Low-Dimensional Sagittal Plane Model of Normal Human Walking

2008 ◽  
Vol 130 (5) ◽  
Author(s):  
S. Srinivasan ◽  
I. A. Raptis ◽  
E. R. Westervelt

This paper applies a robotics-inspired approach to derive a low-dimensional forward-dynamic hybrid model of human walking in the sagittal plane. The low-dimensional model is derived as a subdynamic of a higher-dimensional anthropomorphic hybrid model. The hybrid model is composed of models for single support (SS) and double support (DS), with the transition from SS to DS modeled by a rigid impact to account for the impact at heel-contact. The transition from DS to SS occurs in a continuous manner. Existing gait data are used to specify, via parametrization, the low-dimensional model that is developed. The primary result is a one-degree-of-freedom model that is an exact subdynamic of the higher-dimensional anthropomorphic model and describes the dynamics of walking. The stability properties of the model are evaluated using the method of Poincaré. The low-dimensional model is validated using the measured human gait data. The validation demonstrates the observed stability of the measured gait.

Author(s):  
Justin Seipel

The objective of work presented in this paper is to increase the center-of-mass stability of human walking and running in musculo-skeletal simulation. The approach taken is to approximate the whole-body dynamics of the low-dimensional Spring-Loaded Inverted Pendulum (SLIP) model of locomotion in the OpenSim environment using existing OpenSim tools. To more directly relate low-dimensional dynamic models to human simulation, an existing OpenSim human model is first modified to more closely represent bilateral above-knee amputee locomotion with passive prostheses. To increase stability further beyond the energy-conserving SLIP model, an OpenSim model based upon the Clock-Torqued Spring-Loaded-Inverted-Pendulum (CT-SLIP) model of locomotion is also created. The result of this work is that a multi-body musculo-skeletal simulation in Open-Sim can approximate the whole-body sagittal-plane dynamics of the passive SLIP model. By adding a plugin controller to the OpenSim environment, the Clock-Torqued-SLIP dynamics can be approximated in OpenSim. To change between walking and running, only one parameter representing the preferred period of a stride is changed. The result is a robustly stable simulation of the center-of-mass locomotion for both walking and running that could serve as a first step toward increasingly anatomically accurate and robustly stable musculo-skeletal simulations.


2009 ◽  
Vol 131 (3) ◽  
Author(s):  
S. Srinivasan ◽  
E. R. Westervelt ◽  
A. H. Hansen

This paper presents an extension of a recently developed low-dimensional modeling approach for normal human gait to the modeling of asymmetric gait. The asymmetric model is applied to analyze the gait dynamics of a transtibial prosthesis user, specifically the changes in joint torque and joint power costs that occur with variations in sagittal-plane alignment of the prosthesis, mass distribution of the prosthesis, and roll-over shape of the prosthetic foot being used. The model predicts an increase in cost with addition of mass and a more distal location of the mass, as well as the existence of an alignment at which the costs are minimized. The model’s predictions also suggest guidelines for the selection of prosthetic feet and suitable alignments. The results agree with clinical observations and results of other gait studies reported in the literature. The model can be a useful analytical tool for more informed design and selection of prosthetic components, and provides a basis for making the alignment process systematic.


2017 ◽  
Vol 36 (4) ◽  
pp. 436-455 ◽  
Author(s):  
Salman Faraji ◽  
Auke J Ijspeert

In this paper, we present a new mechanical model for biped locomotion, composed of three linear pendulums (one per leg and one for the whole upper body) to describe stance, swing and torso dynamics. In addition to a double support phase, this model has different actuation possibilities in the swing hip and stance ankle which produce a broad range of walking gaits. Without the need for numerical time-integration, closed form solutions help to find periodic gaits which could simply scale in certain dimensions to modulate the motion online. Thanks to linearity properties, the proposed model can potentially provide a computationally fast platform for model predictive controllers to predict the future and consider meaningful inequality constraints to ensure feasibility of the motion. Such a property comes from describing dynamics with joint torques directly and therefore, reflecting hardware limitations more precisely, even in the very abstract template space. The proposed model produces human-like torque and ground reaction force profiles, and thus, compared to point-mass models, it is more promising for the generation of dynamic walking trajectories. Despite being linear and lacking many features of human walking like center of mass excursion, knee flexion and ground clearance, we show that the proposed model can explain one of the main optimality trends in human walking, i.e. the nonlinear speed-frequency relationship. In this paper, we mainly focus on describing the model and its capabilities, comparing it with human data and calculating optimal human gait variables. Setting up control problems and advanced biomechanical analysis remains for future works.


