Flow Regime Definition for Flow Between Corotating Disks

1974 ◽  
Vol 96 (1) ◽  
pp. 29-34 ◽  
Author(s):  
L. L. Pater ◽  
E. Crowther ◽  
W. Rice

Experimental data and results are presented for the flow of an incompressible Newtonian fluid, with full admission, between closely spaced corotating disks, and for both radially inward and radially outward throughflows. The data consist of the measured radial pressure distribution together with flow visualization by means of injected dye, over a very wide range of parameters descriptive of the flows. From the data, the combinations of the parameters corresponding with laminar and with turbulent flow are determined; that is, the data are sufficient to define the flow regimes. Furthermore, for laminar flow, both the pressure distribution data and the flow visualization data confirm the adequacy of earlier analytical results for use in the design of practical devices incorporating these flows, such as multiple disk pumps and turbines.

1970 ◽  
Vol 37 (3) ◽  
pp. 844-849 ◽  
Author(s):  
R. Adams ◽  
W. Rice

Experimental results are presented for the flow of an incompressible Newtonian fluid, with full admission, between closely spaced corotating disks. The radial pressure distribution is shown to coincide very closely with analytical results for laminar flow earlier presented by other investigators, over a wide range of the parameters pertinent to the flow description. A referenced analytical model for laminar flow between corotating disks is thus given credence. The experimental arrangement and procedure are described and a supporting uncertainty analysis is presented.


1946 ◽  
Vol 13 (2) ◽  
pp. A101-A105
Author(s):  
R. C. Binder ◽  
J. E. Busher

Abstract The pipe friction coefficient for true fluids is usually expressed as a function of Reynolds number. This method of organizing data has been extended to tests on the flow of different suspensions which behaved as ideal plastics in the laminar-flow range and as true fluids in the turbulent-flow range. In the laminar-flow range, Reynolds number below about 2100, the denominator in Reynolds number is taken as the apparent viscosity. The apparent viscosity can be determined from the yield value and the coefficient of rigidity. In the turbulent-flow range, the denominator in Reynolds number is an equivalent or turbulent viscosity equal to the dynamic viscosity of a true fluid having the same friction coefficient, velocity, diameter, and density as that of the plastic. The various experimental data on plastics correlate well with this extension of the method for true fluids.


Author(s):  
Christian Weinmu¨ller ◽  
Dimos Poulikakos

Microfluidics has experienced a significant increase in research activities in recent years with a wide range of applications emerging, such as micro heat exchangers, energy conversion devices, microreactors, lab-on-chip devices and micro total chemical analysis systems (μTAS). Efforts to enhance or extend the performance of single phase microfluidic devices are met by two-phase flow systems [1, 2]. Essential for the design and control of microfluidic systems is the understanding of the fluid/hydrodynamic behavior, especially pressure drop correlations. These are well established for single phase flow, however, analytical correlations for two-phase flow only reflect experimentally obtained values within an accuracy of ± 50% [3, 4]. The present study illustrates the effect of two-phase flow regimes on the pressure drop. Experimental measurement data is put into relation of calculated values based on established correlations of Lockhart-Martinelli with Chisholm modifications for macroscopic flows [5, 6] and Mishima-Hibiki modifications for microscale flows [7]. Further, the experimental pressure drop data is superimposed onto two-phase flow maps to identify apparent correlations of pressure drop abnormalities and flow regimes. The experiments were conducted in a square microchannel with a width of 200 μm. Optical access is guaranteed by an anodically bonded glass plate on a MEMS fabricated silicon chip. Superficial velocities range from 0.01 m/s to 1 m/s for the gas flow and from 0.0001 m/s to 1 m/s for the liquid flow with water as liquid feed and CO2 as gas. The analysis of the flow regimes was performed by imaging the distinct flow regimes by laser induced fluorescence microscopy, employing Rhodamine B as the photosensitive dye. The pressure drop was synchronically recorded with a 200 mbar, 2.5 bar and 25 bar differential pressure transmitter and the data was exported via a LabView based software environment, see Figure 1. Figure 2 illustrates the experimentally obtained pressure drop in comparison to the calculated values based on the Lockhard-Martinelli correlation with the Chisholm modification and the Mishima-Hibiki modification. For both cases the predications underestimate the two-phase pressure drop by more than 50%. Nevertheless, the regression of the experimental data has an offset of linear nature. Two-phase flow is assigned to flow regime maps of bubbly, wedging, slug or annular flow defined by superficial gas and liquid velocities. In Figure 3 the pressure drop is plotted as a surface over the corresponding flow regime map. Transition lines indicate a change of flow regimes enclosing an area of an anticline in the pressure data. In the direct comparison between the calculated and the measured values, the two surfaces show a distinct deviation. Especially, the anticline of the experimental data is not explained by the analytical correlations. Figure 4 depicts the findings of Figure 3 at a constant superficial velocity of 0.0232 m/s. The dominant influence of the flow regimes on the pressure drop becomes apparent, especially in the wedging flow regime. The evident deviation of two-phase flow correlations for the pressure drop is based on omitting the influence of the flow regimes. In conclusion, the study reveals a strong divergence of pressure drop measurements in microscale two-phase flow from established correlations of Lockhart-Martinelli and recognized modifications. In reference to [8, 9], an analytical model incorporating the flow regimes and, hence, predicting the precise pressure drop would be of great benefit for hydrodynamic considerations in microfluidics.


