Evaluation of Flow Behavior for Clearance Brush Seals

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
Yahya Dogu ◽  
Mahmut F. Aksit ◽  
Mehmet Demiroglu ◽  
Osman Saim Dinc
Keyword(s):  
Flow Field ◽  
Flow Behavior ◽  
Industrial Applications ◽  
Operating Conditions ◽  
Brush Seal ◽  
Sealing Performance ◽  
Computational Fluid Dynamics Analysis ◽  
Flow Features ◽  
Brush Seals ◽  
Initial Clearance

The industrial applications of brush seals have been increasing due to their superior sealing performance. Advances in the understanding of seal behavior have been pushing the design limits to higher-pressure load, temperature, surface speed, and rotor excursion levels. The highest sealing performance can be achieved when the bristle pack maintains contact with the rotor surface. However, due to many design and operational constraints, most seals operate with some clearance. This operating clearance cannot be avoided due to rotor runouts, transient operating conditions, or excessive bristle wear. In some applications, a minimum initial clearance is required to ensure a certain amount of flow rate for component cooling or purge flow. Typically, brush seal failure occurs in the form of degraded sealing performance due to increasing seal clearance. The seal performance is mainly characterized by the flow field in close vicinity of the bristle pack, through the seal-rotor clearance, and within the bristle pack. This work investigates the flow field for a brush seal operating with some bristle-rotor clearance. A nonlinear form of the momentum transport equation for a porous medium of the bristle pack has been solved by employing the computational fluid dynamics analysis. The results are compared with prior experimental data. The flow field for the clearance seal is observed to have different characteristics compared to that for the contact seal. Outlined as well are the flow features influencing the bristle dynamics.

Fundamental Design Issues of Brush Seals for Industrial Applications

2002 ◽  
Vol 124 (2) ◽  
pp. 293-300 ◽  
Author(s):  
Saim Dinc ◽  
Mehmet Demiroglu ◽  
Norman Turnquist ◽  
Jason Mortzheim ◽  
Gayle Goetze ◽  
...  
Keyword(s):  
High Speed ◽  
Failure Modes ◽  
Industrial Applications ◽  
Operating Conditions ◽  
Design Parameters ◽  
Design Criteria ◽  
Seal Design ◽  
Brush Seal ◽  
Brush Seals ◽  
As Stress

Advanced seals have been applied to numerous turbine machines over the last decade to improve the performance and output. Industrial experiences have shown that significant benefits can be attained if the seals are designed and applied properly. On the other hand, penalties can be expected if brush seals are not designed correctly. In recent years, attempts have been made to apply brush seals to more challenging locations with high speed (>400 m/s), high temperature (>650 °C), and discontinuous contact surfaces, such as blade tips in a turbine. Various failure modes of a brush seal can be activated under these conditions. It becomes crucial to understand the physical behavior of a brush seal under the operating conditions, and to be capable of quantifying seal life and performance as functions of both operating parameters and seal design parameters. Design criteria are required for different failure modes such as stress, fatigue, creep, wear, oxidation etc. This paper illustrates some of the most important brush seal design criteria and the trade-off of different design approaches.

Influence of Geometry on Rotordynamic Coefficients of Brush Seal

2017 ◽  
Vol 34 (2) ◽  
Author(s):  
Yuan Wei ◽  
Earl H. Dowell ◽  
Zhaobo Chen ◽  
Yinghou Jiao ◽  
Zhouqiang Zhang
Keyword(s):  
Aerodynamic Force ◽  
Dynamic Pressure ◽  
Reaction Force ◽  
Operating Conditions ◽  
Rotordynamic Coefficients ◽  
Geometric Configurations ◽  
Brush Seal ◽  
Sealing Performance ◽  
Flow Features ◽  
The Relationship

AbstractIt has been observed that the geometry of a brush seal has a significant effect on the sealing performance. However, the relationship between rotordynamic coefficients and geometry factors of the brush seal itself are rarely considered. In this article, the rotordynamic coefficients of a typical single-stage brush seal for different geometries and operating conditions were numerically analyzed using CFD RANS solutions coupled with a non-Darcian porous medium model. The reaction force which plays an essential role in rotordynamic coefficients was obtained by integrating the dynamic pressure distribution. The influence of the bristle pack thickness, fence height, clearance size and other working condition parameters on aerodynamic force, stiffness coefficients, and damping coefficients of brush seal were presented and compared. In addition, the effects of various geometric configurations on pressure and flow features were also discussed.

