Hydrothermal performance of plate-fin heat sinks for the cooling of portable and hand-held electronic devices

2019 ◽  
Author(s):  
Mohammed A. Boraey
Keyword(s):  
Electronic Devices ◽  
Heat Sinks

scholarly journals Cooling Performance of Heat Sinks Used in Electronic Devices

2018 ◽  
Vol 171 ◽  
pp. 02003
Author(s):  
Ibrahim Mjallal ◽  
Hussein Farhat ◽  
Mohammad Hammoud ◽  
Samer Ali ◽  
Ali AL Shaer ◽  
...  
Keyword(s):  
Heat Sink ◽  
Electronic Devices ◽  
Heat Fluxes ◽  
Electronic Cooling ◽  
Heat Sinks ◽  
Passive Cooling ◽  
Short Term ◽  
Cooling Systems ◽  
Thermal Output ◽  
Electrical Devices

Existing passive cooling solutions limit the short-term thermal output of systems, thereby either limiting instantaneous performance or requiring active cooling solutions. As the temperature of the electronic devices increases, their failure rate increases. That’s why electrical devices should be cooled. Conventional electronic cooling systems usually consist of a metal heat sink coupled to a fan. This paper compares the heat distribution on a heat sink relative to different heat fluxes produced by electronic chips. The benefit of adding a fan is also investigated when high levels of heat generation are expected.

Study on the Factors Influencing Spreading Resistance of Heat Sinks

2011 ◽  
Vol 301-303 ◽  
pp. 165-169
Author(s):  
Da Yong Gao ◽  
Jian Xin Zhang ◽  
Ping Juan Niu
Keyword(s):  
Heat Source ◽  
Heat Sink ◽  
Electronic Devices ◽  
Great Influence ◽  
Base Plate ◽  
Critical Value ◽  
Area Ratio ◽  
Heat Sinks ◽  
Spreading Resistance ◽  
Factors Influencing

The spreading resistance is a very important parameter in the applications of heat sink. The design of electronic devices will fail without considering the influence of the spreading resistance. In this paper, a simple thermal model was simulated by Computational Fluid Dynamics software. Some factors, which have great influence on the spreading resistance, have been analyzed. The spreading resistance decreases significantly with the increasing of the area ratio between the heat source and the base-plate. While the ratio being 1, the spreading resistance reaches the mix value. The greater the thermal conductivity of heat sink, the lower the spreading resistance. With the increasing of the thickness of base-plate, the spreading resistance reduces. However, if the thickness exceeds the critical value, the spreading resistance will increase. And the spreading resistance reaches the mix value while the centers of heat source and the base-plate are overlapped.

Performance Comparison of Microchannel Heat Sink Using Boron-Based Ceramic Materials

2021 ◽  
Vol 1163 ◽  
pp. 73-88
Author(s):  
Md Tanbir Sarowar
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Sink ◽  
Electronic Devices ◽  
Ceramic Materials ◽  
Substrate Material ◽  
Heat Sinks ◽  
Maximum Temperature ◽  
Microchannel Heat Sink ◽  
Small Surface

Microchannel heat sink plays a vital role in removing a considerable amount of heat flux from a small surface area from different electronic devices. In recent times, the rapid development of electronic devices requires the improvement of these heat sinks to a greater extent. In this aspect, the selection of appropriate substrate materials of the heat sinks is of vital importance. In this paper, three boron-based ultra-high temperature ceramic materials (ZrB2, TiB2, and HfB2) are compared as a substrate material for the microchannel heat sink using a numerical approach. The fluid flow and heat transfer are analyzed using the finite volume method. The results showed that the maximum temperature of the heat source didn’t exceed 355K at 3.6MWm-2 for any material. The results also indicated HfB2 and TiB2 to be more useful as a substrate material than ZrB2. By applying 3.6 MWm-2 heat flux at the source, the maximum obtained surface heat transfer coefficient was 175.2 KWm-2K-1 in a heat sink having substrate material HfB2.

The Role of Anodization in Naturally Cooled Heat Sinks for Power Electronic Devices

2020 ◽  
Vol 142 (5) ◽  
Author(s):  
Zhongchen Zhang ◽  
Michael Collins ◽  
Eric Lau ◽  
Chris Botting ◽  
Majid Bahrami
Keyword(s):  
Aluminum Alloy ◽  
Thermal Radiation ◽  
Electronic Devices ◽  
Heat Sinks ◽  
Al Alloy ◽  
Cast Aluminum Alloy ◽  
Power Electronic ◽  
Cast Aluminum ◽  
Die Cast ◽  
Alloy 6061

Abstract Effect of anodization on the thermal performance of naturally cooled heat sinks in power electronic devices made of die-cast aluminum alloy A380 and machined aluminum alloy 6061 was investigated experimentally and numerically. Various types of anodization were examined with different thickness of anodic aluminum oxide layer (AAO), pore size distributions, and surface coloring conditions. A customized natural convection and thermal radiation experimental chamber was built to measure the cooling capacity and heat sink temperatures. A 3D numerical model was also developed and validated against the collected data to provide more details into the contribution of the radiation heat transfer. The total emittance of the anodized samples was determined by a Fourier transform infrared reflectometer (FTIR) spectroscopy method. The results show a significant improvement in total hemispherical emissivity from 0.14 to 0.92 in anodized die-cast aluminum samples. This increase resulted in a considerable reduction in overall thermal resistance, up to 15%; where up to 41% of the total heat dissipation was contributed by thermal radiation. In spite of the rather distinguishable surface morphologies, the measurements suggested that thermal emissivity of the anodized die-cast Al A380 and Al alloy 6061 samples were in the same range.

