The Influence of Metal Plating of Chip Carriers on Reliability of SMT Solder Joints under Thermal Cycling

1993 ◽  
Vol 5 (3) ◽  
pp. 18-20
Author(s):  
J.H. Huang ◽  
H.Z. Li
Keyword(s):  
Thermal Cycling ◽  
Solder Joints ◽  
Metal Plating

scholarly journals Microstructure and shear properties of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints under thermal cycling

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Jianguo Cui ◽  
Keke Zhang ◽  
Di Zhao ◽  
Yibo Pan
Keyword(s):  
Shear Strength ◽  
Thermal Cycling ◽  
Solder Joints ◽  
High Reliability ◽  
Sharp Decrease ◽  
Thermal Shock Test ◽  
Shear Properties ◽  
Equivalent Time ◽  
Ultrasonic Assisted ◽  
Reliability Of Solder Joints

AbstractThrough ultrasonic wave assisted Sn2.5Ag0.7Cu0.1RExNi/Cu (x = 0, 0.05, 0.1) soldering test and − 40 to 125 °C thermal shock test, the microstructure and shear properties of Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints under thermal cycling were studied by the SEM, EDS and XRD. The results show that the Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints with high quality and high reliability can be obtained by ultrasonic assistance. When the ultrasonic vibration power is 88 W, the ultrasonic-assisted Sn2.5Ag0.7Cu0.1RE0.05Ni/Cu solder joints exhibits the optimized performance. During the thermal cycling process, the shear strength of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints had a linear relationship with the thickness of interfacial intermetallic compound (IMC). Under the thermal cycling, the interfacial IMC layer of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints consisted of (Cu,Ni)6Sn5 and Cu3Sn. The thickness of interfacial IMC of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints was linearly related to the square root of equivalent time. The growth of interfacial IMC of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints had an incubation period, and the growth of IMC was slow within 300 cycles. And after 300 cycles, the IMC grew rapidly, the granular IMC began to merge, and the thickness and roughness of IMC increased obviously, which led to a sharp decrease in the shear strength of the solder joints. The 0.05 wt% Ni could inhibit the excessive growth of IMC, improve the shear strength of solder joints and improve the reliability of solder joints. The fracture mechanism of ultrasonic-assisted Sn2.5Ag0.7Cu0.1RExNi/Cu solder joints changed from the ductile–brittle mixed fracture in the solder/IMC transition zone to the brittle fracture in the interfacial IMC.

scholarly journals Study on the Reliability of Sn–Bi Composite Solder Pastes with Thermosetting Epoxy under Thermal Cycling and Humidity Treatment

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 733
Author(s):  
Lu Liu ◽  
Songbai Xue ◽  
Ruiyang Ni ◽  
Peng Zhang ◽  
Jie Wu
Keyword(s):  
Solder Joint ◽  
Thermal Cycling ◽  
Composite Solder ◽  
Solder Joints ◽  
Solder Paste ◽  
Epoxy System ◽  
Mechanical Reinforcement ◽  
Microstructure Observation ◽  
Temperature And Humidity ◽  
Thermosetting Epoxy

In this study, a Sn–Bi composite solder paste with thermosetting epoxy (TSEP Sn–Bi) was prepared by mixing Sn–Bi solder powder, flux, and epoxy system. The melting characteristics of the Sn–Bi solder alloy and the curing reaction of the epoxy system were measured by differential scanning calorimeter (DSC). A reflow profile was optimized based on the Sn–Bi reflow profile, and the Organic Solderability Preservative (OSP) Cu pad mounted 0603 chip resistor was chosen to reflow soldering and to prepare samples of the corresponding joint. The high temperature and humidity reliability of the solder joints at 85 °C/85% RH (Relative Humidity) for 1000 h and the thermal cycle reliability of the solder joints from −40 °C to 125 °C for 1000 cycles were investigated. Compared to the Sn–Bi solder joint, the TSEP Sn–Bi solder joints had increased reliability. The microstructure observation shows that the epoxy resin curing process did not affect the transformation of the microstructure. The shear force of the TSEP Sn–Bi solder joints after 1000 cycles of thermal cycling test was 1.23–1.35 times higher than the Sn–Bi solder joint and after 1000 h of temperature and humidity tests was 1.14–1.27 times higher than the Sn–Bi solder joint. The fracture analysis indicated that the cured cover layer could still have a mechanical reinforcement to the TSEP Sn–Bi solder joints after these reliability tests.