Fundamental Design Issues of Brush Seals for Industrial Applications

2001 ◽  
Author(s):  
Saim Dinc ◽  
Mehmet Demiroglu ◽  
Norman Turnquist ◽  
Jason Mortzheim ◽  
Gayle Goetze ◽  
...  
Keyword(s):  
High Speed ◽  
Failure Modes ◽  
Industrial Applications ◽  
Operating Conditions ◽  
Design Parameters ◽  
Design Criteria ◽  
Seal Design ◽  
Brush Seal ◽  
Brush Seals ◽  
As Stress

Advanced seals have been applied to numerous turbine machines over the last decade to improve the performance and output. Industrial experiences have shown that significant benefits can be attained if the seals are designed and applied properly. On the other hand, penalties can be expected if brush seals are not designed correctly. In recent years, attempts have been made to apply brush seals to more challenging locations with high speed (>400 m/s), high temperature (>650 °C), and discontinuous contact surfaces, such as blade tips in a turbine. Various failure modes of a brush seal can be activated under these conditions. It becomes crucial to understand the physical behavior of a brush seal under the operating conditions, and to be capable of quantifying seal life and performance as functions of both operating parameters and seal design parameters. Design criteria are required for different failure modes such as stress, fatigue, creep, wear, oxidation etc. This paper illustrates some of the most important brush seal design criteria and the trade-off of different design approaches.

Investigation of Brush Seal Flow Characteristics Using Bulk Porous Medium Approach

2005 ◽  
Vol 127 (1) ◽  
pp. 136-144 ◽  
Author(s):  
Yahya Dogu
Keyword(s):  
Porous Medium ◽  
Flow Behavior ◽  
Flow Analysis ◽  
Operating Conditions ◽  
Force Balance ◽  
Complex Flow ◽  
Blow Down ◽  
Permeability Coefficients ◽  
Backing Plate ◽  
Brush Seal

The flow behavior through a brush seal has been investigated by developing a flow analysis procedure with a porous medium approach. In order to increase the brush seal performance and use at more severe operating conditions, the complex flow in the bristle pack has become the major concern affecting seal features such as blow-down, hang-up, hysteresis, and bristle flutter. In this study, an axisymmetric CFD model is employed to calibrate anisotropic permeability coefficients for the bristle pack based on available experimental data: leakage, axial pressure on the rotor surface, and radial pressure on the backing plate. A simplified form of the force balance equation is introduced for the flow in the porous bristle pack. Different sets of permeability coefficients are defined for the fence height region below the seal backing plate and the upper region of the seal to correlate the different physical structures and behavior of these regions during operation. The upper region is subject to more stiffening due to backing plate support while the fence height region is free to spread and bend in the axial direction. It is found that flow resistance for the upper region should be 20% higher than the fence height region in order to match the experimental pressure within the bristle pack. Analysis results prove that the brush seal is well represented as a porous medium with this approach. Based on the model developed, characteristic flow and pressure fields in the entire bristle pack have been explored.