Author(s):  
Si-pu Guo ◽  
Zhao-zan Feng ◽  
Ze-cong Fang ◽  
Wei Li ◽  
Jin-liang Xu ◽  
...  

Nanofluids are colloidal suspensions of nano-scale particles in water, or other base fluids. In this paper, the effect of natural convection on laminar flow of nanofluids in a horizontal tube has been addressed. The obtained experimental data could not be reconciled with existing correlations over a wide range of Prandtl number under laminar mixed convection. Three improved correlations have been derived by using single-phase fluid approach. These correlations fit our data to within ± 10 % and also agree with the data in literature quite well. Such results verify that nanofluids can be treated as a homogeneous mixture with effective thermophysical properties. Utimately, the new correlations have grasped the essence of natural convection and can reduce to both normal forced convection and pure natural convection equations at limiting cases.


1967 ◽  
Vol 89 (2) ◽  
pp. 143-153 ◽  
Author(s):  
F. K. Orcutt ◽  
E. B. Arwas

The steady-state and dynamic characteristics of a full circular bearing and a centrally loaded, 100 deg, arc bearing are calculated for a range of eccentricity ratios to 0.95 and of mean Reynolds numbers to 13,300, and presented in design charts. These are compared with the measured performance of these bearings over the same ranges of the operating parameters. There is good correlation between the theoretical and test data, leading to the conclusion that the present turbulent lubrication analysis may be used to obtain general design data for self-acting bearings, operating in the superlaminar flow regime, to supplement that presently existing for laminar flow bearings.


1996 ◽  
Vol 329 ◽  
pp. 373-388 ◽  
Author(s):  
Hiroshi Ishigaki

When a curved pipe rotates about the centre of curvature, the fluid flowing in it is subjected to both Coriolis and centrifugal forces. Based on the analogy between laminar flows in stationary curved pipes and in orthogonally rotating pipes, the flow characteristics of fully developed laminar flow in rotating curved pipes are made clear and definite by similarity arguments, computational studies and using experimental data. Similarity arguments clarify that the flow characteristics in loosely coiled rotating pipes are governed by three parameters: the Dean number KLC, a body force ratio F and the Rossby number Ro. As the effect of Ro is negligible when Ro is large, computational results are presented for this case first, and then the effect of Ro is studied. Flow structure and friction factor are studied in detail. Variations of flow structure show secondary flow reversal at F ≈ −1, where the two body forces are of the same order but in opposite directions. It is also shown how the Taylor–Proudman effect dominates the flow structure when Ro is small. Computed curves of the friction factor for constant Dean number have their minimum at F ≈ −1. A composite parameter KL is introduced as a convenient governing parameter and used to correlate the characteristics. By applying KL to the analogy formula previously derived for two limiting flows, a semi-empirical formula for the friction factor is presented, which shows good agreement with the experimental data for a wide range of the parameters.