A Highly Accelerated Thermal Cycling (HATC) Test for Solder Reliability Assessment in BGA Packages

2007 ◽  
Author(s):  
X. Long ◽  
I. Dutta ◽  
R. Guduru ◽  
R. Prasanna ◽  
M. Pacheco
Keyword(s):  
Thermal Cycling ◽  
Solder Joints ◽  
Low Cycle Fatigue ◽  
Inelastic Strain ◽  
Fatigue Reliability ◽  
Element Analysis ◽  
Mechanical Cycling ◽  
Experimental Apparatus ◽  
Dependent Strain ◽  
Accelerated Thermal Cycling

A thermo-mechanical loading system, which can superimpose a temperature and location dependent strain on solder joints, is proposed in order to conduct highly accelerated thermal-mechanical cycling (HATC) tests to assess thermal fatigue reliability of Ball Grid Array (BGA) solder joints in microelectronics packages. The application of this temperature and position dependent strain produces generally similar loading modes (shear and tension) encountered by BGA solder joints during service, but substantially enhances the inelastic strain accumulated during thermal cycling over the same temperature range as conventional ATC (accelerated thermal cycling) tests, thereby leading to a substantial acceleration of low-cycle fatigue damage. Finite element analysis was conducted to aid the design of experimental apparatus and to predict the fatigue life of solder joints in HATC testing. Detailed analysis of the loading locations required to produce failure at the appropriate joint (next to the die-edge ball) under the appropriate tension/shear stress partition are presented. The simulations showed that the proposed HATC test constitutes a valid methodology for further accelerating conventional ATC tests. An experimental apparatus, capable of applying the requisite loads to a BGA package was constructed, and experiments were conducted under both HATC and ATC conditions. It is shown that HATC proffers much reduced cycling times compared to ATC.

Mechanisms of thermal cycling damage in polycrystalline Sn-rich solder joints

2020 ◽  
Vol 771 ◽  
pp. 138614 ◽  
Author(s):  
Marion Branch Kelly ◽  
Antony Kirubanandham ◽  
Nikhilesh Chawla
Keyword(s):  
Thermal Cycling ◽  
Solder Joints

scholarly journals Prediction of mechanical properties and fatigue life of nano silver paste in chip interconnection

2020 ◽  
Author(s):  
Hui YANG ◽  
Jihui Wu
Keyword(s):  
Fatigue Life ◽  
Solder Joint ◽  
Thermal Cycling ◽  
Solder Joints ◽  
Stress And Strain ◽  
Nano Silver ◽  
Finite Element Software ◽  
Flip Chips ◽  
Empirical Correction ◽  
Prediction Of Mechanical Properties

Abstract The simulation of nano-silver solder joints in flip-chips is performed by the finite element software ANSYS, and the stress-strain distribution results of the solder joints are displayed. In this simulation, the solder joints use Anand viscoplastic constitutive model, which can reasonably simulate the stress and strain of solder joints under thermal cycling load. At the same time this model has been embedded in ANSYS software, so it is more convenient to use. The final simulation results show that the areas where the maximum stresses and strains occur at the solder joints are mostly distributed in the contact areas between the solder joints and the copper pillars and at the solder joints. During the entire thermal cycling load process, the area where the maximum change in stress and strain occurs is always at the solder joint, and when the temperature changes, the temperature at the solder joint changes significantly. Based on comprehensive analysis, the relevant empirical correction calculation equation is used to calculate and predict the thermal fatigue life of nano-silver solder joints. The analysis results provide a reference for the application of nano-silver solder in the electronic packaging industry.

