Investigation of the High Speed Rolling Bearing Temperature Rise With Oil-Air Lubrication

2011 ◽  
Vol 133 (2) ◽  
Author(s):  
Shuyun Jiang ◽  
Hebing Mao
Keyword(s):  
Temperature Rise ◽  
High Speed ◽  
Ball Bearing ◽  
Rotation Speed ◽  
Rolling Bearing ◽  
Operating Conditions ◽  
Steel Ball ◽  
Pipe Length ◽  
Air Lubrication ◽  
Hybrid Ceramic

The oil-air lubrication system has been widely used for rolling ball bearing. However, as the rotation speed increases, the temperature rise will increase dramatically, resulting in shortening the service life of the ball bearing. The existing literature has offered valuable fundamental data about the oil-air lubrication of rolling bearing; however, there are still some problems that concerned the oil-air lubrication, which are not addressed. In this study, an experiment setup to investigate the oil-air lubrication for the high speed ball bearing has been developed, and performance tests of hybrid ceramic and steel ball bearings under the extensive operating conditions including oil-air supply pipe length, bearing preload, lube interval, oil type, oil viscosity, nozzle design, and rotation speed have been conducted. The test results show that the bearing has the lowest temperature rise with the pipe length of 1.5 m. For the steel ball bearing, the proper preload decreases with increasing of the rotating speed, and the temperature rise of the hybrid ceramic ball bearing is not sensitive to the axial preload. There exists a proper amount of lubricant for the bearing at each rotational speed; and a larger amount of lubricant is required for the bearing as the rotating speed increases. The tested bearings under different speeds have almost the same lowest temperature rise under the lubricant with the viscosity of 100 cSt; a higher or lower viscosity will increase the bearing temperature rises. The nozzle design is an important factor to affect the temperature rise of the ball bearing, and the suitable geometric parameter of the nozzle is closely related to the cage landing method of the bearing. The temperature rise of tested bearings increases with the increase in the rotation speed; and the hybrid ceramic ball bearing always has a lower temperature rise than that of the steel ball bearing at the same operating conditions.

Lubrication and Thermal Failure Mechanism Analysis in High-Speed Angular Contact Ball Bearing

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Wang Yunlong ◽  
Wang Wenzhong ◽  
Li Yulong ◽  
Zhao Ziqiang
Keyword(s):  
Rotational Speed ◽  
High Speed ◽  
Ball Bearing ◽  
Rolling Bearing ◽  
Operating Conditions ◽  
Contact Forces ◽  
Mechanism Analysis ◽  
Angular Contact Ball Bearing ◽  
Thermal Failure ◽  
Lubrication Performance

Lubrication analysis of rolling bearing is often conducted with assumed operating conditions, which does not consider the effect of internal dynamics of rolling bearing. In this paper, the effects of the applied load and bearing rotational speed on the lubrication performance in an angular contact ball bearing are conducted, which combines the bearing dynamic analysis and thermo-elastohydrodynamic lubrication (TEHL) analysis. First, the internal motions and contact forces are obtained from the developed bearing dynamic model, and then were integrated into the TEHL model to investigate the lubrication performance of the bearing. The results show that the rotational speed and external load has significant effects on film thickness, temperature, and power loss; if the improper axial load is applied for certain bearing speed, the lubrication performance will deteriorate and thermal failure may occur; there exists critical load or speed to keep good lubrication performance and avoid thermal failure; the skidding contributes to the thermal failure and bad lubrication performance.

Influence of CrCN Coatings Steel Ball Deposited by Closed Field Unbalanced Magnetron Sputtering on the Performance of Bearing

2015 ◽  
Vol 1088 ◽  
pp. 711-715
Author(s):  
Gui Xi Jia ◽  
Jia Dong Chang ◽  
Xiao Lao Sun ◽  
Yun Peng Chang
Keyword(s):  
Wear Resistance ◽  
Temperature Rise ◽  
High Speed ◽  
Ball Bearing ◽  
Steel Ball ◽  
Closed Field ◽  
Stability Performance ◽  
Unbalanced Magnetron ◽  
Load Carrying ◽  
Speed Performance

The CrCN coatings was deposited on the substrate of GCr15 steel ball by closed field unbalanced magnetron sputter ion plating. The performances of vibration, temperature rise, rotational speed, load carrying ability and wear resistance of CrCN coatings steel ball bearing and uncoated steel ball bearing were tested by a bearing tester, and also comparatively analyzed. Results show that, compared to the uncoated bearing, the CrCN coatings steel ball bearing, in the case of rotational speeds higher than 5 000 rpm, have lower vibration values, especially above 6 000 rpm, the vibration values were significantly reduced, and the coated bearing has vibration stability performance. And the coated bearing has also slower temperature rise performance, excellent high-speed performance, good load carrying capacity characteristics and wear resistance performance etc.