Author(s):  
Dillon R. Shaver ◽  
Lane B. Carasik ◽  
Elia Merzari ◽  
Nate Salpeter ◽  
Edward Blandford

The development of fluoride salt-cooled high-temperature reactors (FHRs) for nuclear power generation relies on the development of new technologies. Of the potential options being explored, twisted elliptical tube geometries for heat exchanger design are promising based on usage in other industries. They are expected to offer significant enhancement in heat transfer with only a marginal increase in frictional losses. This allows them to be deployed in relatively compact designs that are well suited for FHRs. The presented work focuses on the computational fluid dynamics (CFD) simulations of heated molten salt flows through various twisted elliptical tube geometries at low modified Froude numbers. The objectives of this work are to evaluate the available correlations at lower Froude numbers and to determine the impact of using non-zero tube to tube spacing to resolve contact points or numerical singularities for future CFD simulations efforts The spectral element CFD code Nek5000 was used for all simulations, which were performed in periodic domains of triangular (hexagonal) and square unit cells surrounding a single tube through a complete twist using an explicit filtering large eddy simulation (LES) method. Simulations were used to para-metrically test the effects of tube-to-tube spacing for laminar and turbulent flow regimes on frictional pressure drop and heat transfer. The tested Reynolds numbers covered both laminar flow and fully developed turbulent flow (90 < Re < 12200). The tested SL/dmax ratios cover the range of 1.02 to 1.08 for both unit cell types. At moderate Reynolds number and comparitively high modified Froude number, excellent agreement for the Nusselt number was observed between simulations and the applicable correlation. As Froude number was decreased towards the bounds of the correlation, the agreement worsened. Cases were then simulated at low Froude number, testing the effects of tube spacing. It was determined that the laminar case for the square unit cell is the most affected by increasing SL/dmax and the gap size should be minimized to mitigate this. Whereas in the triangular unit cell the laminar flow regime is more significantly impacted by increasing SL/dmax compared to the turbulent flow regime which was only marginally impacted.


2021 ◽  
Author(s):  
Azad Hussain ◽  
Muhammad Arsaln ◽  
Ali Hassan ◽  
Aysha Rehman

Abstract This paper investigates time-dependent compressible steam laminar flow coupled with heat transfer in fluids in a squared cylinder. The present problem has been designed in COMSOL-Multiphysics. The laminar flow is selected keeping the Mac number low. The flow possesses a no-slip condition with the wall of geometry. The pressure kept on flow is 0 Pas and the temperature of the flow regime is 305.13. The flow is initiated with a velocity of 0.5m/s. The effects of time on velocity distribution and pressure distribution are described with the help of graphs. Different results like drag coefficient, lift coefficient, heat distributions are also discussed. The technique used to solve modeled problem is BDF.


Author(s):  
Gian Piero Celata

The objective of the present paper is to provide a general overview of the research carried out so far in single-phase heat transfer and flow in capillary (micro) pipes. Laminar flow and laminar-to-turbulent flow transition are analyzed in detail in order to clarify the discrepancies among the results obtained by different researchers. Experiments performed in the ENEA laboratory indicate that in laminar flow regime the friction factor is in good agreement with the Hagen-Poiseuille theory for Reynolds number below 600–800. For higher values of Reynolds number, experimental data depart from the Hagen-Poiseuille law to the side of higher f values. The transition from laminar-to-turbulent flow occurs for Reynolds number in the range 1800–2500. Heat transfer experiments show that heat transfer correlations in laminar and turbulent regimes, developed for conventional (macro) tubes, are not properly adequate for heat transfer rate prediction in microtubes.


Sign in / Sign up

Export Citation Format

Share Document