The failure models of Sn-based solder joints under coupling effects of electromigration and thermal cycling

2013 ◽  
Vol 113 (4) ◽  
pp. 044904 ◽  
Author(s):  
Limin Ma ◽  
Yong Zuo ◽  
Sihan Liu ◽  
Fu Guo ◽  
Xitao Wang
Keyword(s):  
Thermal Cycling ◽  
Solder Joints ◽  
Coupling Effects ◽  
Failure Models

Reliability of Fan-Out Wafer-Level Heterogeneous Integration

2018 ◽  
Vol 15 (4) ◽  
pp. 148-162 ◽  
Author(s):  
John Lau ◽  
Ming Li ◽  
Yang Lei ◽  
Margie Li ◽  
Iris Xu ◽  
...  
Keyword(s):  
Thermal Cycling ◽  
Printed Circuit Board ◽  
Solder Joints ◽  
Circuit Board ◽  
Heterogeneous Integration ◽  
Thermal Cycling Test ◽  
Wafer Level ◽  
Molding Compound ◽  
Shock Test ◽  
Cycling Test

Abstract In this study, the reliability (thermal cycling and shock) performances of a fan-out wafer-level system-in-package (SiP) or heterogeneous integration with one large chip (5 × 5 mm), three small chips (3 ×3 mm), and four capacitors (0402) embedded in an epoxy molding compound package (10 × 10 mm) with two redistribution layers (RDLs) are experimentally determined. Emphasis is placed on the estimation of the Weibull life distribution, characteristic life, and failure rate of the solder joint and RDL of this package. The fan-out wafer-level packaging is assembled on a printed circuit board (PCB) with more than 400 (Sn3wt%Ag0.5wt%Cu) solder joints. It is a six-layer PCB. The sample sizes for the thermal cycling test and shock test are, respectively, equal to 60 and 24. The failure location and modes of the thermal cycling test and shock test of the fan-out wafer-level SiP solder joints and RDLs are provided and discussed. 3-D nonlinear finite element models are also constructed and analyzed for the fan-out heterogeneous integration package during thermal cycling and shock conditions. The simulation results are correlated to the experimental results. Finally, recommendations on improving the fan-out wafer-level SiP solder joints and RDLs under thermal and shock conditions are provided.

The Future of Solder Joint Encapsulant

2015 ◽  
Vol 2015 (1) ◽  
pp. 000644-000648
Author(s):  
Mary Liu ◽  
Wusheng Yin
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Solder Joint ◽  
Thermal Cycling ◽  
Lower Cost ◽  
Solder Joints ◽  
Cost Of Ownership ◽  
The Future ◽  
High Temperature Solder

Solder joint encapsulant adhesives have been successfully used to enhance the strength of solder joints and improve thermal cycling as well as drop performance in finished products. The use of solder joint encapsulant adhesives can eliminate the need for underfill materials and the underfill process altogether, thus simplifying rework, which results in a lower cost of ownership. Solder joint encapsulant adhesives include: low temperature and high temperature solder joint encapsulant adhesives, and their derivatives. Each solder joint encapsulant adhesive has: unfilled and filled solder joint encapsulant adhesives, and solder joint encapsulant paste. Each solder joint encapsulant product has been designed for different applications. In this paper, we are going to discuss the details and future of solder joint encapsulant adhesives.

Reliability of Underfill-Encapsulated Flip-Chips With Heat Spreaders

1998 ◽  
Vol 120 (4) ◽  
pp. 322-327 ◽  
Author(s):  
H. Doi ◽  
K. Kawano ◽  
A. Yasukawa ◽  
T. Sato
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Thermal Cycling ◽  
Failure Mode ◽  
Flip Chip ◽  
Solder Joints ◽  
Alumina Substrate ◽  
Heat Spreader ◽  
Flip Chips ◽  
Heat Spreaders

The effect of a heat spreader on the life of the solder joints for underfill-encapsulated, flip-chip packages is investigated through stress analyses and thermal cycling tests. An underfill with suitable mechanical properties is found to be able to prolong the fatigue life of the solder joints even in a package with a heat spreader and an alumina substrate. The delamination of the underfill from the chip is revealed as another critical failure mode for which the shape of the underfill fillet has a large effect.

Sign in / Sign up

Export Citation Format

Share Document