Thermal Analysis of Miniature Low Profile Heat Sinks With and Without Fins

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
V. Egan ◽  
P. A. Walsh ◽  
E. Walsh ◽  
R. Grimes
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Volume Flow Rate ◽  
Electronic Devices ◽  
Heat Fluxes ◽  
Heat Sinks ◽  
Superior Performance ◽  
Low Profile ◽  
In Series ◽  
Heat Sink Design

Reliable and efficient cooling solutions for portable electronic devices are now at the forefront of research due to consumer demand for manufacturers to downscale existing technologies. To achieve this, the power consumed has to be dissipated over smaller areas resulting in elevated heat fluxes. With regard to cooling such devices, the most popular choice is to integrate a fan driven heat sink, which for portable electronic devices must have a low profile. This paper presents an experimental investigation into such low profile cooling solutions, which incorporate one of the smallest commercially available fans in series with two different heat sink designs. The first of these is the conventionally used finned heat sink design, which was specifically optimized and custom manufactured in the current study to complement the driving fan. While the second design proposed is a novel “finless” type heat sink suitable for use in low profile applications. Together the driving fan and heat sinks combined were constrained to have a total footprint area of 465 mm2 and a profile height of only 5 mm, making them ideal for use in portable electronics. The objective was to evaluate the performance of the proposed finless heat sink design against a conventional finned heat sink, and this was achieved by means of thermal resistance and overall heat transfer coefficient measurements. It was found that the proposed finless design proved to be the superior cooling solution when operating at low fan speeds, while at the maximum fan speed tested of 8000 rpm both provided similar performance. Particle image velocimetry measurements were used to detail the flow structures within each heat sink and highlighted methods, which could further optimize their performance. Also, these measurements along with corresponding global volume flow rate measurements were used to elucidate the enhanced heat transfer characteristics observed for the finless design. Overall, it is shown that the proposed finless type heat sink can provide superior performance compared with conventional finned designs when used in low profile applications. In addition a number of secondary benefits associated with such a design are highlighted including lower cost, lower mass, lower acoustics, and reduced fouling issues.

Computational fluid dynamics for thermal performance of a water-cooled minichannel heat sink with different chip arrangements

2014 ◽  
Vol 24 (4) ◽  
pp. 797-810 ◽  
Author(s):  
Gongnan Xie ◽  
Shian Li ◽  
Bengt Sunden ◽  
Weihong Zhang
Keyword(s):  
Heat Transfer ◽  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Thermal Performance ◽  
Heat Sink ◽  
Electronic Devices ◽  
Heat Sinks ◽  
Bottom Surface ◽  
Moderate Pressure ◽  
Content Type

Purpose – With the development of electronic devices, including the desires of integration, miniaturization, high performance and the output power, cooling requirement of chips have been increased gradually. Water-cooled minichannel is an effective cooling technology for cooling of heat sinks. The minichannel flow geometry offers large surface area for heat transfer and a high convective heat transfer coefficient with only a moderate pressure loss. The purpose of this paper is to analyze a minichannel heat sink having the bottom size of 35 mm×35 mm numerically. Two kinds of chip arrangement are investigated: diagonal arrangement and parallel arrangement. Design/methodology/approach – Computational fluid dynamics (CFD) technique is used to investigate the flow and thermal fields in forced convection in a three-dimensional minichannels heat sink with different chip arrangements. The standard k-e turbulence model is applied for the turbulence simulations on the minichannel heat sink. Findings – The results show that the bottom surface of the heat sink with various chip arrangements will have different temperature distribution and thermal resistance. A suitable chip arrangement will achieve a good cooling performance for electronic devices. Research limitations/implications – The fluid is incompressible and the thermophysical properties are constant. Practical implications – New and additional data will be helpful as guidelines in the design of heat sinks to achieve a good thermal performance and a long lifetime in operation. Originality/value – In real engineering situations, chips are always placed in various manners according to design conditions and constraints. In this case the assumption of uniform heat flux is acceptable for the surfaces of the chips rather than for the entire bottom surface of the heat sink.

