to bind zeolites and ensure the needed mechanical strength, are not able to sorb gases like CO2 and N2, and decrease the overall adsorption capacity. To solve this problem, one of the pathways is to introduce a binder able to sorb such gases. Thus, in this study, the physical and mechanical properties of a novel binder based on metakaolin and its composite with zeolite 4A in the granular form were studied. Metakaolin was used as a precursor for alkali-activated binder, which was synthesized using an 8M NaOH activation solution. Raw materials were characterized using granulometry, X-ray diffraction (XRD), and differential thermal analysis (DTA); and final products were characterized using density measurements, a compressive strength test, XRD, Brunauer–Emmett–Teller (BET) analysis, and scanning electron microscopy (SEM). Alkali-activated metakaolin was found to be efficient as a binding material when data for morphological properties were analyzed. A relationship was observed—by increasing the liquid-to-solid ratio (L/S), compressive strength decreased. Zeolite granule attrition was higher than expected: 2.42% and 4.55% for ZG-0.8, 3.64% and 5.76% for ZG-1.0, and 2.73% and 4.85% for ZG-1.2, measured at 4 and 5 atmospheres, respectively.

scholarly journals Characterization and Comparison Research on Composite of Alluvial Clayey Soil Modified with Fine Aggregates of Construction Waste and Fly Ash

2021 ◽  
Vol 28 (1) ◽  
pp. 83-95
Author(s):  
Qu Jili ◽  
Wang Junfeng ◽  
Batugin Andrian ◽  
Zhu Hao
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Unconfined Compressive Strength ◽  
Clayey Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Construction Waste ◽  
Comparison Research ◽  
Fine Aggregates ◽  
Optimum Water Content

Abstract Fine aggregates of construction waste and fly ash were selected as additives to modify the characteristics of Shanghai clayey soil as a composite. The laboratory tests on consistency index, maximum dry density, and unconfined compressive strength were carried out mainly for the purpose of comparing the modifying effect on the composite from fine aggregates of construction waste with that from fly ash. It is mainly concluded from test results that the liquid and plastic limit of the composites increase with the content of two additives. But their maximum dry density all decreases with the additive content. However, fine aggregates of construction waste can increase the optimum water content of the composites, while fly ash on the contrary. Finally, although the two additive all can increase the unconfined compressive strength of composites, fly ash has better effect. The current conclusions are also compared with previous studies, which indicates that the current research results are not completely the same as those from other researchers.

Mechanical Property of Phosphoaluminate Cement

2010 ◽  
Vol 150-151 ◽  
pp. 1754-1757 ◽  
Author(s):  
Peng Liu ◽  
Zhi Wu Yu ◽  
Ling Kun Chen ◽  
Zhu Ding
Keyword(s):  
Mechanical Property ◽  
Compressive Strength ◽  
Phase Composition ◽  
Electrical Properties ◽  
Pore Size Distribution ◽  
Pore Size ◽  
High Strength ◽  
Curing Time ◽  
Hydration Products ◽  
Resistance Value

The influence of curing time on the mechanical property of the phosphoaluminate cement (PAC) was investigated, and the mechanism was discussed as well. The phase composition and morphology of hydration products, electrical properties, porosity and pore size distribution of PAC cured different age were analyzed with XRD, EIS and MIP. The results showed PAC has the property of early-high strength, and the compressive strength of PAC cured for 1 day was about 70% of 28 days’. The main hydration products of PAC are micro-crystal phase and gel of phosphate and phosphoaluminate which formed compacter microstructure. In addition, there are no calcium hydroxide (CH) and ettringite (AFt) produced during the process of hydration. The compressive strength of PAC increased with age, which was due to more products continuously produced. The ac resistance analysis manifested as the change of the nyquist pattern and resistance value.

Sign in / Sign up

Export Citation Format

Share Document