Breaking the Swirl With Brush Seals: Numerical Modeling and Experimental Evidence

2008 ◽  
Author(s):  
Peter Helm ◽  
Alexander Pugachev ◽  
Matthias Neef
Keyword(s):  
Experimental Evidence ◽  
Swirl Flow ◽  
Operating Conditions ◽  
Brush Seal ◽  
Stable Operating ◽  
Beneficial Impact ◽  
Rotor Surface ◽  
Brush Seals ◽  
Experimental Values ◽  
The Impact

Striving for smaller losses in turbomachinery has led to many advancements in the design of seals. Modern sealing concepts such as brush seals hold a great potential to increase the efficiency of both flight engines and stationary turbines. At the same time, in order to maintain stable operating conditions of the rotor, swirl-induced forces must be kept at a minimum in the sealing channels. Therefore, the influence of the permeable and flexible bristle pack of brush seals on the flow around the rotor surface must be known. In this paper the swirl flow in the cavities of two different seal geometries is studied experimentally and numerically. A conventional three-tooth labyrinth serves as a reference. A second seal arrangement with a bristle pack upstream of two teeth is compared with the reference labyrinth. The swirl is evaluated experimentally from total and static pressure measurements in various axial and circumferential positions. Additionally, the axial swirl distribution is calculated using computational fluid dynamics (CFD). Here, the numerical model of the brush seal is based on the porous medium approach and is calibrated using the experimental values of the leakage and the bristle clearance by adjusting the thickness of the bristle pack. The calibrated CFD model is then used to study the impact of the brush seal on the swirl component of the sealing flow. The observed significant decrease of the swirl by the brush seal shows good agreement with the experimental data. The impact of changes in bristle pack clearance on the swirl is also investigated and compared with experimental evidence. The aim is to show that the brush seals have a natural tendency to interrupt seal swirl. They can therefore be used for swirl control in order to create a beneficial impact on the dynamic stability of turbomachines.

CFD Simulation of a Supersonic Steam Ejector for Refrigeration Application

2016 ◽  
Author(s):  
Liju Su ◽  
Ramesh K. Agarwal
Keyword(s):  
Flow Field ◽  
Cfd Simulation ◽  
Fluid Pressure ◽  
Turbulence Models ◽  
Industrial Applications ◽  
Operating Conditions ◽  
Working Fluid ◽  
Entrainment Ratio ◽  
Ansys Fluent ◽  
Entrainment Velocity

Supersonic steam ejectors are widely used in many industrial applications, for example for refrigeration and desalination. The experimental evaluation of the flow field inside the ejector is relatively difficult and costly due to the occurrence of shock after the velocity of the steam reaches over the sonic level in the ejector. In this paper, numerical simulations are conducted to investigate the detailed flow field inside a supersonic steam (water vapor being the working fluid) ejector. The commercial computational fluid dynamics (CFD) flow solver ANSYS-Fluent and the mesh generation software ANSYS-ICEM are used to predict the steam performance during the mixing inside the ejector by employing two turbulence models, the k-ω SST and the k-ε realizable models. The computed results are validated against the experimental data. The effects of operating conditions on the efficiency of the ejector such as the primary fluid pressure and condenser pressure are studied to obtain a better understanding of the mixing process and entrainment. Velocity contours, pressure plots and shock region analyses provide a good understanding for optimization of the ejector performance, in particular how to increase the entrainment ratio.

Influence of Lubrication Oil on the Performance of Carbon Fibre Brush Seals for Aero-Engines Bearing Chambers

2019 ◽  
Author(s):  
Bilal Outirba ◽  
Patrick Hendrick
Keyword(s):  
Carbon Fibre ◽  
Rotational Speed ◽  
Fibre Length ◽  
Operating Conditions ◽  
Geometrical Parameters ◽  
Labyrinth Seals ◽  
Brush Seal ◽  
Lubrication Oil ◽  
Brush Seals ◽  
Aero Engines