Improved Heat Dissipation Capability on Electronic Motor Control Devices

2005 ◽  
Author(s):  
Wei Tong
Keyword(s):  
Heat Transfer ◽  
Motor Control ◽  
Heat Dissipation ◽  
Electronic Devices ◽  
Heat Sinks ◽  
Vortex Generators ◽  
Maximum Temperature ◽  
Complex Heat Transfer ◽  
Pin Fins ◽  
Control Devices

Heat sinks have been widely used in electronic industry to maintain the operation temperatures of electronic devices lower than their allowable values and thus are often critical to the device performance and life. However, it is difficult to design heat sinks to satisfy all design specifications optimally under complex heat transfer phenomena. The present work discloses a new design of heat sinks to improve heat dissipation capability for electric motor control devices. The heat sink contains a plurality of raindrop-shaped pin fins, acting as vortex generators to increase the rate of heat transfer and in turn, to increase the cooling efficiency of the heat sinks. Numerical results have shown that with the new designed heat sinks, the maximum temperature can reduce about 30% over the conventional heat sinks.

Thermally Conductive Plastics for Enhanced Thermal Management

2015 ◽  
Vol 2015 (1) ◽  
pp. 000530-000535
Author(s):  
Chandrashekar Raman
Keyword(s):  
Thermal Conductivity ◽  
Natural Convection ◽  
Thermal Management ◽  
Electronic Devices ◽  
Heat Sinks ◽  
Significant Challenge ◽  
Design Engineers ◽  
Thermally Conductive ◽  
New Material ◽  
Conductive Plastics

Electronic devices continue to shrink while continuing to offer increasing functionality. This trend poses a significant challenge to design engineers who need to adequately address the increasing thermal management requirements of these devices on a shrinking footprint. Thermally conductive plastics have been gaining attention as an innovative new material option to address this challenge. While plastics are typically poor conductors of heat, it is possible to increase the thermal conductivity with the use of certain additives. Unique ceramic additives like boron nitride offer the added advantage of enabling thermally conductive plastic formulations that are also electrically insulating. The replacement of aluminum heat sinks in free (natural) convection environments with thermally conductive plastics is discussed in this paper. The results show it may indeed be possible to replace aluminum with thermally conductive plastic heat sinks in convection limited environments, and if judicious redesign of the plastic heat sink is incorporated, an improved thermal management solution can be realized. Additionally, the benefits of enhancing existing plastic housings to enable an improved thermal management solution are discussed. The results also show that modest enhancements to the thermal conductivity of existing plastic housings can yield significant improvements to the overall thermal management solution as well.

Enhanced Thermal Performance of Internal Y-Shaped Bifurcation Microchannel Heat Sinks With Metal Foams

2017 ◽  
Vol 10 (1) ◽  
Author(s):  
Han Shen ◽  
Xueting Liu ◽  
Hongbin Yan ◽  
Gongnan Xie ◽  
Bengt Sunden
Keyword(s):  
Thermal Management ◽  
Thermal Performance ◽  
Metal Foam ◽  
Electronic Devices ◽  
Metal Foams ◽  
Heat Sinks ◽  
High Power Density ◽  
Pore Density ◽  
Transfer Enhancement ◽  
Microchannel Heat Sinks

Internal Y-shaped bifurcation has been proved to be an advantageous way on improving thermal performance of microchannel heat sinks according to the previous research. Metal foams are known due to their predominate performance such as low-density, large surface area, and high thermal conductivity. In this paper, different parameters of metal foams in Y-shaped bifurcation microchannel heat sinks are designed and investigated numerically. The effects of Reynolds number, porosity of metal foam, and the pore density (PPI) of the metal foam on the microchannel heat sinks are analyzed in detail. It is found that the internal Y-shaped bifurcation microchannel heat sinks with metal foam exhibit better heat transfer enhancement and overall thermal performance. This research provides broad application prospects for heat sinks with metal foam in the thermal management of high power density electronic devices.

scholarly journals A parametric investigation of a PCM-based pin fin heat sink

2015 ◽  
Vol 6 (1) ◽  
pp. 65-73 ◽  
Author(s):  
R. Pakrouh ◽  
M. J. Hosseini ◽  
A. A. Ranjbar
Keyword(s):  
Heat Sink ◽  
Phase Change Materials ◽  
Electronic Devices ◽  
Operating Time ◽  
Heat Sinks ◽  
Geometrical Parameters ◽  
Base Temperature ◽  
Pin Fin ◽  
Heat Transfer Calculation ◽  
Acceptable Agreement

Abstract. This paper presents a numerical investigation in which thermal performance characteristics of pin fin heat sinks enhanced with phase-change materials (PCMs) designed for cooling of electronic devices are studied. The paraffin RT44 HC is poured into the aluminum pin fin heat sink container, which is chosen for its high thermal conductivity. The effects of different geometrical parameters, including number, thickness and height of fins, on performance are analyzed. Different aspects for heat transfer calculation, including the volume expansion in phase transition as well as natural convection in a fluid zone, are considered in the study. In order to validate the numerical model, previous experimental data and the present results are compared, and an acceptable agreement between these two is observed. Results show that increasing the number, thickness and height of fins leads to a significant decrease in the base temperature as well as operating time of the heat sink.

Sign in / Sign up

Export Citation Format

Share Document