2021 ◽  
Vol 13 (10) ◽  
pp. 5598
Author(s):  
Stasys Mizaras ◽  
Diana Lukmine

Effective formation and implementation of forest policy can only be achieved with orientation to the most important goal—increasing society’s welfare. The global problem is, at present, that the impact of forests on society welfare indexes have not been identified. The aim of the study is to design an assessment model and assess the impact of Lithuanian forests on the society welfare index. The impact of forests was determined by multiplying the country’s welfare of society index by the forest contribution coefficient. In this study, to assess the index of the welfare of Lithuanian society, a five-dimensional model with 16 indicators was applied. The study is based on the Eurostat database and on Lithuanian forestry statistics. The Lithuanian welfare of society index calculated according to the model was 51.4% and the contribution of forests in this index was 3.9%. It represented 7.6% of the index of the welfare of society. Forests have the greatest impact in the environmental dimension, according to the assessment results.


2020 ◽  
Vol 4 (1) ◽  
pp. 50-58
Author(s):  
Matthias  Tietsch ◽  
Amir Muaremi ◽  
Ieuan Clay ◽  
Felix Kluge ◽  
Holger Hoefling ◽  
...  

Analyzing human gait with inertial sensors provides valuable insights into a wide range of health impairments, including many musculoskeletal and neurological diseases. A representative and reliable assessment of gait requires continuous monitoring over long periods and ideally takes place in the subjects’ habitual environment (real-world). An inconsistent sensor wearing position can affect gait characterization and influence clinical study results, thus clinical study protocols are typically highly proscriptive, instructing all participants to wear the sensor in a uniform manner. This restrictive approach improves data quality but reduces overall adherence. In this work, we analyze the impact of altering the sensor wearing position around the waist on sensor signal and step detection. We demonstrate that an asymmetrically worn sensor leads to additional odd-harmonic frequency components in the frequency spectrum. We propose a robust solution for step detection based on autocorrelation to overcome sensor position variation (sensitivity = 0.99, precision = 0.99). The proposed solution reduces the impact of inconsistent sensor positioning on gait characterization in clinical studies, thus providing more flexibility to protocol implementation and more freedom to participants to wear the sensor in the position most comfortable to them. This work is a first step towards truly position-agnostic gait assessment in clinical settings.


1998 ◽  
Vol 79 (4) ◽  
pp. 2155-2170 ◽  
Author(s):  
L. Bianchi ◽  
D. Angelini ◽  
G. P. Orani ◽  
F. Lacquaniti

