The Impedance of Curved Artery Models

1983 ◽  
Vol 105 (3) ◽  
pp. 275-282 ◽  
Author(s):  
S. G. Kang ◽  
J. M. Tarbell
Keyword(s):  
Aortic Arch ◽  
Steady Flow ◽  
Flow Rate ◽  
Straight Tube ◽  
Flow Conditions ◽  
Mean Flow ◽  
Periodic Flows ◽  
Curved Artery ◽  
Flow Impedance ◽  
Drop Flow

The impedance (pressure drop/flow rate) of four curved artery models has been determined experimentally for steady and periodic flows simulating conditions in the aortic arch. Steady flow results indicate that very short entry lengths are required for flow development in curved artery models, and impedance is elevated above straight tube values by a factor of 3–4 for mean flow conditions in the aortic arch. Results for periodic flow with a nonzero mean show a significant elevation of mean flow impedance relative to values for steady flow at the mean flow rate—a factor of 2–3 for aortic arch flow conditions. The impedance of the first harmonic of periodic flows follows straight tube theory at high values of the unsteadiness parameter in agreement with available theory for curved tubes. The implications of the impedance measurements for wall shear stress in the aortic arch are discussed.

Compliance Effect on the Flow Condition in Vascular In Vitro Experiments

2018 ◽  
Author(s):  
Masami Matsuura ◽  
Simon Tupin ◽  
Makoto Ohta
Keyword(s):  
Flow Rate ◽  
Time Lag ◽  
Flow Patterns ◽  
Poly Vinyl Alcohol ◽  
Circulation System ◽  
Straight Tube ◽  
Flow Conditions ◽  
Flow Properties ◽  
Clinician Training

Endovascular treatment has become the standard for intracranial aneurysm management. In vitro systems including an artery model are required for devices evaluation and clinician training. Although silicone is usually use for such model, its compliance is known to be lower than blood vessels. The purpose of this study was to analyze the influence of model material compliance on flow properties. Silicone and 12 [wt%] poly (vinyl alcohol) hydrogel (PVA-H) were used to create two box-shaped models of significantly different compliance. The inner lumen geometry was a 4 [mm] diameter straight tube (parent vessel) and a 10 [mm] diameter sphere representing the aneurysm. A blood-mimicking fluid made of a mixture of glycerin, water and sodium iodide was used to reproduce the viscosity and density of blood and fit models refractive index. The circulation system consisted of a pulsatile blood pump and resistance valve. A flow rate of 250±50 [ml/min] and pressure from 75 to 115 [mmHg] were set inside the model. Pressure and flow rate sensors were used to monitor flow conditions before and after the model. Particle image velocimetry (PIV) was performed to record the difference of flow patterns inside the aneurysm of both model using a Nd:YAG solid laser system and fluorescent particles. Results revealed a significant change of flow conditions due to model compliance. Attenuation of the flow rate pulse was recorded between the inlet and the outlet of the both model. This attenuation was 51% for PVA-H model. Moreover, a time lag between outlet pressure and outlet flow rate curves was recorded in both model. This time lag was longer with the PVA-H model, as this model exhibit a greater compliance. PIV experiments revealed significant changes of flow patterns and velocity inside the aneurysm. Because of its high compliance, PVA-H model walls moved under the pulsatile conditions. A change of flow direction and decrease of its velocity were observed near the proximal wall of the aneurysm, compared to the silicone model. Such differences might modify the stress on the wall of the aneurysm. To conclude, our experiments revealed that compliance has significant impacts on flow properties and should be taken into account for in vitro vascular model manufacturing.