Abstract Carbon fibre brush seals are an alternative to labyrinth seals in aero-engines lubrication systems due to better sealing ability with low power loss. However, the use of brush seals still raises concerns about coking issues. In addition, the influence of oil on the brush seal behaviour needs to be fully assessed. This paper provides an experimental investigation of the effect of lubrication oil on the performance of carbon fibre brush seals under static and dynamic conditions. Eight brush seal samples of various geometrical designs were submitted to an environment recreating the working conditions of a modern aero-engine bearing chamber in terms of rotational speed, air pressure, and oil type of injection and temperature. The test results indicated that the performance of carbon fibre brush seals was deeply influenced by the presence of oil within fibres. Oil deeply influences leakage performance, depending on geometrical parameters (density, fibre length and interference) and operating conditions (oil temperature, rotational speed). Brush seal fibre pack is mainly prone to hydrodynamic lift and oil soaking, which is defined by the ability of lubrication oil to fill in properly the interstices between fibres. Viscosity and surface tension may be the key properties influencing oil soaking. Seal torque data corroborates the presence of a hydrodynamic lift. In addition, in absence of differential pressure, seal torque decrease with when oil temperature increases indicates the existence of a critical viscosity. Finally, oil lubrication within the bristles allows reduction of the inter-bristle friction, thus limiting hysteresis.

scholarly journals Computational fluid dynamics analysis of the influence of injection nozzle lateral outflow on the performance of Ranque-Hilsch vortex tube

2014 ◽  
Vol 18 (4) ◽  
pp. 1191-1201 ◽  
Author(s):  
Nader Pourmahmoud ◽  
Alireza Izadi ◽  
Amir Hassanzadeh ◽  
Ashkan Jahangiramini
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Field ◽  
Vortex Tube ◽  
Operating Conditions ◽  
Energy Separation ◽  
Physical Parameters ◽  
Dynamics Analysis ◽  
Computational Domain ◽  
Computational Fluid Dynamics Analysis

In this article computational fluid dynamics analysis of a three-dimensional compressible and turbulent flow has been carried out through a vortex tube. The standard k-? turbulence model is utilized in order to simulate an axisymmetric computational domain. The numerical simulation has focused on the energy separation and flow field patterns of a somewhat nonconventional vortex tube, which is on the basis of creating an external hole at the end of each nozzle. According to the selected nozzles geometry, some of unfavorable phenomena such as shock wave, high pressure regions and appearing of unsymmetrical rotating flow patterns in the vortex chamber would be recovered significantly. In this way the physical parameters of flow field are derived under different both inlet mass flow rates and outlet pressures of nozzles hole (OPH). The results show that increasing OPH value enhanced the cooling capacity of machine in the most of operating conditions.

Transient Temperature Measurements in the Contact Zone Between Brush Seals of Kevlar and Metallic Type for Bearing Chamber Sealing Using a Pyrometric Technique

2013 ◽  
Vol 135 (8) ◽  
Author(s):  
Michael Flouros ◽  
Martin Stadlbauer ◽  
Francois Cottier ◽  
Stephan Proestler ◽  
Stefan Beichl
Keyword(s):  
Contact Zone ◽  
Operating Conditions ◽  
Temperature Measurements ◽  
Transient Temperature ◽  
Labyrinth Seals ◽  
Brush Seal ◽  
Aero Engine ◽  
Rotating Surface ◽  
Brush Seals ◽  
Engine Bearing