Temperature Rise Prediction of Oil-Air Lubricated Angular Contact Ball Bearings Using Artificial Neural Network

2019 ◽  
Vol 12 (3) ◽  
pp. 248-261
Author(s):  
Baomin Wang ◽  
Xiao Chang
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Temperature Rise ◽  
High Speed ◽  
Ball Bearing ◽  
Influence Factors ◽  
Ball Bearings ◽  
Ann Model ◽  
Angular Contact Ball Bearing ◽  
Artificial Neural

Background: Angular contact ball bearing is an important component of many high-speed rotating mechanical systems. Oil-air lubrication makes it possible for angular contact ball bearing to operate at high speed. So the lubrication state of angular contact ball bearing directly affects the performance of the mechanical systems. However, as bearing rotation speed increases, the temperature rise is still the dominant limiting factor for improving the performance and service life of angular contact ball bearings. Therefore, it is very necessary to predict the temperature rise of angular contact ball bearings lubricated with oil-air. Objective: The purpose of this study is to provide an overview of temperature calculation of bearing from many studies and patents, and propose a new prediction method for temperature rise of angular contact ball bearing. Methods: Based on the artificial neural network and genetic algorithm, a new prediction methodology for bearings temperature rise was proposed which capitalizes on the notion that the temperature rise of oil-air lubricated angular contact ball bearing is generally coupling. The influence factors of temperature rise in high-speed angular contact ball bearings were analyzed through grey relational analysis, and the key influence factors are determined. Combined with Genetic Algorithm (GA), the Artificial Neural Network (ANN) model based on these key influence factors was built up, two groups of experimental data were used to train and validate the ANN model. Results: Compared with the ANN model, the ANN-GA model has shorter training time, higher accuracy and better stability, the output of ANN-GA model shows a good agreement with the experimental data, above 92% of bearing temperature rise under varying conditions can be predicted using the ANNGA model. Conclusion: A new method was proposed to predict the temperature rise of oil-air lubricated angular contact ball bearings based on the artificial neural network and genetic algorithm. The results show that the prediction model has good accuracy, stability and robustness.

Direct Outer Ring Cooling of a High Speed Jet Engine Mainshaft Ball Bearing: Experimental Investigation Results

2010 ◽  
Author(s):  
Peter Gloeckner ◽  
Klaus Dullenkopf ◽  
Michael Flouros
Keyword(s):  
Power Dissipation ◽  
High Speed ◽  
Ball Bearing ◽  
Operating Conditions ◽  
Outer Ring ◽  
Outer Diameter ◽  
Propulsion Systems ◽  
Jet Engine ◽  
Power Loss Reduction ◽  
The Impact

Operating conditions in high speed mainshaft ball bearings applied in new aircraft propulsion systems require enhanced bearing designs and materials. Rotational speeds, loads, demands on higher thrust capability, and reliability have increased continuously over the last years. A consequence of these increasing operating conditions are increased bearing temperatures. A state of the art jet engine high speed ball bearing has been modified with an oil channel in the outer diameter of the bearing. This oil channel provides direct cooling of the outer ring. Rig testing under typical flight conditions has been performed to investigate the cooling efficiency of the outer ring oil channel. In this paper the experimental results including bearing temperature distribution, power dissipation, bearing oil pumping and the impact on oil mass and parasitic power loss reduction are presented.

Characterisation of Waves and Ligaments in Films Close to an Aeroengine Ball Bearing

2019 ◽  
Author(s):  
Jee Loong Hee ◽  
Kathy Simmons ◽  
David Hann ◽  
Michael Walsh
Keyword(s):  
Flow Rate ◽  
High Speed ◽  
Ball Bearing ◽  
Capillary Waves ◽  
Operating Conditions ◽  
Research Centre ◽  
Shaft Speed ◽  
High Speed Imaging ◽  
Liquid Phases ◽  
Mass Transfers