Evaluation of Magnetic Resonance Velocimetry for Steady Flow

1990 ◽  
Vol 112 (4) ◽  
pp. 464-472 ◽  
Author(s):  
D. N. Ku ◽  
C. L. Biancheri ◽  
R. I. Pettigrew ◽  
J. W. Peifer ◽  
C. P. Markou ◽  
...  
Keyword(s):  
Magnetic Resonance ◽  
Steady Flow ◽  
Laser Doppler Anemometry ◽  
Flow Behavior ◽  
Velocity Profiles ◽  
Secondary Flows ◽  
Whole Body ◽  
Straight Tube ◽  
Flow Conditions ◽  
Wide Range

Whole body magnetic resonance (MR) imaging has recently become an important diagnostic tool for cardiovascular diseases. The technique of magnetic resonance phase velocity encoding allows the quantitative measurement of velocity for an arbitrary component direction. A study was initiated to determine the ability and accuracy of MR velocimetry to measure a wide range of flow conditions including flow separation, three-dimensional secondary flow, high velocity gradients, and turbulence. A steady flow system pumped water doped with manganese chloride through a variety of test sections. Images were produced using gradient echo sequences on test sections including a straight tube, a curved tube, a smoothly converging-diverging nozzle, and an orifice. Magnetic resonance measurements of laminar and turbulent flows were depicted as cross-sectional velocity profiles. MR velocity measurements revealed such flow behavior as spatially varying velocity, recirculation and secondary flows over a wide range of conditions. Comparisons made with published experimental laser Doppler anemometry measurements and theoretical calculations for similar flow conditions revealed excellent accuracy and precision levels. The successful measurement of velocity profiles for a variety of flow conditions and geometries indicate that magnetic resonance imaging is an accurate, non-contacting velocimeter.

scholarly journals Effect of Flow on Various Helmholtz Resonators

2020 ◽  
Vol 25 (1) ◽  
pp. 73-78
Author(s):  
Hyunsu Kim ◽  
Iljae Lee
Keyword(s):  
Transmission Loss ◽  
Flow Conditions ◽  
Mean Flow ◽  
Direct Flow ◽  
Acoustic Performance ◽  
Helmholtz Resonators ◽  
Flow Impedance ◽  
Flow Effects ◽  
Two Peaks ◽  
The Impact

The acoustic performance of Helmholtz resonators with different configurations in the presence of mean flow is experimentally investigated. The transmission loss of Helmholtz resonators is measured using a flow-impedance tube setup to identify mean flow effects. First, Helmholtz resonators under two different flow conditions, grazing and direct flow, are considered at Ma=0.05 and 0.1. Then the impact of mean flow on the transmission loss of Helmholtz resonators with leakage holes is also demonstrated. For Helmholtz resonators with leakage holes, single peak of transmission loss is identified at Ma=0.0 and 0.1. However, two peaks appear at Ma=0.05 as the number of opening holes increases. The experimental results show that the effect of mean flow strongly depends on the configurations of Helmholtz resonators and the conditions of mean flow. Thus the variation of acoustic performance due to mean flow should be considered in the design of Helmholtz resonators.

scholarly journals Quantifying the Effects of Wave—Current Interactions on Tidal Energy Resource at Sites in the English Channel Using Coupled Numerical Simulations

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3625
Author(s):  
Jon Hardwick ◽  
Ed B. L. Mackay ◽  
Ian G. C. Ashton ◽  
Helen C. M. Smith ◽  
Philipp R. Thies
Keyword(s):  
Wave Model ◽  
Tidal Energy ◽  
English Channel ◽  
Flow Conditions ◽  
Mean Flow ◽  
Radiation Stress ◽  
Large Wave ◽  
Stress Gradients ◽  
The Mean ◽  
Flow Power

Numerical modeling of currents and waves is used throughout the marine energy industry for resource assessment. This study compared the output of numerical flow simulations run both as a standalone model and as a two-way coupled wave–current simulation. A regional coupled flow-wave model was established covering the English Channel using the Delft D-Flow 2D model coupled with a SWAN spectral wave model. Outputs were analyzed at three tidal energy sites: Alderney Race, Big Roussel (Guernsey), and PTEC (Isle of Wight). The difference in the power in the tidal flow between coupled and standalone model runs was strongly correlated to the relative direction of the waves and currents. The net difference between the coupled and standalone runs was less than 2.5%. However, when wave and current directions were aligned, the mean flow power was increased by up to 7%, whereas, when the directions were opposed, the mean flow power was reduced by as much as 9.6%. The D-Flow Flexible Mesh model incorporates the effects of waves into the flow calculations in three areas: Stokes drift, forcing by radiation stress gradients, and enhancement of the bed shear stress. Each of these mechanisms is discussed. Forcing from radiation stress gradients is shown to be the dominant mechanism affecting the flow conditions at the sites considered, primarily caused by dissipation of wave energy due to white-capping. Wave action is an important consideration at tidal energy sites. Although the net impact on the flow power was found to be small for the present sites, the effect is site specific and may be significant at sites with large wave exposure or strong asymmetry in the flow conditions and should thus be considered for detailed resource and engineering assessments.

