Design of Coplanar Waveguide On-Chip Impedance-Matching Circuit for Wireless Receiver Front-End

Author(s):  
H. Kanaya ◽  
R.K. Pokharel ◽  
F. Koga ◽  
Z. Arima ◽  
S. Kim ◽  
...  
2007 ◽  
Vol 4 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Qing Liu ◽  
Patrick Fay ◽  
Gary H. Bernstein

Quilt Packaging (QP), a novel chip-to-chip communication paradigm for system-in-package integration, is presented. By forming protruding metal nodules along the edges of the chips and interconnecting integrated circuits (ICs) through them, QP offers an approach to ameliorate the I/O speed bottleneck. A fabrication process that includes deep reactive ion etching, electroplating, and chemical-mechanical polishing is demonstrated. As a low-temperature process, it can be easily integrated into a standard IC fabrication process. Three-dimensional electromagnetic simulations of coplanar waveguide QP structures have been performed, and geometries intended to improve impedance matching at the interface between the on-chip interconnects and the chip-to-chip nodule structures were evaluated. Test chips with 100 μm wide nodules were fabricated on silicon substrates, and s-parameters of chip-to-chip interconnects were measured. The insertion loss of the chip-to-chip interconnects was as low as 0.2 dB at 40 GHz. Simulations of 20 μm wide QP structures suggest that the bandwidth of the inter-chip nodules is expected to be above 200 GHz.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Mohammad Alibakhshikenari ◽  
Bal S. Virdee ◽  
Leyre Azpilicueta ◽  
Chan H. See ◽  
Raed Abd-Alhameed ◽  
...  

AbstractMatching the antenna’s impedance to the RF-front-end of a wireless communications system is challenging as the impedance varies with its surround environment. Autonomously matching the antenna to the RF-front-end is therefore essential to optimize power transfer and thereby maintain the antenna’s radiation efficiency. This paper presents a theoretical technique for automatically tuning an LC impedance matching network that compensates antenna mismatch presented to the RF-front-end. The proposed technique converges to a matching point without the need of complex mathematical modelling of the system comprising of non-linear control elements. Digital circuitry is used to implement the required matching circuit. Reliable convergence is achieved within the tuning range of the LC-network using control-loops that can independently control the LC impedance. An algorithm based on the proposed technique was used to verify its effectiveness with various antenna loads. Mismatch error of the technique is less than 0.2%. The technique enables speedy convergence (< 5 µs) and is highly accurate for autonomous adaptive antenna matching networks.


2021 ◽  
Vol 11 (2) ◽  
pp. 22
Author(s):  
Umberto Ferlito ◽  
Alfio Dario Grasso ◽  
Michele Vaiana ◽  
Giuseppe Bruno

Charge-Based Capacitance Measurement (CBCM) technique is a simple but effective technique for measuring capacitance values down to the attofarad level. However, when adopted for fully on-chip implementation, this technique suffers output offset caused by mismatches and process variations. This paper introduces a novel method that compensates the offset of a fully integrated differential CBCM electronic front-end. After a detailed theoretical analysis of the differential CBCM topology, we present and discuss a modified architecture that compensates mismatches and increases robustness against mismatches and process variations. The proposed circuit has been simulated using a standard 130-nm technology and shows a sensitivity of 1.3 mV/aF and a 20× reduction of the standard deviation of the differential output voltage as compared to the traditional solution.


Sensors ◽  
2021 ◽  
Vol 21 (9) ◽  
pp. 2916
Author(s):  
Junho Yeo ◽  
Jong-Ig Lee

A miniaturized wideband loop antenna for terrestrial digital television (DTV) and ultra-high definition (UHD) TV applications is proposed. The original wideband loop antenna consists of a square loop, two circular sectors to connect the loop with central feed points, and a 75 ohm coplanar waveguide (CPW) feed line inserted in the lower circular sector. The straight side of the square loop is replaced with a multiple half-circular-ring-based loop structure. Horizontal slits are appended to the two circular sectors in order to further reduce the antenna size. A tapered CPW feed line is also employed in order to improve impedance matching. The experiment results show that the proposed miniaturized loop antenna operates in the 460.7–806.2 MHz frequency band for a voltage standing wave ratio less than two, which fully covers the DTV and UHD TV bands (470–771 MHz). The proposed miniaturized wideband loop antenna has a length reduction of 21.43%, compared to the original loop antenna.


2016 ◽  
Vol 184 (1-2) ◽  
pp. 412-417 ◽  
Author(s):  
A. Endo ◽  
S. J. C. Yates ◽  
J. Bueno ◽  
D. J. Thoen ◽  
V. Murugesan ◽  
...  

2013 ◽  
Vol 6 (2) ◽  
pp. 167-172 ◽  
Author(s):  
Srinivasan Ashok Kumar ◽  
Thangavelu Shanmuganantham

A novel coplanar waveguide fed Industrial, Scientific, and Medical (ISM) band implantable crossed-type triangular slot antenna is proposed for biomedical applications. The antenna operates at the center frequency of 2450 MHz, which is in ISM band, to support GHz wideband communication for high-data rate implantable biomedical application. The size of the antenna is 78 mm3 (10 mm × 12 mm × 0.65 mm). The simulated and measured bandwidths are 7.9 and 8.2% at the resonant frequency of 2.45 GHz. The specific absorption rate distribution induced by the implantable antenna inside a human body tissue model is evaluated. The communication between the implanted antenna and external device is also examined. The proposed antenna has substantial merits such as miniaturization, lower return loss, better impedance matching, and high gain over other implanted antennas.


2017 ◽  
Vol 25 (26) ◽  
pp. 32919 ◽  
Author(s):  
Hyunho Jung ◽  
Myungjae Lee ◽  
Changhyun Han ◽  
Yeonsang Park ◽  
Kyung-Sang Cho ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document