Abstract Surface waves are observed in many situations including natural and engineering applications. Experiments conducted at the Gas Turbine and Transmissions Research Centre (G2TRC) used high speed imaging to observe multiscale wave structures close to an aeroengine ball bearing in a test rig. The dynamic behavior and scale of the waves indicate that these are shear-driven although highly influenced by gravity at low shaft speed. To understand the interactions between gas and liquid phases including momentum and mass transfers, characterization of the observed waves and ligaments was undertaken. Waves were studied at surfaces close to the ball bearing and ligaments were assessed near the cage. Characterization was in terms of frequency and wavelength as functions of speed, flow-rate, bearing axial load and gravity. The assessments confirmed the existence of gravity-capillary waves and capillary waves. Gravity-capillary waves were measured to have a longer mean wavelength on the co-current side of the bearing (gravity and shear acting together) compared to the counter-current side (gravity and shear opposing). Using a published definition of critical wavelength (λcrit), measured wavelengths at 3,000 rpm were 2.56λcrit on the co-current side compared to 1.86λcrit at the countercurrent location. As shaft speed increases, wavelength reduces with transition to capillary waves occurring at around 0.83λcrit. At shaft speeds beyond 5000 rpm, capillary waves were fully visible and the wavelength was obtained as 0.435λcrit. Flow-rate and load did not significantly influence wavelength. Wave frequency was found to be proportional to shaft speed. The gravity-capillary waves had frequencies within the range 13–25 Hz while capillary waves exhibited a frequency well beyond 100 Hz. The frequencies are highly fluctuating with no effect of load and flow rate observed. Ligaments were characterized using Weber number and Stability number. The number of ligaments increased with shaft speed. A correlation for ligament number based on operating conditions is proposed.

Kinematic investigation and fatigue life analysis of angular contact ball bearing in wide speed range based on raceway friction

2020 ◽  
Vol 72 (7) ◽  
pp. 845-850
Author(s):  
Yue Liu
Keyword(s):  
Fatigue Life ◽  
Peer Review ◽  
High Speed ◽  
Ball Bearing ◽  
Operating Conditions ◽  
Angular Contact Ball Bearing ◽  
Content Type ◽  
Speed Range ◽  
Uniform Model ◽  
Wide Speed Range

Purpose The purpose of this paper is to clarify the relationship between fatigue life and kinematics of angular contact ball bearing. It proposes a new modeling method of spin to roll ratio based on raceway friction, which is more accurate than the traditional raceway control theory. Design/methodology/approach The uniform model of spin to roll ratio based on raceway friction in a wide speed range is proposed using quasi-statics method, which considers centrifugal force, gyroscopic moment, friction force of raceway and other influencing factors. The accuracy is considerably improved compared with the static model without increasing too much computation. Findings A uniform model for spin to roll ratio of angular contact ball bearing based on raceway friction is established, and quite different relationships between fatigue life and speed under two operating conditions are found. Research limitations/implications The conclusion of this paper is based on the bearing basic fatigue life calculation theory provided by ISO/TS 16281; however, the accuracy of theory needs to be further verified. Practical implications This paper provides guidance for applying angular contact ball bearing, especially at a high speed. Originality/value This paper reveals the changing trend of fatigue life of angular contact ball bearing with the speed under different loads. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2020-0030

Analysis of Thermal Effect on Elastohydrodynamic Lubrication in Angular Contact Ball Bearing

2015 ◽  
Vol 741 ◽  
pp. 443-448
Author(s):  
Bao Ming Wang ◽  
Xia Lun Yun ◽  
Xing Yao Liao ◽  
Xue Song Mei
Keyword(s):  
Temperature Rise ◽  
High Speed ◽  
Ball Bearing ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Oil Viscosity ◽  
Angular Contact Ball Bearing ◽  
Scanning Method ◽  
Lubrication Performance ◽  
Thermal Ehl

Based on the theory of point contact thermal elastohydrodynamic lubrication (EHL),the mathematical models for the thermal EHL of high-speed angular contact ball bearing are established. Multi-grid method and multigrid integration method are respectively used to calculate out the film pressure and film thickness respectively,and the column-by-column scanning method is used to calculate temperature rise of isothermal EHL and thermal EHL. The calculation results show that, under the pure rolling condition, temperature rise of oil film temperature is mainly caused by the compression work and shear heat at inlet and the heat in contact zone mainly comes from the inlet and the heat conduction around; the temperature rise results in oil viscosity lower and the lubricating film thinner ,in this way it reduces the lubrication performance in contact pair.