scholarly journals Detonation initiation by shock focusing at elevated pressure conditions in a pulse detonation combustor

2020 ◽  
Vol 12 ◽  
pp. 175682772092171
Author(s):  
Fabian E Habicht ◽  
Fatma C Yücel ◽  
Joshua AT Gray ◽  
Christian O Paschereit
Keyword(s):  
Success Rate ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Initial Pressure ◽  
Detonation Initiation ◽  
Major Influence ◽  
Mean Flow ◽  
Shock Focusing ◽  
Pulse Detonation

This work contains experimental investigations on the correlation of the detonation initiation process via a shock-focusing device with various initial pressures and mass flow rates. A pulse detonation combustor is operated with stoichiometric hydrogen--air--oxygen mixtures in single cycle operation. A rotationally symmetric shock-focusing geometry evokes the onset of a detonation by the focusing of the reflected leading shock wave, while a blockage plate at the rear end of the test rig is applied to induce an elevated initial pressure. The results show that the reactivity has a major influence on the success rate of detonation initiation. However, measurements with different blockage plates suggest that the mass flow rate has to be considered as well when predicting the success rate. Three main statements can be drawn from the results. (1) An increase in the mean flow velocity induces higher velocity fluctuations which result in a stronger leading shock ahead of the accelerating deflagration front. (2) An increase in the initial static pressure reduces the critical shock strength that must be exceeded to ensure successful detonation initiation by shock focusing. (3) Since the initial pressure is directly linked to the mass flow rate, these contrary trends can cancel each other out, which could be observed for 40% vol. of oxygen in the oxidizer. High-speed images were taken, which confirm that the detonation is initiated in the center of the converging--diverging nozzle due to focusing of the leading shock.

scholarly journals Effect of Fluid Flow on the Corrosion Performance of as-Cast and Heat-Treated Nickel Aluminum Bronze Alloy (UNS C95800) in Saline Solution

2021 ◽  
Vol 2 (1) ◽  
pp. 61-77
Author(s):  
Hamid Reza Jafari ◽  
Ali Davoodi ◽  
Saman Hosseinpour
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Flow Rate ◽  
Solution Temperature ◽  
Aluminum Bronze ◽  
Nickel Aluminum ◽  
Nacl Solution ◽  
Flow Conditions ◽  
Heat Treated ◽  
Nickel Aluminum Bronze

In this work, the corrosion behavior and surface reactivity of as-cast and heat-treated nickel aluminum bronze casting alloy (UNS C95800) in 3.5 wt% NaCl solution is investigated under stagnant and flow conditions. Increasing flow rate conditions are simulated using a rotating disk electrode from 0 to 9000 revolutions per minute (rpm). Optical micrographs confirm the decrease in the phase fraction of corrosion-sensitive β phase in the microstructure of C95800 after annealing, which, in turn, enhances the corrosion resistance of the alloy. Electrochemical studies including open circuit potentiometry, potentiodynamic polarization, and electrochemical impedance spectroscopy are performed to assess the effect of flow rate and heat treatment on the corrosion of samples at 25 and 40 °C in 3.5 wt% NaCl solution. For both as-cast and heat-treated samples, increasing the flow rate (i.e., electrode rotating rate) linearly reduces the corrosion resistance, indicating that the metal dissolution rate is significantly affected by hydrodynamic flow. Increasing the solution temperature negatively impacts the corrosion behavior of the as-cast and heat-treated samples at all flow conditions.

