Ultra Low power SRAM Cell for High Speed Applications using 90nm CMOS Technology

Author(s):  
Hansraj ◽  
Alka Chaudhary ◽  
Ajay Rana
2020 ◽  
Vol 12 (4) ◽  
pp. 04024-1-04024-4
Author(s):  
D. Berbara ◽  
◽  
M. Abboun Abid ◽  
M. Hebali ◽  
M. Benzohra ◽  
...  

2018 ◽  
Vol 7 (3.29) ◽  
pp. 70
Author(s):  
A S. S. Trinadh Kumar ◽  
B V. V. Satyanarayana

The usage of portable devices increasing rapidly in the modern life has led us to focus our attention to increase the performance of the SRAM circuits, especially for low power applications. Basically in six-Transistor (6T) SRAM cell either read or write operation can be performed at a time whereas, in 7T SRAM cell using single ended write operation and single ended read operation both write and read operations will be accomplished simultaneously at a time respectively. When it comes to operate in sub threshold region, single ended read operation will be degraded severely and single ended write operation will be severely degraded in terms of write-ability at lower voltages. To encounter these complications, an eight transistor SRAM cell is proposed. It performs single ended read operation and single ended write operation together even at sub threshold region down to 0.1V with improved read-ability using read assist and improved dynamic write-ability which helps in reducing the consumption of power by attaining a lower data retention voltage point. To reduce the total power consumption in the circuits, two extra access transistors are used in 8T SRAM cell which also helps in reducing the overall delay.  


Author(s):  
N. KUMAR BABU ◽  
P. SASIBALA

In this paper, we proposed two new structures for differential cascode voltage switch logic (DCVSL) pull-up stage. In conventional DCVSL structure these lies a drawback i.e. low-to-high propagation delay is larger than high-to-low propagation delay which could be reduced by using DCVSL-R. Using resistors in DCVSL-R structure, parasitic effects are coming into picture and it occupies more area on the chip [1]. To minimize these problems we propose a new Ultra Low Power Diode (ULPD) structures in place of resistors. This provides the minimum parasitic effects and occupies less area on the chip. Second one uses Complementary Pass Transistor Logic (CPTL) structure, which provides complementary outputs. This is an alternate circuit for conventional DCVSL structure. The performances of the proposed circuits are examined using cadence and model parameters of a 180nm CMOS process. This simulation result of the two circuits is presented and is compared. These circuits are suitable for VLSI implementation. Secondly, we proposed two new CMOS Schmitt trigger circuits. These Schmitt trigger circuits are evaluated both analytically and numerically with the sources from proposed ULPD ring oscillators. The hysteresis curves of the circuits are presented. The Schmitt triggers introduced here are most suitable for high speed applications. The proposed circuits havebeen designed in TSMC-0.18μm 1.8v CMOS technology and analyzed using spectre from cadence Design systems at 50MHz and 103MHz.


2021 ◽  
Vol 11 (1) ◽  
pp. 429
Author(s):  
Min-Su Kim ◽  
Youngoo Yang ◽  
Hyungmo Koo ◽  
Hansik Oh

To improve the performance of analog, RF, and digital integrated circuits, the cutting-edge advanced CMOS technology has been widely utilized. We successfully designed and implemented a high-speed and low-power serial-to-parallel (S2P) converter for 5G applications based on the 28 nm CMOS technology. It can update data easily and quickly using the proposed address allocation method. To verify the performances, an embedded system (NI-FPGA) for fast clock generation on the evaluation board level was also used. The proposed S2P converter circuit shows extremely low power consumption of 28.1 uW at 0.91 V with a core die area of 60 × 60 μm2 and operates successfully over a wide clock frequency range from 5 M to 40 MHz.


Sign in / Sign up

Export Citation Format

Share Document