The Non-Uniform Preloading Effect on Stiffness Behaviour of Angular Contact Ball Bearings

2012 ◽  
Author(s):  
Wenwu Wu ◽  
Jun Hong ◽  
Xiaohu Li ◽  
Yang Li ◽  
Baotong Li
Keyword(s):  
High Speed ◽  
Ball Bearing ◽  
Operating Conditions ◽  
Structural Performance ◽  
Angular Contact Ball Bearing ◽  
Actual Operating ◽  
Bearing Life ◽  
Bearing Stiffness ◽  
Increasing Demand ◽  
Bearing System

With the increasing demand of higher operating speed for bearing system, more challenges have been exposed on the maintaining of the bearing performance. Preloading is an effective method to handle these challenges. Traditionally, the preloading of bearing system has been applied by uniform approaches such as rigid preload and constant preload. However, this treatment may hardly deal with the optimization of preloading problem due to the non-uniformity of the bearing stiffness becomes more apparent under high-speed operating conditions. A novel and practical approach is therefore presented in this paper to incorporate the non-uniformity effect to improve the structural performance of bearing under actual operating conditions. Firstly, the critical relationship between the stiffness behaviour and the non-uniform preload is evaluated for bearing system. The stiffness problem of angular contact ball bearing system is then formulated analytically by Jones’ model. With this approach, boundary conditions are achieved to solve the local contact deformation and predict the bearing life under non-uniform preload. Finally, both the uniform preload and the non-uniform preload cases for bearing system are simulated under various operating conditions. Comparing with traditional methods, the proposed method can provide a better solution in both stiffness and life that will enable a designer to obtain a deep insight on the optimization of bearing system.

Analysis and Experimental Research on the Fluid–Solid Coupled Heat Transfer of High-Speed Motorized Spindle Bearing Under Oil–Air Lubrication

2020 ◽  
Vol 143 (7) ◽  
Author(s):  
Feng Gao ◽  
Weitao Jia ◽  
Yan Li ◽  
Dongya Zhang ◽  
Zhengliang Wang
Keyword(s):  
Heat Transfer ◽  
Temperature Rise ◽  
High Speed ◽  
Two Phase Flow ◽  
Volume Fraction ◽  
Phase Flow ◽  
Motorized Spindle ◽  
Two Phase ◽  
Spindle Bearing ◽  
Air Lubrication

Abstract For high-speed motorized spindle bearing, temperature rise is the primary factor that restricts the maximum speed of spindle and affects the stability of system. This paper addresses the lubrication and cooling of spindle bearing by exploiting the precise oil control and high cooling efficiency of oil–air lubrication. Enlightened by the bearing tribology and two-phase flow theory, a numerical model of oil–air two-phase flow heat transfer inside bearing cavity is created, with which the effects of operating condition and nozzle structure parameters on the temperature rise are studied. As the results show, with the elevation in speed, the heat generation increases rapidly, and despite the somewhat enhanced heat transfer effect, the temperature still tends to rise. Given the higher volume fraction of air than oil in the two-phase flow, the temperature rise of bearing is suppressed greatly as the air inlet velocity increases, revealing a remarkable cooling effect. When a single nozzle is used, the bearing temperature increases from the inlet to both sides, which peaks on the opposite side of the inlet. In case multiple evenly distributed nozzles are used, the high-temperature range narrows gradually, and the temperature distributions in the inner and outer rings tend to be consistent. With the increase in the nozzle aspect ratio, the airflow velocity drops evidently, which affects the heat dissipation, thereby resulting in an aggravated temperature rise. Finally, the simulation analysis is verified through experimentation, which provides a theoretical basis for selecting optimal parameters for the oil–air lubrication of high-speed bearing.

Influence of Pocket Wear on the Dynamic Characteristics of High-Speed Ball Bearing Cage

2019 ◽  
Author(s):  
Hui Li ◽  
Chen Li ◽  
Yuan Li ◽  
Shemiao Qi ◽  
Yi Liu ◽  
...  
Keyword(s):  
Dynamic Model ◽  
Dynamic Characteristics ◽  
High Speed ◽  
Ball Bearing ◽  
Rolling Bearing ◽  
Outer Ring ◽  
Wear Loss ◽  
Vibration Modes ◽  
Mass Center ◽  
Fluctuation Amplitude

Abstract Aiming at the problem of wear on the cage-pocket during the operation of high speed rolling bearing, a dynamic model of high-speed ball bearing was established considering the wear loss of the ball-pocket, and the simulation was carried out to research on the interaction among the balls, the inner ring, the outer ring and the cage with different wear loss of the ball-pocket. The effect of the pocket wear on the trajectory of the cage’s mass center and the skidding ratio of cage was obtained. It was found out that the mass-center trajectory of the cage presents two vibration modes with different amplitudes which emerges alternatively. Moreover, the wear loss of the ball-pocket has little effect on the average skidding ratio of the cage, however, the fluctuation amplitude would become larger as the wear increase. This study can provide theoretical guidance for the design of bearing cage pocket size.

Sign in / Sign up

Export Citation Format

Share Document