scholarly journals Net-exergetic, hydraulic and thermal optimization of coaxial heat exchangers using fixed flow conditions instead of fixed flow rates

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Tobias Blanke ◽  
Markus Hagenkamp ◽  
Bernd Döring ◽  
Joachim Göttsche ◽  
Vitali Reger ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Laminar Flow ◽  
Mass Flow ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Circular Ring ◽  
Flow Conditions ◽  
Flow Rates ◽  
Mass Flow Rates ◽  
Pipe Radius

AbstractPrevious studies optimized the dimensions of coaxial heat exchangers using constant mass flow rates as a boundary condition. They show a thermal optimal circular ring width of nearly zero. Hydraulically optimal is an inner to outer pipe radius ratio of 0.65 for turbulent and 0.68 for laminar flow types. In contrast, in this study, flow conditions in the circular ring are kept constant (a set of fixed Reynolds numbers) during optimization. This approach ensures fixed flow conditions and prevents inappropriately high or low mass flow rates. The optimization is carried out for three objectives: Maximum energy gain, minimum hydraulic effort and eventually optimum net-exergy balance. The optimization changes the inner pipe radius and mass flow rate but not the Reynolds number of the circular ring. The thermal calculations base on Hellström’s borehole resistance and the hydraulic optimization on individually calculated linear loss of head coefficients. Increasing the inner pipe radius results in decreased hydraulic losses in the inner pipe but increased losses in the circular ring. The net-exergy difference is a key performance indicator and combines thermal and hydraulic calculations. It is the difference between thermal exergy flux and hydraulic effort. The Reynolds number in the circular ring is instead of the mass flow rate constant during all optimizations. The result from a thermal perspective is an optimal width of the circular ring of nearly zero. The hydraulically optimal inner pipe radius is 54% of the outer pipe radius for laminar flow and 60% for turbulent flow scenarios. Net-exergetic optimization shows a predominant influence of hydraulic losses, especially for small temperature gains. The exact result depends on the earth’s thermal properties and the flow type. Conclusively, coaxial geothermal probes’ design should focus on the hydraulic optimum and take the thermal optimum as a secondary criterion due to the dominating hydraulics.

EXTRACTION OF MINUTE GAS BUBBLES FROM LIQUIDS FLOWING IN A SIMULATED CARDIOPULMONARY BYPASS SYSTEM BY A VENTURI-ASPIRATOR UNIT

2002 ◽  
Vol 02 (03n04) ◽  
pp. 297-312
Author(s):  
WEN-JEI YANG ◽  
AMR EID ◽  
R. ECHIGO
Keyword(s):  
Cardiopulmonary Bypass ◽  
Flow Rate ◽  
Whole Blood ◽  
Pressure Difference ◽  
Gas Bubbles ◽  
Blood Oxygenation ◽  
Straight Tube ◽  
Suction Pressure ◽  
Total Flow ◽  
Total Flow Rate

An experimental study is performed to extract minute gas bubbles from liquids flowing in a simulated cardiopulmonary bypass system using a Venturi-aspirator unit. In other words, oxygen bubbles in oxygenated blood are simulated by air bubbles in water with AP30 (about same viscosity as whole blood). This study is intended to determine the feasibility of using a Venturi aspirator unit to extract minute gas bubbles from a simulated cardiopulmonary bypass system. Testing of the Venturi-type bubble extraction is carried out using three different test sections. Two Venturis are used, and a straight tube configuration is used as a control. The two Venturis are similar, with the exception that one has a longer inlet cone which causes the entering liquid to accelerate at a slower rate. Results are obtained for effectiveness of the aspirator unit as functions of total flow rate, extraction suction, suction pressure difference, and hydraulic head. It is concluded from the study that:(i) The effectiveness of the Venturis is typically between 90 and 100 percent. It increases with an increase in suction or suction pressure difference but decreases with an increase in total flow rate.(ii) The Venturi is most suitable for extraction of minute gas bubbles, especially for use with AP30 (whole blood), which yields substantially higher effectiveness than water.(iii) It is anticipated that a Venturi-aspirator unit can be superior to other bubble separation device as the cardiopulmonary bypass system for applications in extra corporeal blood oxygenation.