Bianchi, L., D. Angelini, G. P. Orani, and F. Lacquaniti. Kinematic coordination in human gait: relation to mechanical energy cost. J. Neurophysiol. 79: 2155–2170, 1998. Twenty-four subjects walked at different, freely chosen speeds ( V) ranging from 0.4 to 2.6 m s−1, while the motion and the ground reaction forces were recorded in three-dimensional space. We considered the time course of the changes of the angles of elevation of the trunk, pelvis, thigh, shank, and foot in the sagittal plane. These angles specify the orientation of each segment with respect to the vertical and to the direction of forward progression. The changes of the trunk and pelvis angles are of limited amplitude and reflect the dynamics of both right and left lower limbs. The changes of the thigh, shank, and foot elevation are ample, and they are coupled tightly among each other. When these angles are plotted one versus the others, they describe regular loops constrained on a plane. The plane of angular covariation rotates, slightly but systematically, along the long axis of the gait loop with increasing V. The rotation, quantified by the change of the direction cosine of the normal to the plane with the thigh axis ( u 3 t ), is related to a progressive phase shift between the foot elevation and the shank elevation with increasing V. As a next step in the analysis, we computed the mass-specific mean absolute power ( P u ) to obtain a global estimate of the rate at which mechanical work is performed during the gait cycle. When plotted on logarithmic coordinates, P u increases linearly with V. The slope of this relationship varies considerably across subjects, spanning a threefold range. We found that, at any given V > 1 m s−1, the value of the plane orientation ( u 3 t ) is correlated with the corresponding value of the net mechanical power ( P u ). On the average, the progressive rotation of the plane with increasing V is associated with a reduction of the increment of P u that would occur if u 3 t remained constant at the value characteristic of low V. The specific orientation of the plane at any given speed is not the same in all subjects, but there is an orderly shift of the plane orientation that correlates with the net power expended by each subject. In general, smaller values of u 3 t tend to be associated with smaller values of P u and vice versa. We conclude that the parametric tuning of the plane of angular covariation is a reliable predictor of the mechanical energy expenditure of each subject and could be used by the nervous system for limiting the overall energy expenditure.


2011 ◽  
Vol 137 ◽  
pp. 72-76
Author(s):  
Wei Zhang ◽  
Xian Wen ◽  
Yan Qun Jiang

A proper orthogonal decomposition (POD) method is applied to study the global stability analysis for flow past a stationary circular cylinder. The flow database at Re=100 is obtained by CFD software, i.e. FLUENT, with which POD bases are constructed by a snapshot method. Based on the POD bases, a low-dimensional model is established for solving the two-dimensional incompressible NS equations. The stability of the flow solution is evaluated by a POD-Chiba method in the way of the eigensystem analysis for the velocity disturbance. The linear stability analysis shows that the first Hopf bifurcation takes place at Re=46.9, which is in good agreement with available results by other high-order accurate stability analysis methods. However, the calculated amount of POD is little, which shows the availability and advantage of the POD method.


2001 ◽  
Author(s):  
Randall S. Gemmen

Abstract The effect of inverter ripple current on fuel cell stack performance and stack lifetime remains uncertain. This paper provides a first attempt to examine the impact of inverter load dynamics on the fuel cell. Since reactant utilization is known to impact the mechanical state of a fuel cell, it is suggested that the varying reactant conditions surrounding the cell govern, at least in part, the lifetime of the cells. This paper investigates these conditions through the use of a dynamic model for the bulk conditions within the stack, as well as a one-dimensional model for the detailed mass transport occurring within the electrode of a cell. These two independent modeling approaches help to verify their respective numerical procedures. In this work, the inverter load is imposed as a boundary condition to the models. Results show the transient behavior of the reactant concentrations within the stack, and of the mass diffusion within the electrode under inverter loads with frequencies between 30 Hz and 1250 Hz.


2013 ◽  
Vol 727 ◽  
pp. 236-255 ◽  
Author(s):  
D. Vigolo ◽  
I. M. Griffiths ◽  
S. Radl ◽  
H. A. Stone

AbstractUnderstanding the behaviour of particles entrained in a fluid flow upon changes in flow direction is crucial in problems where particle inertia is important, such as the erosion process in pipe bends. We present results on the impact of particles in a T-shaped channel in the laminar–turbulent transitional regime. The impacting event for a given system is described in terms of the Reynolds number and the particle Stokes number. Experimental results for the impact are compared with the trajectories predicted by theoretical particle-tracing models for a range of configurations to determine the role of the viscous boundary layer in retarding the particles and reducing the rate of collision with the substrate. In particular, a two-dimensional model based on a stagnation-point flow is used together with three-dimensional numerical simulations. We show how the simple two-dimensional model provides a tractable way of understanding the general collision behaviour, while more advanced three-dimensional simulations can be helpful in understanding the details of the flow.


Sign in / Sign up

Export Citation Format

Share Document