For the past 25 years brush seal technologies have evolved into the aero engine designs and, more generally, into the gas turbine world, not only for sealing gas areas at different pressure levels but also for sealing gas/liquid environments. This is the case in an aero engine where the bearing chambers are sealed. Aero engine bearing chambers enclose oil lubricated components such bearings and gears. In order to avoid contamination of the turbo machinery through oil loss, air blown seals are used to retain the oil into the bearing chamber. Oil loss may cause coking or ignition with the probability of an uncontained destruction of rotating parts such as disks or blades. It may also cause contamination of the air conditioning system with oil fumes thus causing health problems to the passengers and crew from such exposure. The most widely known seals for bearing chamber sealing are the labyrinth seals, however, in recent years brush seals and carbon seals have also been used. The latter are contact seals; that is, they may be installed having zero clearance to the rotating part and lift during operation when their air side is pressurized. During this survey an actual aero engine bearing chamber was modified to run with brush seals in a simulating rig. Two types of brush seals were used: (a) with bristles made of Kevlar, and (b) bristles made of a metallic material. Both types were installed with an overlap to the rotor. The targets set were twofold: (a) to measure the transient temperatures in the rotor and particularly in the contact zone between the bristles and the rotor, and (b) to measure the air leakage through the seals at different operating conditions. In order to obtain the transient temperature measurements with high fidelity, a new pyrometric technique was developed and was applied for the first time in brush seals. This technique has enabled placement of the pyrometer into the bristle's pack of the seal adjacent to the rotating surface and it could record the frictional temperature evolution in the bristles/rotor contact zone during acceleration or deceleration of the rotor. Additionally, the air consumption of the seals was measured and was compared to the air consumption through the labyrinth seals. For the metallic brush seal, up to 80% of the required sealing air can be saved, which can result, in turn, into a reduction in fuel burned by up to 1%. Furthermore, a design simplification of the bearing chamber architecture can be achieved by taking into account the reduced air flow. Even though the rotor was accelerated to high speeds up to 19,500 rpm, the produced temperature overshoots in the seal/rotor contact zone have caused no deterioration in either the materials or the oil.

Computational Fluid Dynamics Investigation of Brush Seal Leakage Performance Depending on Geometric Dimensions and Operating Conditions

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
Yahya Dogu ◽  
Ahmet S. Bahar ◽  
Mustafa C. Sertçakan ◽  
Altuğ Pişkin ◽  
Ercan Arıcan ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Pressure Ratio ◽  
Plate Thickness ◽  
Operating Conditions ◽  
Design Parameters ◽  
Backing Plate ◽  
Brush Seal ◽  
Front Plate ◽  
Brush Seals

Brush seals require custom design and tailoring due to their behavior driven by flow dynamic, which has many interacting design parameters, as well as their location in challenging regions of turbomachinery. Therefore, brush seal technology has not reached a conventional level across the board standard. However, brush seal geometry generally has a somewhat consistent form. Since this consistent form does exist, knowledge of the leakage performance of brush seals depending on specific geometric dimensions and operating conditions is critical and predictable information in the design phase. However, even though there are common facts for some geometric dimensions available to designers, open literature has inadequate quantified information about the effect of brush seal geometric dimensions on leakage. This paper presents a detailed computational fluid dynamics (CFD) investigation quantifying the leakage values for some geometric variables of common brush seal forms functioning in some operating conditions. Analyzed parameters are grouped as follows: axial dimensions, radial dimensions, and operating conditions. The axial dimensions and their ranges are front plate thickness (z1 = 0.040–0.150 in.), distance between front plate and bristle pack (z2 = 0.010–0.050 in.), bristle pack thickness (z3 = 0.020–0.100 in.), and backing plate thickness (z4 = 0.040–0.150 in.). The radial dimensions are backing plate fence height (r1 = 0.020–0.100 in.), front plate fence height (r2 = 0.060–0.400 in.), and bristle free height (r3 = 0.300–0.500 in.). The operating conditions are chosen as clearance (r0 = 0.000–0.020 in.), pressure ratio (Rp = 1.5–3.5), and rotor speed (n = 0–40 krpm). CFD analysis was carried out by employing compressible turbulent flow in 2D axisymmetric coordinate system. The bristle pack was treated as a porous medium for which flow resistance coefficients were calibrated by using literature based test data. Selected dimensional and operational parameters for a common brush seal form were investigated, and their effects on leakage performance were quantified. CFD results show that, in terms of leakage, the dominant geometric dimensions were found to be the bristle pack thickness and the backing plate fence height. It is also clear that physical clearance dominates leakage performance, when compared to the effects of other geometric dimensions. The effects of other parameters on brush seal leakage were also analyzed in a comparative manner.

Sign in / Sign up

Export Citation Format

Share Document