A particle image velocimetry study on the pulsatile flow characteristics in straight tubes with an asymmetric bulge

2000 ◽  
Vol 214 (5) ◽  
pp. 655-671 ◽  
Author(s):  
S C M Yu ◽  
J B Zhao
Keyword(s):  
Particle Image Velocimetry ◽  
Steady Flow ◽  
Pulsatile Flow ◽  
Flow Condition ◽  
Particle Image ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Working Fluid ◽  
Flow Conditions ◽  
Image Velocimetry

Flow characteristics in straight tubes with an asymmetric bulge have been investigated using particle image velocimetry (PIV) over a range of Reynolds numbers from 600 to 1200 and at a Womersley number of 22. A mixture of glycerine and water (approximately 40:60 by volume) was used as the working fluid. The study was carried out because of their relevance in some aspects of physiological flows, such as arterial flow through a sidewall aneurysm. Results for both steady and pulsatile flow conditions were obtained. It was found that at a steady flow condition, a weak recirculating vortex formed inside the bulge. The recirculation became stronger at higher Reynolds numbers but weaker at larger bulge sizes. The centre of the vortex was located close to the distal neck. At pulsatile flow conditions, the vortex appeared and disappeared at different phases of the cycle, and the sequence was only punctuated by strong forward flow behaviour (near the peak flow condition). In particular, strong flow interactions between the parent tube and the bulge were observed during the deceleration phase. Stents and springs were used to dampen the flow movement inside the bulge. It was found that the recirculation vortex could be eliminated completely in steady flow conditions using both devices. However, under pulsatile flow conditions, flow velocities inside the bulge could not be suppressed completely by both devices, but could be reduced by more than 80 per cent.

scholarly journals Temperature log simulations in high-enthalpy boreholes

2019 ◽  
Vol 7 (1) ◽  
Author(s):  
Jia Wang ◽  
Fabian Nitschke ◽  
Maziar Gholami Korzani ◽  
Thomas Kohl
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Temperature Gradient ◽  
Flow Rate ◽  
Fluid Loss ◽  
Flow Conditions ◽  
Flow Rates ◽  
High Enthalpy ◽  
Fluid Losses ◽  
Lateral Heat

Abstract Temperature logs have important applications in the geothermal industry such as the estimation of the static formation temperature (SFT) and the characterization of fluid loss from a borehole. However, the temperature distribution of the wellbore relies on various factors such as wellbore flow conditions, fluid losses, well layout, heat transfer mechanics within the fluid as well as between the wellbore and the surrounding rock formation, etc. In this context, the numerical approach presented in this paper is applied to investigate the influencing parameters/uncertainties in the interpretation of borehole logging data. To this end, synthetic temperature logs representing different well operation conditions were numerically generated using our newly developed wellbore simulator. Our models account for several complex operation scenarios resulting from the requirements of high-enthalpy wells where different flow conditions, such as mud injection with- and without fluid loss and shut-in, occur in the drill string and the annulus. The simulation results reveal that free convective heat transfer plays an important role in the earlier evolution of the shut-in-time temperature; high accuracy SFT estimation is only possible when long-term shut-in measurements are used. Two other simulation scenarios for a well under injection conditions show that applying simple temperature correction methods on the non-shut-in temperature data could lead to large errors for SFT estimation even at very low injection flow rates. Furthermore, the magnitude of the temperature gradient increase depends on the flow rate, the percentage of fluid loss and the lateral heat transfer between the fluid and the rock formation. As indicated by this study, under low fluid losses (< 30%) or relatively higher flow rates (> 20 L/s), the impact of flow rate and the lateral heat transfer on the temperature gradient increase can be ignored. These results provide insights on the key factors influencing the well temperature distribution, which are important for the choice of the drilling data to estimate SFT and the design of the inverse modeling scheme in future studies to determine an accurate SFT profile for the high-enthalpy geothermal environment.

Sign in / Sign up

Export Citation Format

Share Document